154.6.6 Appendix 2, Part 6: Initblocks 101 till 115, 119 till 123


Long timer	Default (ms)	Description	Remark
L1	800	sending time for release forward impulse (200-4000 ms)
L2	800	sending time for release backward impulse (200-4000 ms)
L3	0	reserve
L4	0	reserve
L5	10000	max. recognition time for release (200-15000 ms)
L6	500	time of ignore line signal after release from system by put into service
L7	0	reserve


Short timer	Default (ms)	Description	Remark
S1	220	recognition time for seizure type 2 (40-252ms)
S2	180	recognition time for seizure type 1 seizure acknowledge, answer (40-240ms)
S3	100	max. recognition time for dial pulse (40-240ms)
S4	100	recognition time for end-of-digit (40-240ms)
S5	70	sending time for seizure type 2 or 3 (60-252ms)
S6	250	sending time for seizure type 1 (24-255ms)
S7	70	sending time for test seizure pulse (24-240ms)
S8	40	sending time for seizure acknowledge pulse (24-200ms)
S9	0	reserve
S10	0	reserve
S11	100	sending time for answer pulse (24-200ms)
S12	200	min. distance between 2 sending signals, seizure acknowledge and answer (40-252ms)
S13	40	time for glare seizure (12-100ms)
S14	0	Time between receive seizure and send seizure acknowledgement 0: send seizure acknowledgement controlled by DH 1-255: Time between seizure and send seizure acknowledge (plus LW-delay from 40 ms)	If S14<>0, than DH-Timer: CHA-DTIM1:TYPEDH=TIE,RESET4=20;


Parameter	Default	Description				Remark
P1-high*	0	2 / 4 Draht voice				only 4 wire voice available
		0	4 Draht voice
		1	2 Draht voice (Gabel)
P1-low*	0	E&M - type
		0	type IA (V)
		1	DC5
		2	type I
		3	type II
		4	HL / LL with type I			HL: high level supervion
		5	HL / LL with type IA (V)			LL: low level supervision
P2	0	Impedance-Index
			level A->D [dB]	level D->A [dB]	A / μ-law
		0	-3,5	-3,5	A	4 wire standard level C13
		1	-1,5	-1,5	A	Australia old
		2	+0,5	-4,5	A	GBR
		3	0	-6	m	USA
		4	-4,5	-2,5	A	GUS
		5	-2,5	-4,5	A	BRD
		6	0	0	A	Australia new
		7	-7,0	0	A	standard level for 4-2 wire-converter with (-3,5/-3,5)
		8	0	-8,5	A	ITL railway + EVU
		9	+7	-16,0	A	Korea, Japan
		10	+4,3	-13,0	A	BRD, GUS, UNG C11-FDM
		11	+3,3	-12,0	A	GUS C11
P3-high*	0	low level-controling (TP-low level)				only if P1-low = 4 or 5
		0	only line supervision			TP on ground = no alarm
		1	line supervision with going in service periodical			TP on ground = no alarm
		2	with alarm measuring			TP on ground = no alarm
		3	only line supervision with TP invert			TP on ground = alarm
		4	line supervision with going in service periodical with TP invert			TP on ground = alarm
		5	with alarm measuring with TP invert			TP on ground = alarm
P3-low*	0	Normal / Inversmode				only valid for high level-line
		0	Normal Signaling (Idle: M=OFF / E=OFF)
		1	Inverse Signaling at M- and E-wire (Idle: M=ON / E=ON)
		2	Inverse Signaling only at E-wirer (Idle: M=OFF / E=ON)
		3	Inverse Signaling only at M-wire (Idle: M=ON / E=OFF)
P4	0	reserve
P5-high*	0	Quad-SICOFI Version				Parameter depends from version of QUAD-SICOFI
		0	Version not equal V2.3 (switched on only at talk-state)
		1	Version V2.3 (switched on always)
P5-low*	4	Last Look (LL)
		0-15	multiple of 1ms
P6-high*	0	reaction of pulse dialing at recognition of line signal				out
		0	continue pulse dialing
		1	suppress pulse dialing
P7	0	reserve
P8	0	reserve
P9	0	reserve
P10	0	reserve
P11	0	reserve
P12	0	reserve
P13	0	reserve
P14	0	Highway / time slot release triggered by event
		0	Release of time slots / highways by receiving the event DB_EE_E_AUSLOESEN message			Works via COP ACKB and ACKF
		1	Release of time slots / highways by receiving the event DB_EE_E_KOMMEND_BTB message			This parameter must be set if the COP ACKB and/or ACKF are not set!

