102.4 Parameter Description


ACTION	Loading type of board
	Type of Input	:	Single value, optional
	Possible Values	:	LOAD	forced loading for the board
			RESET	reset of the forced loading
	Default Value	:	LOAD

COMPLEX	RTO complex.
	Type of Input	:	Single value, mandatory
	Possible Values	:	UNIT	RTO of a unit,
			RJGRP	Test group,
			RJ	Individual routine test.

FCTID	Function identification for multi function boards
	Type of Input	:	Single value, optional
	Possible Values	:	0 - 255
	Default Value	:	0	( 0=non multi function board)

OUTPUT	Output mode.
	Type of Input	:	Single value, optional
	Possible Values	:	STATUS	Outputting the status,
			ALL	Outputting all data.
	Default Value	:		STATUS

PARTNO	Part number of board
	Type of Input	:	Single value, optional
	Possible Values	:	any text string, max. 10 characters
	Default Value	:	Code number in accordance with the table of permissible modul types, eg., "Q2057-X..."

PIT	Peripheral Interface Task.
	Type of Input	:	Single value, mandatory
	Possible Values	:	LWLOAD	Load loadware from Hard disk,
			FLASH	Load all flash memory modules.

RJ	Routine job.
	If the parameter is not specified, all routine jobs will be output.
	Type of Input	:	Linked single values, mandatory (SET) Linked single values, optional (DISPLAY)
	Possible Values	:			RJGRP:
			IPREQ	Interface processor (IP) display	RJC
			CCHREQ	Cross channel (CCH) display	RJC
			MBUAREQ	Displaying all message buffer units (MBU)	RJC
			IOCCAREQ	Displaying all input/output controllers (IOCC) or the input/output control central switching network (IOCSN)	RJC
			IOCGREQ	Displaying the input/output controller GP (IOCG) or the input/output controller (IOC)	RJC
			DCLREQ	Displaying the data comm. link (DCL) or the double communcation link (DDCL)	RJC
			MBUATEST	Testing all message buffer units (MBU)	RJC
			IOCCATST	Testing all input/output controllers, central (IOCC) or the input/output control central switching network (IOCSN)	RJC
			CCHIECBS	Testing the IEC bus between the RJP1 CCH modules	RJC
			IPTEST	Interface processor (IP) test	RJC
			DPTIMOUT	HW monitor circuit to be used for initiating multibus timeouts on the DP module	RJP1
			DPWDCTR0	HW monitor circuit to be used for starting watchdog counter 0 on the DP module	RJP1
			DPWDCTR1	HW monitor circuit to be used for starting watchdog counter 1 on the DP module	RJP1
			DPRDYREQ	Displaying the +ready+ line of the partner data processor	RJP1
			DCLTEST	Testing the data communication link (DCL) or the double communication link (DDCL)	RJP1
			IOCGTEST	Testing the input/output controller group (IOCG) or the input/output controller (active) performs test on standby)	RJP1
			MEMACEA	Reading all memory cells on all M8M and DPML286 memory modules (parity check)	RJP1
			MEM1AREQ	Displaying 1-bit errors on all M2M memory modules	RJP1
			GSNMTSCM	Testing the MTS/GSN in the standby section by reading any TSL on every component in MTS64 modules	RJP1
			LTUCUPRQ	Displaying all microprocessors of the LTUC module in an LTG	RJP1
			SYMCHKAL	Testing the SLMO board to see if the Symphony device is still alive.	RJP1
			CONWADP	Testing connection between WAML and ADP	RJP1
			CIRA	Testing all circuits on a specific line circuit module	RJP2
			CIRAENDA	Testing all terminals on all circuits of a specific line circuit module	RJP2
			UPAREQ	Displaying all microprocessors in the periphery of an LTG	RJP3
			LTUAHWYA	Testing all time slots on all highways leading to all LTU mod. Testing the LTG shelf (without the service unit)	RJP3
			STBYWYA	Standby Highway A	RAP3
			BDHWYTST	Board Highway Test	RAP1
			SIUTSTTR	Echoing any test transmitter on the associated test receiver	RJP3
			SIUDTO	Echoing a continuous tone on any SLC of any dial tone receiver	RJP3
			SIUPTO	Echoing a cadenced tone on any SLC of a dial tone receiver	RJP3
			SIUCSCR	Echoing any code transmitter of an SIU periphery (SIU type 2) on all code receivers of the standard SIU	RJP3
			SIUPCSCR	Echoing all code transmitters on all code receivers of the SIU periphery module (SIU type 2/3)	RJP3
			SURVPATA	Survivability Path test	RJP1
			LTUCCCBM	LTUCC Central Byte Manipulation test loop	RJP3
			SIUPTDSA	TDS loopback test event DSC	RJP3
			SIUTDSA	TDS loopback test event DSCX	RJP3

RJFREQ	Start frequency of single routine test jobs.
	Type of Input	:	Single value, manaatory
	Possible Values	:	0 to 255
			0	Never tested,
			1	Start at every run,
			2	Start at every 2nd run,
			.
			.
			x <= 255	Start at every xth run.

RJGRP	Routine job groups.
	Type of Input	:	Linked single values, mandatory
	Possible Values	:	RJC	Display firmware,
			RJP1	Test central units,
			RJP2	Test interface circuits,
			RJP3	Test peripheral units.

RJPAUSE	Pause time between two tests (seconds).
	Type of Input	:	Group value, optional.
	Possible Values	:	1 to 65535

RJSTART	Start time for routine job groups (hours).
	Type of Input	:	Group value, optional
	Possible Values	:	0 to 23

RJSTOP	Stop time for routine job groups (hours).
	Type of Input	:	Group value, optional
	Possible Values	:	1 to 24

STARTAUT	Start authorization of AM for routine tests.
	Type of Input	:	Single value, mandatory (SET, COMPLEX=MODUL) Group value, optional (SET, COMPLEX=RJGRP)
	Possible Values	:	Y, N

UNIT	Hardware unit.
	Type of Input	:	Linked single values, mandatory
	Possible Values	:	BPA, BPB	CC half,
			GP1A ... GP32A	LTG half,
			GP1B ... GP32B	"
			CC	Entire CC,
			LTG	all LTGs,
			SWU	Entire SWU.

${DocTitle}, ID: ${DocID}

© 02/2025 Mitel Networks Corporation. - All rights reserved.
Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG.
All other trademarks herein are the property of their respective owners.