154.6.3 Appendix 2, Part 3: Initblocks 41 till 60

Longtimer	Default (ms)	Description	Remark
L1	0	reserve
L2	0	reserve
L3	0	reserve
L4	0	reserve
L5	0	reserve
L6	0	reserve
L7	0	reserve

Shorttimer	Default (ms)	Description	Remark
S1	0	reserve
S2	0	reserve
S3	0	reserve
S4	0	reserve
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve

Parameter	Default	Description		Remark
P1	0	reserve
P2	0	reserve
P3	0	signaling direction
		0	bothway
		1	outgoing
		2	incoming
P4	0	reserve
P5	0	reserve
P6	0	reserve
P7	0	reserve
P8	0	intercept to attendant for backward dialing on outgoing calls
		0	no intecept to attendant
		1	with intecept to attendant	(only test)
P9	1	override for EB5-system for incoming calls
		0	intecept to attendant
		1	override on busy subscriber
P10	0	reserve
P11	0	reserve
P12	0	reserve
P13	1	send blocking signal
		0	blocking with a-bit
		1	blocking with b-bit
		2	blocking with c-bit
P14	1	send block acknowledgement signal
		0	no block acknowledgement signal
		1	block acknowledgement signal with b-bit impulse

Longtimer	Default (ms)	Description	Remark
L1	0	reserve
L2	0	reserve
L3	0	reserve
L4	0	reserve
L5	0	reserve
L6	0	reserve
L7	0	reserve

Shorttimer	Default (ms)	Description	Remark
S1	0	reserve
S2	0	reserve
S3	0	reserve
S4	0	reserve
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve

Parameter	Default	Description		Remark
P1	0	dialing method
		0	pulse dialing
		1	DTMF dialing with CO register
		2	MFC dialing
P2	0	reserve
P3	0	signaling direction
		0	bothway
		1	outgoing
		2	incoming
P4	7	call charge indication
		7	no charges from CO (basic version)
		8	charges from CO (metering version) ab=00
P5	0	reserve
P6	0	dial tone supervision
		0	without
		1	with
P7	20	answer supervision on outgoing calls
		0	no supervision
		1-200	supervision in 10 seconds steps
P8	0	reserve
P9	0	reserve
P10	2	release request from CO on outgoing calls
		2	with forced release (ab=10-metering version)
		3	with clear back or forced release
P11	0	idle code on line
		0	idle code=54H for new systems at E10B (CCITT)
		1	idle code=55H for old systems at E10A
P12	0	reserve
P13	0	reserve
P14	0	reserve

Longtimer	Default (ms)	Description	Remark
L1	0	reserve
L2	0	reserve
L3	0	reserve
L4	0	reserve
L5	0	reserve
L6	0	reserve
L7	0	reserve

Shorttimer	Default (ms)	Description	Remark
S1	0	reserve
S2	0	reserve
S3	0	reserve
S4	0	reserve
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve

Parameter	Default	Description		Remark
P1	0	dialing method
		0	pulse dialing
		1	MFV dialing with CO register
		2	MFC dialing
P2	0	reserve
P3	0	signaling direction
		0	bothway
		1	outgoing
		2	incoming
P4	7	call charge indication
		7	no charges from CO (basic version)
		8	charges from CO (metering version) ab=00
P5	0	reserve
P6	0	dial tone supervision
		0	without
		1	with
P7	20	answer supervision on outgoing calls
		0	no supervision
		1-200	supervision in 10 seconds steps
P8	0	reserve
P9	0	reserve
P10	2	release request from CO on outgoing calls
		2	with forced release (ab=10-metering version)
		3	with clear back or forced release
P11	0	idle code on line
		0	idle code=54H for new systems at E10B (CCITT)
		1	idle code=55H for old systems at E10A
P12	0	reserve
P13	0	reserve
P14	0	reserve

Longtimer	Default (ms)	Description	Remark
L1	40	seizure detection for incoming calls (10-200 ms)
L2	200	supervision of seizure acknowledgement for outgoing calls (200-5000 ms)
L3	100	alarm detection (100-10000 ms)
L4	0	reserve
L5	0	reserve
L6	0	reserve
L7	0	reserve

Shorttimer	Default (ms)	Description	Remark
S1	0	reserve
S2	0	reserve
S3	0	reserve
S4	0	reserve
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve

Parameter	Default	Description		Remark
P1	2	dialing method
		0	pulse dialing
		1	MFV dialing with CO register
		2	MFC dialing
P2	120	clear back supervision time for outgoing calls after answer
		0	no supervision
		1-255	supervision time in 1-seconds steps
P3	0	signaling direction
		0	bothway
		1	outgoing
		2	incoming
P4	6	call charge simulation with answer for outgoing calls
		6	without simulation (metering version)
		7	with charge simulation (universal version)
P5	0	release supervision on incoming calls
		0	no supervision
		1-255	supervision time in 10 seconds steps for slovak 12 =120 Sec.
P6	0	dial tone supervision for outgoing calls
		0	without
		1	with
P7	12	answer supervision for outgoing calls
		0	no supervision
		1-255	supervision time in 30 second steps
P8	0	malicious call tracing
		0	without
		2	with MTC line signal
P9	0	override from CO
		0	ignore signal
		1	override on subscriber
		2	intercept to attendant
P10	0	forced release from CO
		0	possible
		1	no possible
P11	0	malicious call tracing swith off for outgoing calls if A-subscriber release
		0	forward release after registration
		1	wait or release from CO after registration
P12	0	reaction for wrong bit combination on incoming calls
		0	send forced release - line signal
		1	send busy tone from DH	not implemented
P13	0	send test seizure for outgoing calls
		0	without
		1	with, if no reaction of CO on forward release
P14	0	czech / slovak signaling
		0	czech signaling
		1	slovak signaling