* High und low byte values are hexadecimal, which have to be converted into decimal to get the corresponding parameter value.

Example: Parameter P3: high byte: 2, low byte: 0 ==> P3[Hex]=20 --> P3[Dec]=32

(102): DB_AM_DEV_QSTF8: TSC8


Longtimer	Default (ms)	Description	Remark
L1	0	reserve
L2	0	reserve
L3	0	reserve
L4	0	reserve
L5	0	reserve
L6	0	reserve
L7	0	reserve


Shorttimer	Default (ms)	Description	Remark
S1	0	reserve
S2	0	reserve
S3	0	reserve
S4	0	reserve
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve


Parameter	Default	Description	Remark
P1	0	reserve
P2	0	reserve
P3	0	reserve
P4	0	reserve
P5	0	reserve
P6	0	reserve
P7	0	reserve
P8	0	reserve
P9	0	reserve
P10	0	reserve
P11	0	reserve
P12	0	reserve
P13	0	reserve
P14	0	reserve

(103): DB_AM_DEV_QSEMCONT: QSEMCONT


Longtimer	Default (ms)	Description	Remark
L1	300	minimal transmit time for release (30 - 2000ms)
L2	180	recognition tie for forward release, maximal time for break (DP) (10 - 2000ms)
L3	180	recognition time for backward signals (10 - 2000ms)	If P6=0: t≥L3: backward release t<L3: backward impuls If P6=1: t≥L3: end of dial, backward release
L4	0	reserve
L5	0	reserve
L6	0	reserve
L7	0	reserve


Shorttimer	Default (ms)	Description	Remark
S1	40	time for glare seizure (10-255ms)
S2	60	transmit time for backward pulsed signals (e.g.: seizure acknowledge, answer, etc.) (10-255ms)	only if P6=0
S3	80	maximal recognition time for make (DP) = minimal recognition time for interdigit pause (10-255ms)
S4	0	reserve
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve


Parameter	Default	Description				Remark
P1-high*	0	2 / 4 Wire voice				only 4 wire voice available
		0	4 Wire voice
		1	2 Wire voice (hybrid)
P1-low*	0	E&M - type
		0	type IA (V)
		1	DC5
		2	type I
		3	type II
		4	HL / LL with type I			HL: high level supervion
		5	HL / LL with type IA (V)			LL: low level supervision
P2	0	Impedance-Index
			evel A->D [dB]	level D->A [dB]	A / μ-law
		0	-3,5	-3,5	A	4 wire standard level C13
		1	-1,5	-1,5	A	Australia old
		2	+0,5	-4,5	A	GBR
		3	0	-6	m	USA
		4	-4,5	-2,5	A	GUS
		5	-2,5	-4,5	A	BRD
		6	0	0	A	Australia new
		7	-7,0	0	A	standard level for 4-2 wire-converter with (-3,5/-3,5)
		8	0	-8,5	A	ITL railway + EVU
		9	+7	-16,0	A	Korea, Japan
		10	+4,3	-13,0	A	BRD, GUS, UNG C11-FDM
		11	+3,3	-12,0	A	GUS C11
P3-high*	0	low level supervision (TP- low level)				only if P1-low = 4 or 5
		0	only line supervision			TP on ground = no alarm
		1	line supervision with going in service periodical			TP on ground = no alarm
		2	with alarm measuring			TP on ground = no alarm
		3	only line supervision with TP invert			TP on ground = alarm
		4	line supervision with going in service periodical with TP invert			TP on ground = alarm
		5	with alarm measuring withTP invert			TP on ground = alarm
P3-low*	0	Normal / Inversmode				only valid for highpegel-line
		0	Normal Signaling (Idle: M=OFF / E=OFF)
		1	Inverse Signaling at M- and E-wire (Idle: M=ON / E=ON)
		2	Inverse Signaling only at E-wirer (Idle: M=OFF / E=ON)
		3	Inverse Signaling only at M-wire (Idle: M=ON / E=OFF)
P4	0	reserve
P5-high*	0	Quad-SICOFI Version				Parameter depends from version of QUAD-SICOFI
		0	Version not equal V2.3 (switched on only at talk-state)
		1	Version V2.3 (switched on always)
P5-low*	4	Last Look (LL)
		0-15	multiple of 1ms
P6-high*	0	reserve
P6-low*	0	Protocol
		0	E&M continuous universal or CEPT-L1
		1	E&M continuous loop converter
P7	0	reserve
P8	0	reserve
P9	0	reserve
P10	0	reserve
P11	0	reserve
P12	0	reserve
P13	0	reserve
P14	0	reserve

