133.4
Error Messages and Advisories
133.4.1
Error Messages
F01:
DPLN <DPLN> IS ENTERED MORE THAN ONCE
Cause:
Parameter value for parameter DPLN entered twice.
Action:
Check parameter DPLN.
F02:
NUMBER OF VALUES FOR DPLN AND <PARAM> DIFFERENT
<PARAM> cannot have the values LROUTE and LAUTH.
Cause:
A number of PARAM>=LROUTE or LAUTH values which was neither 1 nor the number of specified DPLN groups was specified.
Action:
Check the number of values for DPLN, LROUTE and LAUTH.
F03:
IF PARAMETER LROUTE OR LAUTH ENTERED, PARAMETER DPLN IS REQUIRED
F04:
IF PARAMETER DPLN IS NOT ENTERED PARAMETER <PARAM> MAY ONLY GET ONE VALUE.
<PARAM> can have the values LROUTE aund LAUTH.
Cause:
Parameter DPLN was not specified, because an addition was to be made for all DPLN groups, or it was forgotten. In any case, more than one value was specified for LROUTE or LAUTH.
Action:
Check number of values of DPLN,LROUTE and LAUTH.
F05:
THE FIRST FIELD OF A LDP MAY NOT CONTAIN A WILDCARD (X,T,Z) AND MORE THAN 6 DIGITS
Cause:
The first field of an LDP is the routing code of this LCR digit pattern.
Action:
It may therefore contain only digits 0-9 and *.
F06:
THE LEADING DIGITS OF LDP ARE NOR DEFINED AS ROUTING CODE.
[FOR DPLN <DPLN1>[,<DPLN2>[...]]]
[WITH CPS <CPS1>[,<CPS2>[...]]].
Cause:
The first field of the current LCR digit pattern does not find a digit analysis result in the digit analysis tables administered by AMO WABE (in any DPLN and CPS values displayed).
Action:
Before an addition can be made to the LCR dialing plan, a digit analysis result relevant for LCR must be created for the routing code in the digit analysis tables, using AMO WABE.
F07:
THE LEADING DIGITS OF LDP LEAD
TO NONE OF THE DIGIT ANALYSIS RESULTS RELEVANT FOR LCR
[FOR DPLN <DPLN1>[,<DPLN2>[...]]]
[WITH CPS <CPS1>[,<CPS2>[...]]].
(AMO-WABE, DAR)
Cause:
The first field of the current LCR digit pattern finds digit analysis results in the digit analysis tables, but they are not relevant for LCR.
Action:
If this routing number is to be assigned to LCR, the ’incorrect’ digit analysis results must be changed into digit analysis results relevant for LCR,
using AMO-DPLN (as specified in the error message).
F08:
THE DIAL PATTERN LDP MAY NOT BE LONGER THAN 22 CHARACTERS
F09:
THE LEADING DIGITS OF LDP ARE
ALREADY USED BY AMO RICHT AS ROUTING CODE
[FOR DPLN <DPLN1>[,<DPLN2>[...]]]
[WITH CPS <CPS1>[,<CPS2>[...]]].
Cause:
The first field of the current LCR digit pattern shows digit analysis results in the digit analysis tables, but they have already been used by AMO RICHT.
Action:
Specify another routing code or stop use by AMO RICHT.
F10:
A CORRESPONDING VALUE FOR PARAMETER LAUTH MUST BE ENTERED BECAUSE THE LDP WAS RESTRICTED OR NOT YET EXISTING IN DPLN <DPLN>.
Cause:
The digit pattern LDPNO was restricted or does not yet exist for the specified DPLN. No LAUTH has therefore been assigned to the LROUTE. An LAUTH must be specified.
Action:
Specify the LAUTH assigned to the LROUTE.
F11:
LDPNO <LDPNO> NOT YET EXISTING.
Cause:
The value of parameter LDPNO is outside the range created.
Action:
Give LDPNO the relevant value; it can be found with DISPLAY for the valid range or all LDPs.
F12:
LDP EXISTS ALREADY WITH LDPNO <LDPNO>.
Cause:
A same digit pattern has already been created with the LDPNO specified. Note: two digit patterns are the same if the shorter of the two has the same digit pattern as the longer over its entire length (e.g. 91-XX is the same as 91-XX-Z).
Action:
Correct LDP; there may be errors in the digit pattern design.
F13:
LDP CANNOT BE INSERTED - THERE IS NO FREE FICTIVE LINE.
F14:
LDP CANNOT BE ADDED - THERE IS NO FREE <PARAM>-MEMORY (AMO-DIMSU, PARAMETER <PARAM><PARAM>)
Occurs with: ADD, CHANGE
Cause:
There is no free FLEXAMA memory of the specified type <PARAM><PARAM>.