Longtimer	Default (ms)	Description	Remark
L1	80	seizure detection for incoming calls (10-200 ms)
L2	2000	supervision of seizure acknowledgement for outgoing calls (200-5000 ms)
L3	10000	alarm detection (100-10000 ms)
L4	0	reserve
L5	0	reserve
L6	0	reserve
L7	0	reserve

Shorttimer	Default (ms)	Description	Remark
S1	0	reserve
S2	0	reserve
S3	0	reserve
S4	0	reserve
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve

Parameter	Default	Description		Remark
P1	0	dialing method
		0	pulse dialing
		1	MFV dialing with CO register
		2	MFC dialing
P2	0	clear back supervision time for outgoing calls after answer
		0	no supervision
		1-255	supervision time in 1-seconds steps
P3	0	signaling direction
		0	bothway
		1	outgoing
		2	incoming
P4	6	call charge simulation with answer for outgoing calls
		6	without simulation (metering version)
		7	with charge simulation (universal version)
P5	0	supervision of forward release
		0	no supervision
		1-255	supervision time in 10 s.-steps for Slovak 12=120s
P6	1	dial tone supervision for outgoing calls
		0	without
		1	with
P7	0	answer supervision for outgoing calls
		0	no supervision
		1-255	supervision time in 30 seconds steps
P8	0	malicious call tracing
		0	without
		2	with MTC line signal
P9	0	override from CO
		0	ignore signal
		1	override on subscriber
		2	intercept to attendant
P10	0	forced release from CO
		0	possible
		1	no possible
P11	0	reserve
P12	0	reserve
P13	0	send test seizure for outgoing calls
		0	without
		1	with, if no reaction of CO on forward release
P14	0	reserve

Longtimer	Default (ms)	Description	Remark
L1	0	reserve
L2	0	reserve
L3	0	reserve
L4	0	reserve
L5	0	reserve
L6	0	reserve
L7	0	reserve

Shorttimer	Default (ms)	Description	Remark
S1	0	reserve
S2	0	reserve
S3	0	reserve
S4	0	reserve
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve

Parameter	Default	Description		Remark
P1	0	reserve
P2	0	reserve
P3	0	signaling direction
		0	bothway
		1	outgoing
		2	incoming
P4	10	call charge simulation for outgoing calls
		9	call charge on a-bit; answer on b-bit
		10	call charge on b-bit; no answer
P5	0	reserve
P6	1	dial tone supervision for outgoing calls
		0	without
		1	with
P7	0	reserve
P8	0	reserve
P9	0	reserve
P10	0	"rering" signal
		0	evaluate
		1	ignore
P11	0	reserve
P12	0	reserve
P13	1	send inhibit
		0	ab-bit = 11
		1	ab-bit = 00
P14	0	reserve

Longtimer	Default (ms)	Description	Remark
L1	0	reserve
L2	0	reserve
L3	0	reserve
L4	0	reserve
L5	0	reserve
L6	0	reserve
L7	0	reserve

Shorttimer	Default (ms)	Description	Remark
S1	0	reserve
S2	0	reserve
S3	0	reserve
S4	0	reserve
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve

Parameter	Default	Description		Remark
P1	0	reserve
P2	0	reserve
P3	0	signaling derection
		0	bothway
		1	outgoing
		2	incoming
P4	10	call charge simulation for outgoing calls
		9	call charge on a-bit; answer on b-bit
		10	call charge on a-bit; no answer
P5	0	reserve
P6	1	dial tone supervision for outgoing calls
		0	without
		1	with
P7	0	reserve
P8	0	reserve
P9	0	reserve
P10	0	"rering" signal
		0	evaluate
		1	ignore
P11	0	reserve
P12	0	reserve
P13	1	send inhibit
		0	ab-bit = 11
		1	ab-bit = 00
P14	0	reserve

Longtimer	Default (ms)	Description	Remark
L1	200	min. time for a valid signal or signal (20-5000 ms)	TMSFP: 300 ms
L2	1500	sending time for outgoing seizure (400-3000 ms)	TMSFP: 1000 ms
L3	1500	sending time release or release acknowledge (400-3000 ms)	TMSFP: 1000 ms
L4	1000	ignore incoming signals after end of send /end of receive (500-2000 ms)
L5	10000	outgoing guard time (5000-30000 ms)
L6	10000	release acknowledgement supervision (5000-30000 ms)
L7	1000	ignore incoming signals after end-of-dial (if P8=2 or 3) (500-5000 ms) max. time for valid signals and min. sending time for blocking (if P14= 1) (5-30 s)	only TMLBL   only TMSFP: 10 s

Shorttimer	Default (ms)	Description	Remark
S1	0	reserve
S2	0	reserve
S3	0	listener / control channel 0 listener channel 1 control channel	only DIUC64 LWVAR=F/G
S4	0	reserve
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve

