17.3.2 CHANGE-APRT

•

The values for APIPADDR, NETMASK and TAIPADDR are optional and will be generated by DB if not filled in. The following restrictions apply:

–

The APIPADDR is mandatory in the case of the AP connected via an IP network.

–

If the TAIPADDR is entered the APIPADDR has to be entered, too.

•

TYPE=ROUTTBL

Both, the entries in the IP routing tables for NCUI and STMI boards can be changed with AMO APRT. The entries in the IP routing tables for STMI boards are the same for all STMI boards, no specific STMI board can therefore be addressed in the MTYP=STMI branch.
After changing the IP routing tables the board data has to be loaded to the corresponding board by means of the AMOs BSSU/USSU.

•

TYPE=ALTROUT

The entry in the alternate routing table for a particular source group index and position can be modified.

Although the parameter ARTCNR is defined as a key-numeral number , it can contain only numeric characters, except for one condition :

When the combination ARTCNR=*** ARTCNRNG=0 is fullfilled the parameters of the corresponding record are reset to their initial values (ARTCNR is deleted and ARTCNRNG is set to 0).

If ARTCNR contains non-numeric characters but is not equal to "***", the AMO breaks with error message F18.
If ARTCNR is equal to "***" but ARTCNRNG is not equal to zero, ARTCNR and ARTCNRNG are ignored (advisory message H14 is given) but all other entered parameters will take effect.

TYPE=ALTERR

The entries of the Alternate Routing numbers on Error for both types OOS and APE can be modified per source group.

Procedure overview


Command Code	Parameter
CHANGE-APRT	TYPE=APNET,LTU=<number>, [APIPADDR=<number>], [NETMASK=<number>], [TAIPADDR=<number>];
	\| TYPE=ROUTTBL,
	[MTYPE=STMI],[DSTADDR1=<number>],[DSTMSK1=<number>], [ROUTER1=<number>], [DSTADDR2=<number>], [DSTMSK2=<number>], [ROUTER2=<number>], [DSTADDR3=<number>],[DSTMSK3=<number>], [ROUTER3=<number>], [DSTADDR4=<number>], [DSTMSK4=<number>], [ROUTER4=<number>], [DSTADDR5=<number>],[DSTMSK5=<number>], [ROUTER5=<number>], [DSTADDR6=<number>], [DSTMSK6=<number>], [ROUTER6=<number>], [DSTADDR7=<number>],[DSTMSK7=<number>], [ROUTER7=<number>], [DSTADDR8=<number>], [DSTMSK8=<number>], [ROUTER8=<number>];
	\| [MTYPE=NCUI],LTU=<number>, [DSTADDR1=<number>],[DSTMSK1=<number>], [ROUTER1=<number>], [DSTADDR2=<number>], [DSTMSK2=<number>], [ROUTER2=<number>], [DSTADDR3=<number>],[DSTMSK3=<number>], [ROUTER3=<number>], [DSTADDR4=<number>], [DSTMSK4=<number>], [ROUTER4=<number>], [DSTADDR5=<number>],[DSTMSK5=<number>], [ROUTER5=<number>], [DSTADDR6=<number>], [DSTMSK6=<number>], [ROUTER6=<number>], [DSTADDR7=<number>],[DSTMSK7=<number>], [ROUTER7=<number>], [DSTADDR8=<number>], [DSTMSK8=<number>], [ROUTER8=<number>];
	\| TYPE=ALTROUT,SRCGRP=<number>, POS=<number>, [ALTRTNR=<key-num>], [ACCODE=<key-num>], [ARTCNR=<key-num>], [ARTCNRNG=<number>];
	\| TYPE=ALTERR,SRCGRP=<number>, \| ALRTYPE=OOS, [ALTRTNR=<key-num>], [GWIPADR=<number>] \| [EXTNO=<number>]; \| ALRTYPE=APE, [ALTRTNR=<key-num>],[EXTNO=<number>];

${DocTitle}, ID: ${DocID}

© 02/2025 Mitel Networks Corporation. - All rights reserved.
Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG.
All other trademarks herein are the property of their respective owners.