Action:
AMO DIMSU can be used to change the distribution of the FLEXAMA memory. Memory of the type specified in the error message must be made available.
F15:
LDP CANNOT BE ADDED/CHANGED - THERE IS NO MORE LDP-MEMORY (AMO-DIMSU, PARAMETER LDP)
F16:
THE LAST CHARACTER OF LDP MAY NOT BE W.
F17:
LROUTE <LROUTE> IS NOT DEFINED (AMO-RICHT).
Cause:
The LCR route specified in parameter LROUTE has not yet been created with AMO RICHT.
Action:
Correct parameter LROUTE or create with AMO RICHT before trying again.
F18:
LROUTE <LROUTE> IS NOT DEFINED FOR LCR.
Cause:
The route specified in parameter LROUTE has been created with AMO RICHT, but has not been defined for LCR.
Action:
Correct parameter LROUTE or change the route with AMO RICHT.
F19:
LROUTE <LROUTE> IS ILLEGAL: NO ROUTE ELEMENTS DEFINED (AMO LDAT)
Cause:
No route element has been defined with AMO LDAT for the LCR route specified in parameter LROUTE.
Action:
Correct parameter LROUTE or use LDAT to create route elements for the LCR route.
F20:
SPC < <SPC> ILLEGAL: LESS THAN LENGTH OF LDP
Cause:
An SPC value which is less than the length of the LDP was specified. The wildcards T and Z are not counted as being part of the length of a dial pattern.
Action:
Correct SPC value.
F21:
ILLEGAL CHARACTER IN DIALING PATTERN LDP:
LDP MAY ONLY CONTAIN THE CHARACTERS 0 TO 9, A TO D, *, #
AND THE WILDCARDS X,T,Z.
Cause:
Illegal character in digit pattern.
Action:
Correct digit pattern.
F22:
THERE IS NO LDP.
F23:
CHANGE OF LAUTH IN DPLN <DPLN> NOT POSSIBLE, BECAUSE THE LDP IS RESTRICTED OR NOT YET EXISTING IN THIS DPLN.
Cause:
Only a LAUTH to which a valid LROUTE has been assigned can be changed.
Action:
Specify valid LROUTE.
F24:
W MAY ONLY BE IN A FIELD ALONE.
F25:
EITHER PARAMETER LDP OR PARAMETER LDPNO MAY BE ENTERED
F26:
THE SPECIFIED DIALING PATTERN WAS NOT FOUND.
F27:
THERE IS NO MORE LCR DIALPLAN CACHE MEMORY AVAILABLE.
PLEASE TRY TO INCREASE THIS MEMORY USING AMO DIMSU, PARAMETER LDPLNC@
OR TRY REORGANIZE THE CACHE BY MEANS OF DELETE AND REBUILD.
F28:
Either LROUTE or PROFIDX or GWNO MAY BE ENTERED. BOTH TOGETHER ARE NOT ALLOWED.
F29:
PROFIDX @@@@ IS NOT DEFINED (AMO-LPROF).
F30:
THE PARAMETER PPPPPP HAS BEEN ASSIGNED TO THE ENTERED LDPNO/LDP.
Help: DISP-LDPLN:TYPE=LDP,DIPLNUM=@@@@,{(max 1) LDPNO=, LDP=},PPPPPP=<value>;
F31:
THE MARKER Y MAY NOT BE IN A FIELD ALONE.
F32:
THE MARKER Y MUST BE THE FIRST CHARACTER IN A FIELD.
F33:
THE MARKER Y CAN APPEAR ONLY ONCE IN AN LDP.
F34:
THE DIPLNUM @@@@ DOES NOT EXIST.
F35:
DIPLNUM @@@@ CAN NOT BE DELETED , BECAUSE IT IS STILL ASSIGNED TO AT LEAST ONE LCR DIAL PATTERN
F36:
NO VALID DIALING PATTERN FOR DIPLNUM @@@@ AVAILABLE
F37:
DIPLNUM @@@@ IS RESERVED FOR @@@ NUMBERING PLAN. NO LCR PATTERN MAY BE ADDED FOR DIPLNUM @@@@.
F38:
DIPLNUM @@@@ IS RESERVED FOR @@@ NUMBERING PLAN. CONFIGURE IT WITH: ADD-LDPLN:LCRADM,@@@@,8,@@@@,'@@@ NUMBERING PLAN';
F39:
DIPLNUM @@@@ IS ALREADY ASSIGNED
F40:
ENTRY COULD NOT BE DELETED COMPLETELY SUCCESFUL. IT MAY CAUSE INCONSISTANCY IN DATABASE.
F41:
The entered parameter @@@@@@@@@@ contains more values than allowed.
${DocTitle}
, ID:
${DocID}
©
02/2025
Mitel Networks Corporation. - All rights reserved.
Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG.
All other trademarks herein are the property of their respective owners.