Parameter	Default	Description		Remark
P1	0	release
		0	no release signal
		1	release signal
P2	0	release acknowledgement
		0	no release acknowledgement
		1	with release acknowledgement (if P1=1)
P3	20	call time supervision		TMSFP: 0
		0	without supervision
		1-255	supervision time in 30 sec. steps
P4	0	direct inward dialing (pseudo-DID)		TMLBL
		0	no pseudo-function
		1	with pseudo-function	only TMLBL X200
		2	selectiv ringing-Attention: LW-error
P5	0	level switching		TMLBL,TMEMW,TMSFP
		0	without level switching
		1	with level switching
P6	0	line adaptation		only TMLBL
		0	real impedance with 3,3 kOhm (Party line) LIN_OFF, RX_OFF	for polen-trunk cofidx=0 long line for polen-trunk cofidx=1 short line for polen-station cofidx=4 long line for polen-station cofidx=5 short line
		1	real impedance no party line function LIN_ON, RX_OFF	no valid sicofi-data available
		2	complex impedance with 3,3 kOhm (Party line) LIN_OFF, RX_ON	for BRD-trunk cofidx=2 long line for BRD-trunk cofidx=3 short line for BRD-station cofidx=6 long line for BRD-station cofidx=7 short line
		3	complex impedance no party line function LIN_ON, RX_ON	no valid sicofi-data available
P7	1	answer supervision for incoming traffic		TMLBL,TMSFP
		0	without answer supervision
		1-255	supervision time in 30 sec. steps
P8	0	subsequent ringing before answer (only if P1=0)
		0	subsequent ringing results in release und new seizure
		1	ignore subsequent ringing
		2	subsequent ringing after EOD results in call to attendant	only on DITW with DTMF-DID or on digit initialization
		3	subsequent ringing after EOD busy results in override/camp-on, subsequent ringing after EOD-free results in call to attendant	only on DITW with DTMF-DID or on digit initialization
		12	simulation of subsequent ringing if EOD busy: call on attendant	only TMSFP
		13	simulation of subsequent ringing if EOD busy: override	only TMSFP
P9	0	subsequent ringing on state of call (only if P1=0)
		0	subsequent ringing results in release und new seizure
		1	ignore subsequent ringing
		2	send 2 kHz continuous tone	only TMLBL
		3	send 2 kHz intermittent-tone	only TMLBL
P10	3	tone signal time ( if P9=2 or 3)		only TMLBL
		0	sending time = 255 sec.
		1-255	sending time in 1 sec. steps
P11	0	tone-frequency (if P9=2 or3)
		0	400/450 Hz
		1	450 Hz
		2	500/550 Hz
		3	1000/2000 Hz
P12	0	seizure signaling		TMSFP, DIUC64
		0	seizure with line signaling
		1	outgoing seizure without line signaling, without refresh
		2	outgoing seizure without line signaling, with refresh	only DIUC64 LWVAR=F/G
		3	automatic incoming seizure without line signaling, without refresh	only DIUC64 LWVAR=F/G
		4	automatic incoming seizure without line signaling, with refresh	only DIUC64 LWVAR=F/G
P13	0	outgoing reseizure lockout for lines without release signal		only TMSFP
		0	without outgoing reseizure lockout time
		1	with outgoing reseizure lockout time (L5)
P14	0	out of service / blocking signaling		only TMSFP
		0	no signal
		1	sending continuous signal

Longtimer	Default (ms)	Description	Remark
L1	96	send seizure acknowledgement after detection (30-800 ms)
L2	1000	message pulseon collect call (if P11=1 or 2) (100-5000 ms)
L3	2000	finish character pulse on collect call (if P11=1 or 2) (100-5000 ms)
L4	10000	detection of faulty bit combinations from line (1000-30000 ms)
L5	200	detection time of forced release of CO on outgoing calls (100-800 ms)
L6	400	max. time for charge pulse (300-800 ms)
L7	5000	supervision of seizure acknowledgement after sending "seizure" (1000-10000 ms)

Shorttimer	Default (ms)	Description	Remark
S1	60	min. time for charge pulse (0-255 ms)
S2	0	min. time for dial-end signal (if P14<>0) (0-255 ms)
S3	0	send dial-end signal (if P14<>0) (0-255 ms)
S4	120	min. time for call-back signal or override signal via c-bit (0-255 ms)
S5	0	release acknowledge supervision on outgoing traffic (only if P4=7)
		0 without supervision
		1 with release acknowledge supervision (L4)
S6	4	Time after release forward, into the call charge pulses still are accepted	only DIUC64 LWVAR=F/G
		0 500 ms
		1-255 time in seconds
S7	0	time for clear back recognition on outgoing traffic (talk state) (only if P4=7)
		0 normal recognition time: 60ms
		1-255 delayed recognition time (time in seconds)
S8	0	rering after clear back of B-subscriber (on incoming traffic)
		0 line without rering signal
		1 rering signal ignore
		2 rering signal on a-bit (call to attendant)
		3 rering signal on c-bit (call to attendant)
S9	0	false answer signal on incoming traffic
		0 false answer signal is not to be sent
		1 false answer signal is to be sent
S10	0	line with call trace signal for incoming and outgoing traffic (nur wenn P4=7)
		0 line without call trace signal
		1 line with call trace signal
S11	0	answer supervision for outgoing traffic after end-of-dial
		0 without answer supervision
		1-225 with answer supervision (time in seconds)
S12	0	absence from seizure acknowledge on outgoing traffic
		0 keep seizure signal, after L7 blocking message to the system.
		1 after L7 send idle code, after P5 line available for new outgoing seizures.
S13	0	invalid bit combinations in talk state (incoming and outgoing traffic) (on outgoing traffic only if P4=0 oder P4=7)
		0 will be ignored
		1 will be considered as fault
S14	0	time for release recognition on incoming traffic after end-of-dial
		0 default recognition time: 100 ms
		1 delayed recognition time: 240 ms

