83.4 Parameter Description


BCHL	B-channel number
	Type of Input	:	Single value, && (max.2), optional
	Possible Values	:	1 to 30
	Default Value	:	all B-channels

CIR	Circuit number of CMI Basestation
	Type of Input	:	Single value, && (max.2), optional
	Possible Values	:	8 to 23
	Default Value	:	all circuits of CMI Basestation

LTG	Line Trunk Group
	Type of Input	:	Single value, optional
	Possible Values	:	1 to 32
	Default Value	:	1	Atlantic platforms allow only LTG number 1

LTU	Line Trunk Unit
	Type of Input	:	Single value, required
	Possible Values	:	1 up to 15	Depends on HW type
			17 to 99	LTU range for IPDA AP shelves

OFFTYPE	Selection of type of deactivate job
	Type of Input	:	Single value, optional
	Possible Values	:	DC	Deactivate with pre- blocking
			DI	Deactivate immediately
			L	Long-term deactivation
	Default Value	:	DC for TYPE	for TYPE = PEN / STNO
			L for TYPE	for TYPE = BCHAN
			DI for TYPE	for TYPE = STNO, SVC = MSN

ONTYPE	Selection of type of activate job
	Type of Input	:	Single value, optional
	Possible Values	:	ACL	Activation with conditional loading
			AUL	Activation with unconditional loading
			ANL	Activation with no loading
	Default Value	:	ACL	for TYPE = PEN / STNO
			ANL	for TYPE = BCHAN
			ANL	for TYPE = STNO, SVC = MSN

PEN1	Port equipment number of the first or only line to be switched (LTG-LTU-SLOT-CCT)
	Type of Input	:	Compound value, required
	Possible Values	:	g-uu-sss-ccc
	g= LTG Number	:	1 ( no other value)
	uu= LTU Number		1 to 15 in HHS (Host Shelf)
			17 to 99 in AP (Access Point Shelf)
			16 not defined
	sss= Slot	:	1 to 121 in increments of six or one depending on HW type (See AMO UCSU)
	ccc= Line Number	:	0 to 254
A suitable module must be configured to the slot addressed by PEN (AMO BCSU).
The possible LTU and Slot values for PEN depend on the systems architecture and can be found in the BCSU AMO description.
The possible Line values depend on the module type and its functionality. They can be listed using DISP-BCSU: TYPE=PEN1 [,LTG=, LTU=, SLOT=, CCT=]; which will also output the actual PEN status (e.g. NOT CONNECTED).

PEN2	Port equipment number of the last line to be switched
	Type of Input	:	Compound value, optional
	Possible Values	:	same as for PEN1

REFOFF	Switch reference clock generator as well
	Type of Input	:	Single value, optional
	Possible Values	:	Y	Switch off ref. clock generator if additional available, otherwise prompt
			N	Do not switch off ref. clock generator
			PROMPT	Prompt if ref. clock generator found
	Default Value	:	PROMPT

SLOT	Slot
	Type of Input	:	Single value, required
	Possible Values	:	1 to 121 in increments of six or one depending on HW type (see AMO-UCSU)

STNO	Station number
	Type of Input	:	Single values,
			chained single values (not allowed for CHANGE),
			ranges (not allowed for CHANGE)
			required
	Possible Values	:	STNO must exist in the dialing plan
			A max. of 10 values is possible, e.g. 3 ranges and 4 chained single values. For CHANGE only single value allowed

SVC	Selection of services for configuration with terminals of different services for S0-Bus or DCI
	Type of Input	:	Single value, & (max. 6)
			optional
	Possible Values	:	VCE	Voice
			FAX	Facimile
			DTE	Data terminal equipment
			MSN	MSN number
			ALL	All services
	Default Value	:	ALL

TSI	Terminal Selection Identifier for subscribers and bus devices
	Type of Input	:	Single value, optional
	Possible Values	:	1 to 8

TYPE	Type of device to be switched
	Type of Input	:	Single value, required
	Possible Values	:	ACTIVATE/DEACTIVATE :
			PEN	Port equipment number
			STNO	Station number
			BCHAN	B-channel of Trunk circuits

			RESTART :
			PEN	Port equipment number
			STNO	Station number

			CHANGE :
			SIGNON	Sign on extension to pen
			SIGNOFF	Sign off extension

${DocTitle}, ID: ${DocID}

© 02/2025 Mitel Networks Corporation. - All rights reserved.
Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG.
All other trademarks herein are the property of their respective owners.