Parameter	Default	Description		Remark
P1	2	dialing method after incoming seizure
		0	digit dialing (start of-pulsing immediately)
		1	MFV dialing (start of-pulsing via DH)
		2	MFC dialing (start.of-pulsing immediately)
P2	0	forced release from HICOM on incoming calls
		0	without forced release
		1	with forced release
		2	with forced release before and after answer : in case of fault and by clear back of system	only DIUC64 LWVAR=F/G
P3	0	seizure routing
		0	bothway
		1	outgoing
		2	incoming
P4	7	call charge indication on outgoing calls
		0	call charge receive abbb=11
		1	call charge receive abbb=01 (signalling without answer and backward release)
		3	call charge receive abbb=00
		6	call charge receive abbb=10
		7	no call charge receive
		8	call charge pulses on c-bit after answer
		9	call charge pulses on c-bit before and after answer
		16	call charge send abbb=11	only DIUC64 LWVAR=F/G
		32	call charge send and receive abbb=11	only DIUC64 LWVAR=F/G
P5	24	reseizure lookout time outgoing
		1-255	multiple of 250 ms
P6	0	outgoing dial tone supervision
		0	no supervision
		1	supervision
P7	90	answer supervision at outgoing calls
		0	no supervision
		1-255	supervision
P8	0	call charge simulation with answer from line
		0	no charge simulation
		1	with charge simulation with answer
P9	0	override signalling on incoming traffic
		0	line without override signal
		1	call to attendant on a-bit
		2	call to attendant on b-bit
		3	override on a-bit ignore
		4	override on b-bit ignore
		5	override on a-bit (begin and end recognition)
		6	override on b-bit (begin and end recognition)
		7	call to attendant on c-bit (only begin recognition)
		8	automatic override 2.5s after end-of-dial
		9	automatic call to attendant 2.5s after end-of-dial
		10	override on a-bit (only begin recognition)
		11	override on b-bit (only begin recognition)
P10	1	forced release from CO on outgoing calls
		0	without forced release
		1	with forced release
P11	0	answer procedure for collect call with answer subscriber B
		0	send normal signal to CO
		1	answer pulse (L2), finish char. (L3) send message to CO
		2	message to CO if ready for collect call answer pulse (L2), finish char. (L3) send message to CO, if not ready for collect call
P12	0	answer from line send to DH
		0	answer from line send to DH
		1	answer from line not send to DH
P13	0	dialing pulse (only if P1=0)
		0	dialing on a-bit
		1	dialing on b-bit
P14	0	end of dial / others
		0	without end of dial
		1	with end of dial (ab bb = 10)
		2	without end-of-dial, for use with ITALTE- CO, during the put-in-servce-procedure a received 00-signal from line will be respond with 10-idle code, not processed like a wrong line signal	only DIUC64 LWVAR=F/G
		3	without end-of-dial, during the put-in-servce-procedure send blocking signal 11 to line until incoming seizure 00 from line can be processed - for bothway or incoming directed trunks	only DIUC64 LWVAR=F/G     only if P3=0/2

Longtimer	Default (ms)	Description	Remark
L1	5000	release acknowledgement supervision after forward release (2000-20000 ms)
L2	1000	pause between answer and backward release (collect call) ( only for P11=1 or 2) (1000-10000 ms)
L3	2000	pause between backward release and answer (collect call) ( only for P11=1 or 2) (1000-10000 ms)
L4	150	send time for short pulses (120-180 ms)
L5	600	send time for long pulses (480-720 ms)
L6	80	min. receive time for short pulses (60-100 ms)
L7	300	max. receive time for short pulses (200-400 ms)

Shorttimer	Default (ms)	Description	Remark
S1	0	reserve
S2	0	reserve
S3	0	reserve
S4	0	reserve
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve

Parameter	Default	Description		Remark
P1	0	dialing method
		0	digit dialing
		1	MFV dialing
		2	MFC dialing
P2	0	reserve
P3	0	seizure routing
		0	bothway
		1	outgoing
		2	incoming
P4	0	reserve
P5	24	reseizure lookout time outgoing
		1-255	multiple of 250 ms
P6	0	outgoing dial tone supervision
		0	no supervision
		1	supervision
P7	90	answer supervision on outgoing calls
		0	no supervision
		1-255	supervision
P8	0	reserve
P9	0	reserve
P10	0	reserve
P11	1	answer procedure for collect call
		0	normal answer signal to CO
		1	answer/clear back/answer to CO
		2	answer to CO if ready for collect call
P12	0	reserve
P13	0	reserve
P14	0	reserve

Longtimer	Default (ms)	Description	Remark
L1	200	time for flash or ground trunk (60-500 ms)
L2	10000	supervision of subsequent ringing before answer in incoming traffic (4000-15000 ms)
L3	100	gap recognition time for release (16-200 ms)
L4	400	- delay for through-connection of speech path - delay for current supervision after answer in incoming traffic - minimum time for answer (100-2000 ms)
L5	100	minimum time for for change resp. rechange of polarity recognition (16-200 ms)
L6	125	minimum time for ring recognition (100-500 ms)
L7	5000	minimum time for idle current supervision (100 - 30000 ms)

Shorttimer	Default (ms)	Description	Remark
S1	70	min. time for charge impulse (40-255 ms)
S2	90	min. time for charge pulse pause (40-255 ms)
S3	0	reserve
S4	0	ANI - A-number identification procedure (incoming traffic)
		0 not activated
		1 between the 1st. and 2nd Ring (only if P14=3)
		2 ANI with Pre-seizure before 1st. ring (set L6>125ms) (only if P14<>3)
S5	0	Calling Party Release Control
		0 with Aufschalten_beginn Calling Party Release Control will be not activated
		1 with Aufschalten_beginn Calling Party Release Control will be activated
S6	0	answer procedure for collect calls (incoming traffic)
		0 normal answer loop
		1 1 sec. answer loop; loop interruption (S7); loop again
		2 for authorized extensions: normal answer loop for unauthorized extensions: 1 sec. answer loop; loop interruption (S7); loop again
S7	0	loop interruption in the collect call procedure
		n loop interruption (in multiples of 100ms)
S8	90	answer supervision in outgoing traffic (will be stoped after answer or with the first charge pulse)
		0 without answer supervision
		1-255 answer supervision in seconds (only if P7=2)
S9	0	reanswer supervision (outgoing traffic) the called party can answer again in outgoing traffic
		0 without disconnect supervision
		1-255 reanswer supervision in seconds (only if P7=2)
S10	6	reseizure guard time in seconds after outgoing call (1000-10000 ms)
S11	6	reseizure guard time in seconds after incoming call (1000-10000 ms)
S12	0	call time limit
		0 no limit
		1-255 maximum call time (multiple of 30 sec.)
S13	0	very Low loop resistance in the begin of an outgoing call
		0 8 ms
		1 350 ms
S14	0	delayed activation of line supervision
		0 1 sec
		1 36 ms

Parameter	Default	Description		Remark
P1	0	charge pulse
		0	without charge pulse
		1	with 12 kHz or 16 kHz charge pulse
		2	reversal pulse
		3	12 kHz answer pulse
		4	wink answer
P2	0	ground pulse to CO
		0	grounding of one wire
		1	grounding of both wires
P3	1	gap recognition in incoming traffic
		0	without supervision
		1	forward release recognition
P4	0	change of polarity recognition in incoming calls
		0	no supervision
		1	Forward release recognition ( through change of polarity)
P5	1	gap recognition in outgoing traffic
		0	without supervision
		1	Backward release recognition
P6	1	outgoing dial tone supervision
		0	no supervision
		1	supervision
P7	2	Change of polarity recognition in outgoing calls
		0	no supervision
		1	backward release recognition (through change of polarity)
		2	answer through change of polarity, Backward release recognition through rechange of polarity
P8	1	line supervision
		0	no supervision
		1	supervision ( P3, P4, P5 or P7=1 or P14)
P9	2	ring recognition hardware (TMCOW version and edition number-dependent parameter)
		0	ring recognition through narrow band circuit (13-33 Hz)
		1	ring recognition through TRIC (23-80 Hz)
		2	ring recognition through broad band circuit (13-80 Hz)
P10	0	ESB for TRIC-Integrated Circuit
		0	Default-value from LW-table
		<>0	TRIC-CMD
P11	0	TRIC-Power-Mode
		0	Power-Down-Mode
		1	Power-Up-Mode
P12	6	transmission parameter board and country dependent parameter (SICOFI-table)
P13	0	delay of 1 digit by DP-dialing
		0	no delay
		1	delay = 1s
P14	0	outgoing seizure procedure and idle current supervision
		0	loop start without idle current supervision
		1	loop start with idle current supervision (L7)
		2	ground start without idle current supervision (earth calling)
		3	(only if S4=0) ANI - Pre-seizure by short feed Interruption and current supervision (L7)

Longtimer	Default (ms)	Description	Remark
L1	300	min. release time (interrupt from CO) (48-1200 ms)
L2	600	potential gap on backward release (P4=1) or on release acknowledgement (P4=2) (400-800 ms)
L3	1000	delay release collect call (0-1000 ms)
L4	2000	interrupt release collect call (0-2000 ms)
L5	10000	dalaying on message signalling (only if P11=3) (1000-32000 ms)
L6	200	forced pause between seizure acknowledgement and start-of-pulsing (for USA) (0-400 ms)
L7	152	dial queue supervision (0-400 ms)

Shorttimer	Default (ms)	Description	Remark
S1	32	reversal on time for seizure acknowledgement (20-100 ms)
S2	32	reversal on time for start-of-pulsing (20-100 ms)
S3	32	reversal on time for end-of-dial (20-100 ms)
S4	32	potential gap on seizure acknowledgement
S5	32	potential gap on start-of-pulsing signal (20-100 ms)
S6	32	potential gap on end-of-dial (20-100 ms)
S7	30	noise suppression on incoming seizure (20-100 ms)
S8	20	min. dial pulse length and time for noise suppression (0-100 ms)
S9	72	dial pulse tolerance (20-100 ms)
S10	80	min. time for CO signaling (20-100 ms)
S11	12	min. dial pause and time for noise suppression (0-100 ms)
S12	70	min. time between incoming seizure and sending the seizure acknowledgement (20-100 ms)
S13	0	malicious call tracing / release from PSTN
		0 line without malicious call tracing signal / release from PSTN will be accepted
		1 line with malicious call tracing signal (reverse - 300ms - reverse) / release from PSTN will be accepted
		2 line without malicious call tracing signal / release from PSTN in talk state will be ignored
		3 line with malicious call tracing signal (reverse - 300ms - reverse) / release from PSTN in talk state will be ignored
S14	1	level in dial state
		0 level in dial state is like in talk state (level 0)
		1 another level in dial state than in talk state possible (level 1 and 2 - depends on the SICOFI-block)

Parameter	Default	Description		Remark
P1	1	seizure acknowledgement (Only used if COP-Parameter SACK is configured)
		0	feeding gap until start-of-dialing
		1	reversal temporary (S1)
		2	reversal permanent
		3	feeding gap (S4)
P2	1	start-of-dialing (Only used if COP-Parameter SDL is configured)
		0	feeding gap (S5)
		1	reversal temporary (S2)
		2	reversal permanent
		3	feeding gap until start-of-dialing
P3	0	End-of-dial (Only used if COP-Par. EOD is configured)
		0	feeding gap (S6)
		1	reversal temporary (S3)
		2	reversal permanent
		3	no proceed End-of-dial
P4	0	backward release
		0	reversal
		1	gap (L2)
		2	forward release acknowledge with send feeding gap (L2) first, than reversal backward realease only with reversal
P5	2	open-circuit potential
		1	plus on a-wire
		2	minus on a-wire
P6	2	dialing method
		0	IWV frequency 10Hz (S8, S10)
		1	IWV frequency 20Hz
		2	DTMF
		3	MFC-R2
P7	4	flash or ground signaling of CO in case of busy
		0	override by flash from CO
		1	call to ATND by flash from CO
		2	override by ground key (<3S)
		3	call to ATND by ground key (<3S)
		4	line without override
		5	automat. override with wrong message	reversal - 150 ms - back-reversal ignore flash or ground key
		6	automat. override without wrong message	ignore flash or ground key
P8	0	Inhibit
		0	A/B potential free
		1	A/B potential reversed
		2	A/B potential same as for open circuit
P9	90	release supervision from CO
		0	no supervision
		1-255	in seconds
P10	0	flash or ground signaling of CO (release B-STN)
		0	new seizure by flash from CO
		1	call to ATND by flash from CO
		2	call to ATND by ground key (<1S)
		3	ignore
P11	2	answer procedure
		0	normal answer (reversal of polarity)
		1	answer with release on Collect-Call: answer through reversal of polarity (L3), potential gab (L4), reanswer
		2	answer with release on Collect-Call (depending on the user authorization): answer through reversal of polarity (L3), potential gab (L4), reanswer
		3	delayed answer signaling
		4	answer with release on Collect-Call: answer through reversal of polarity (L3), inversal of polarity (L4), reanswer through reversal of polarity
		5	answer with release on Collect-Call (depending on the user authorization): answer through reversal of polarity (L3), inversal of polarity (L4), reanswer through reversal of polarity
P12	6	impedance and level definition
		0	BRA Brazilian
		6	BRA Brazilian
		8	RSA South African
		9	GBR Great Britain
		10-80	country dependent value
P13	0	voltage feeding supervision on the PSTN
		0	no voltage feeding supervision on the PSTN (feeding default value: 33V; voltage feeding value will be automatically determined by current measuring; nominal current: 20 mA)
		1	voltage feeding supervision on the PSTN; fixed voltage: -18V
		2	voltage feeding supervision on the PSTN; fixed voltage: -23V
		3	voltage feeding supervision on the PSTN; fixed voltage: -28V
		4	voltage feeding supervision on the PSTN; fixed voltage: -33V
		5	voltage feeding supervision on the PSTN; fixed voltage: -38V
		6	voltage feeding supervision on the PSTN; fixed voltage: -43V
		7	voltage feeding supervision on the PSTN; fixed voltage: -48V
		8	voltage feeding supervision on the PSTN; fixed voltage: -53V
P14	0	rering by flash from PSTN (between seizure and end-of-dial the flash from PSTN must be > (S8+S9) to recognition of flash)
		0	without rering
		1	with rering

Longtimer	Default (ms)	Description	Remark
L1	180	seizure detection for incoming calls (10-500 ms)
L2	2000	reseizure lookout time outgoing after outgoing seizure (200-5000 ms)
L3	1000	reseizure lookout time outgoing after incoming seizure (200-5000 ms)
L4	40	backward release acknowledgement on outgoing calls without call tracing or after forward release (40-1000 ms)
L5	5000	seizure acknowledgement supervision on outgoing calls (1-30000 ms)
L6	0	reserve
L7	0	reserve

Shorttimer	Default (ms)	Description	Remark
S1	100	min. acknowledge time for forward release after backward release on incoming calls (40-200 ms)
S2	120	acknowledgement of simultaneous seizure after outgoing seizure (10-250 ms)
S3	0	reserve
S4	0	reserve
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve

Parameter	Default	Description		Remark
P1	0	dialing method
		0	IWV- dial
		1	MFV- dial
P2	0	reserve
P3	0	seizure routing for transmission
		0	bothway
		1	outgoing
		2	incoming
P4	0	reserve
P5	0	reserve
P6	1	dial tone supervision for outgoing calls
		0	no supervision
		1	with supervision
P7	0	reserve
P8	0	call tracing on outgoing calls
		0	without
		2	with MTC line signal
P9	0	reserve
P10	0	reserve
P11	0	reserve
P12	0	reserve
P13	0	reserve
P14	0	reserve

Longtimer	Default (ms)	Description	Remark
L1	1000	seizure-acknowledge supervision-time (1000-30000 ms)	out
L2	30000	release guard supervision-time (1000-30000 ms)	out
L3	5000	alarm recognition-time (1000-30000 ms)	out/inc
L4	1000	blocking recognition-time (1000-30000 ms)	out
L5	1000	outgoing guard timer (1000-30000 ms)	out
L6	1000	delayed through connection on speech channel after answer only if P11 = 0 (ANI-request line signal is possible but will be ignored) (10-30000 ms) delayed through connection on speech channel after answer (10-30000 ms)	out   inc   for Kazakhstan : 10 ms
L7	1300/400	ANI-removal recognition-time (only if P11=1 or 2) (ANI-request line signal is possible and will be processed) (1000-30000 ms) default: 1300 ANI-removal sending time (1000-30000 ms) default: 400	out     inc

Shorttimer	Default (ms)	Description	Remark
S1	20	seizure recognition-time (10-255 ms)	inc
S2	200	release or clear forward recognition after answer (10-255 ms)	inc
S3	20	release guard recognition-time (10-255 ms)	out
S4	0	TSL refresh time before answer (should: 100, if P4 or P5=1) (10-255 ms)
S5	0	TSL refresh time after answer (should: 100, if P4 or P5=1) (10-255 ms)
S6	0	reserve
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve

Parameter	Default	Description		Remark
P1	0	type of dialing (incoming)
		0	pulse dialing
		2	MF dialing
P2	0	reaction to b_busy from line (outgoing)
		0	release
		1	end of dial (b_busy) message send to DH
P3	1	direction of seizure
		1	outgoing
		2	incoming
P4	0	TSL-refresh in outgoing trafic
		0	no refresh
		1	with refresh - time administrable in S4 and S5
P5	0	TSL-refresh in incoming traffic
		0	no refresh
		1	with refresh - time administrable in S4 and S5
P6	0	supervision of dial tone (outgoing traffic)
		0	no supervision
		1	supervision
P7	20	supervision of answer (outgoing traffic)
		0	no supervision
		1-255	multiples of 30 s.
P8	0	malicious call id. after sending clear forward (outgoing)
		0	no MCID
		1-255	multiples of 30 s. (with MCID: 4)
P9	20	release supervision time (outgoing)
		0	no supervision
		1-255	multiples of 30 s.
P10	0	reaction on receiving clear forward (incoming)
		0	send clear back line signal and release message to DH
		1	send "a hook on" message to DH used for bilateral calls
P11	0	ani-request line signal activate ani-codogram transmission (outgoing)
		0	no ani-request, line signal ani-request is possible but will be ignored from LW
		1	ani-request line signal is possible and will be processed (ani-request message send to DH immediately after answer from line)
		2	ani-request line signal is possible and will be processed (like 1 but after first answer > 2,8s ani-request message send to DH after answer removal from line)
		3	line without ani-request, line signal ani-request is not possible and will be processed like answer.
P12	0	busy override (incoming traffic)
		0	no busy override
		1	busy override
P13	0	line testing (outgoing traffic)
		0	no line testing
		1	line testing
P14	0	release-variant: output signal after receiving release message from DH
		0	LONIIS output signal: 11 - release forward (out) output signal: 00 - clear back (in)
		1	MGTS output signal: 00 - clear forward (out) output signal: 11 - seizure acknowledgement (in)

Longtimer	Default (ms)	Description	Remark
L1	1000	supervision-time for seizure-acknowledgement (1000-30000 ms)
L2	30000	supervision-time for release guard after release forward (1000-30000 ms)
L3	5000	recognition-time of faults (1000-30000 ms)
L4	1000	recognition-time of blocking (1000-30000 ms)
L5	1000	outgoing guard timer (1000-30000 ms)
L6	0	delay-time of through connection on speech channel (0-30000 ms)
L7	200	min. sending time of b-busy in case of simulated manual busy override (0-3000 ms)

Shorttimer	Default (ms)	Description	Remark
S1	20	recognition-time for incoming seizure (10-255 ms)
S2	150	recognition-time for release forward after answer (10-255 ms)
S3	20	recognition-time for release guard (10-255 ms)
S4	0	reserve
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve

Parameter	Default	Description		Remark
P1	0	type of dialing (incoming traffic)
		0	pulse dialing
		2	MF dialing
P2	0	reaction to b-busy from line (outgoing traffic)
		0	release
		1	end of dial (b-busy) message to DH
		2	without end-of-dial (b-busy) message to DH
P3	1	direction of seizure
		1	outgoing
		2	incoming
P4	0	ring after B-free (outgoing traffic)
		0	DH controlled transmission of ring request and ring request removal signaling dependent on P10 (default)
		1	automatic ring request transmission (no DH control)
P5	20	supervision of end of dial (outgoing traffic)
		0	no supervision
		1-255	multiples of 30 s.
P6	0	supervision of dial tone (outgoing)
		0	no supervision
		1	supervision
P7	6	supervision of answer (outgoing traffic)
		0	no supervision
		1-255	multiples of 30 s.
P8	0	ring after b-free (incoming traffic)
		0	LW ignores ring request signals (automatic ring) (default)
		1	DH will be informed about recognition of 1 st ring but not about ring removal
		2	DH will be informed about recognition of ring request and ring request removal (line signal controlled ring)
P9	0	rering after b - on-hook (incoming traffic)
		0	DH will be informed about recognition of 1st rering but not about rering removal
		1	DH will be informed about recognition of rering and rering removal (line signal controlled rering)
P10	0	kind of ring and rering signals (outgoing traffic/incoming traffic)
		0	periodically pulsed ring and rering (default)
		1	fixed signals for ring and rering
P11	0	reaction to AUSLOESEN from DH in dial state (incoming traffic)
		0	b-busy transmission (default)
		1	no change in line transmission
P12	1	manual busy override (incoming traffic)
		0	no busy override (line signal ignored)
		1	simulated (time-controlled) busy override (line signal ignored) (default)
		2	DH will be informed about recognition of 1st reset but not about reset removal
		3	DH will be informed about recognition of reset and reset removal (line signal controlled busy override)
P13	0	line testing (outgoing traffic)
		0	no line testing
		1	line testing
P14	0	rering after reset and b-on hook (incoming traffic)
		0	LW ignores rering request signals (default)
		1	DH will be informed about recognition of 1st rering but not about rering removal
		2	DH will be informed about recognition of rering request and rering request removal (line signal controlled rering)

Longtimer	Default (ms)	Description	Remark
L1	600	transmission time of long pulses (10-30000 ms)	out/inc
L2	300	min. recognition time of long pulses (10-30000 ms)	out/inc
L3	1700	min. recognition time of blocking (10-30000 ms)	out/inc
L4	240	min. pause between 2 sending signals (10-30000 ms)	out/inc
L5	300	supervision of glare seizure (10-30000 ms)	out
L6	400	supervision of glare release (10-30000 ms)	out
L7	2000	supervision of seizure acknowledge (10-30000 ms)	out

Shorttimer	Default (ms)	Description	Remark
S1	150	transmission time of short pulses (1-255 ms)	out/inc
S2	100	min. recognition time of short pulses (1-255 ms)	out/inc
S3	40	min. recognition time of dial pulses (1-255 ms)	inc
S4	200	min. recognition time of interdigit time (S2+S4) (1-255 ms)	inc
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	transmission of seizure acklowledge 0 no transmission (default) 1 transmission	inc
S9	0	supervision of seizure acknowledge 0 no supervision (default) 1 supervision with L7	out
S10	0	recognition of dial pulse during interdigit time 0 digit is invalid (0F)(default) (TF-signaling for Hungary) 1 digit is valid (TF-signaling for Brasil FURNAS)	inc
S11	0	activation of calling party RLC with manual override 0 no (default) 1 activation	out
S12	0	reserve
S13	0	reserve
S14	0	reserve

Parameter	Default	Description		Remark
P1	0	type of dialing		out/inc
		0	IWV
		1	DTMF
		2	MFC-R2
P2	9	supervision of release guard after clear forward		out
		0	no supervision
		1-255	multiples of 10 s (default: 9 ≅90 sec.)
P3	0	direction of seizure
		0	bidirectional (default)
		1	outgoing
		2	incoming
P4	10	delay of clear forward after clear back		out
		0	send clear forward promptly
		1-255	multiples of 10 s (default: 10 ≅100 sec.)
P5	0	outgoing guard time		out/inc
		0	6s (default)
		1-255	multiples of 250ms
P6	0	supervision of dial tone		out
		0	no supervision (default)
		1	supervision
P7	9	supervision of answer		out
		0	no supervision
		1-255	multiples of 10 s (default: 9 ≅90 sec.)
P8	0	operator signals (override, rering)		out
		0	line with no operator signals (default)
		1	line with operator signals
P9	0	override		inc
		0	ignore override from line (no automatic override) (default)
		1	attendant intercept
		3	ignore override (automatic override)
		5	manual override (calling party RLC)
		6	manual override, no sending of answer and clear back when B on-hook (first party RLC)
P10	0	rering		inc
		0	line with no rering (default)
		1	line with rering
P11	0	supervision of clear forward after clear back		inc
		0	90s (default); after T/O blocking to DH, wait for release
		1-255	multiples of 10 s; after T/O idle after outgoing guard time
P12	0	startup		outgoing/bothway
		0	idle (default)
		1	seizure with release
P13	0	out of service		incoming/bothway
		0	no line signal (default)
		1	continuous line signal
P14	0	test procedure(seizure acknowledge or release guard fails to come)		out
		0	no test procedure (default)
		1-255	multiples of 10s: time between testcycles

Longtimer	Default (ms)	Description	Remark
L1	300	min. time interval between reception and transmission of line signals (100-600 ms)
L2	900	supervision for simultaneous on hook signal during transmission of clear up (100-900 ms)
L3	300	min. time interval between transmission of two pulsed line signals (100-600 ms)
L4	3000	supervision of release guard signal (1-32000 ms)
L5	5000	supervision time for operator signals: rering, ringback, forced break and return-call-to-operator signal 0 no supervision (only one message to system) 1-30000 ms supervision time (one message to system per interval)
L6	0	reserve
L7	0	delay of speech path through connection after first answer for incoming traffic 0 no delay 4-3000 ms delay time of speech path through connection

Shorttimer	Default (ms)	Description	Remark
S1	0	reserve
S2	0	reserve
S3	0	reserve
S4	0	reserve
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	control of level attenuation
		0 = control of level attenuation off
		1 = control of level attenuation on
S9	1	putting incoming or bothway directed line into service 0 no line signal 1 prolongated blocking line signal for 2 s
S10	1	putting outgoing directed line into service 0 no line signal 1 repetitive release signal (once) without line supervision 2 repetitive release signal (corr. P2) with line supervision
S11	0	line supervision in talk state (depends on P4) 0 without supervision 1 with supervision
S12	0	reserve
S13	0	reserve
S14	0	reserve

Parameter	Default	Description		Remark
P1	1	dialling method
		0	rotary dialling ( with proceed-to-send: short pulse; immediately)
		1	no rotary dialling without proceed-to-send
		2	no rotary dialling (with proceed-to-send: short pulse; immediately)
		3	no rotary dialling (with proceed-to-send: short pulse; under DH-control)
		4	no rotary dialling (with proceed-to-send: long pulse; under DH-control)
P2	3	release repetition on outgoing side
		0	no release repetition
		1-254	release repetition with restricted no. of release repetition attempts
		255	release repetition with unrestricted no. of release repetition attempts
P3	0	signalling direction
		0	no release repetition
		1	outgoing directed
		2	incoming directed
P4	60	line release supervision time
		0	no timer assigned
		1-255	line release supervision time in minutes
P5	2	guard time before new outgoing seizure
		1-255	guard time in seconds
P6	0	dial tone supervision
		0	no dial tone supervision
		1	dial tone supervision
P7	90	answer supervision in outgoing traffic
		0	no answer supervision
		1-255	answer supervision time in seconds
P8	3	recognition of operator signals: (rering, ringback, forced break)
		1-10	number of pulses
P9	3	transmission of operator signals: (rering, ringback, forced break)
		1-10	number of pulses
P10	0	forced break recognition
		0	no forced break recognition
		1	forced break recognition
P11	0	recognition of rering or ringback
		0	no recognition
		1	recognition of rering and ringback
		2	recognition of rering
		3	recognition of ringback
P12	0	return-call-to-operator
		0	no return-call-to-operator recognition/transmission
		1-10	return-call-to-operator transmission by sending 'n' pulse series on incoming trunk
		n>0	return-call-to-operator recognition on outgoing trunk
P13	0	echo suppression of 2600 Hz signals
		0	reception during transmission is evaluated
		1	reception during transmission is suppressed
P14	0	line criteria before anser (after proceed-to-send)
		0	none
		1	reserve
		2	initial code acknowledge and reached-to-called-party