* High und low byte values are hexadecimal, which have to be converted into decimal to get the corresponding parameter value.

Example: Parameter P3: high byte: 2, low byte: 0 ==> P3[Hex]=20 --> P3[Dec]=32

(104): DB_AM_DEV_EMCONT2: EMCONT2


Longtimer	Default (ms)	Description	Remark
L1	5000	maximum recognition time for seizure acknowledge pulse 40 - 10000 ms	out
L2	180	maximum recognition time for release guard 40 - 500 ms	out when P8-high=1 -> ( L2 > L4)
L3	120	minimum recognition time for clear forward or release backward 100 - 600 ms	out/inc
L4	90	minimum transmission time for release guard 40 - 500 ms	inc when P8-high=1 -> (L2 > L4)
L5	100	minimum recognition time for seizure 20 - 500 ms	inc when P6-low=1-> (L5 > S3)
L6	200	minimum recognition time for release acknowledge 100 - 1000 ms	out
L7	400	minimum transmission time for answer 20 - 1000 ms	inc


Shorttimer	Default (ms)	Description	Remark
S1	80	minimum recognition time for seizure acknowledge pulse 40 - 200 ms	out
S2	100	minimum transmission time for clear backward before release guard 20 - 255 ms	inc
S3	30	supervision time for glare seizure	out
		0 2,4 seconds	inc
		4-255 time in ms	inc
S4	140	transmission time for Wink start	inc
		0: 300ms impulse
		60 - 255: time in ms
S5	100	minimum transmission time for delay dial 20 - 255 ms	inc
S6	60	minimum recognition time for metering pulse 20 - 255 ms	out
S7	10	time to ignore pulsed dialing on incoming side after wink start or delay dial signal	inc
		0: not ignore
		1 - 100: time to ignore in ms
S8	0	conversation supervision	out/inc
		0: endless
		1 - 255: supervision time in 30 s.-steps
S9	120	answer supervision in case of outgoing directed traffic	out
		0: no answer supervision
		1 - 255: answer supervision in seconds
S10	0	guard time before new outgoing seizure	out/inc
		0: 500 ms
		1 - 255: guard time in 1 s.-steps
S11	0	allowed time for override impulse	inc
		0 : without override
		1: override without time limit
		2 - 60: time in 1 s.-steps
S12	1	retry timer for active phase of test procedure 1 - 10: time in 1 s.-steps	out only when P9-low=1
S13	60	retry timer for passive phase of test procedure 1 - 255	out only when P9-low=1
S14	1	supervision time for clear forward	inc (Blocking or alarm recognition)
		0: no supervision
		1 - 255: supervision time in 1 s.-steps


Parameter	Default	Description				Remark
P1-high*	0	2 / 4 wire voice				only 4 wire voice implemented
		0	4 wire voice
		1	2 wire voice (Hybrid)
P1-low*	0	E&M - type
		0	type IA (V)
		1	DC5
		2	type I
		3	type II
		4	HL / LL with type I			HL: high level supervion
		5	HL / LL with type IA (V)			LL: low level supervision
P2	0	Impedance-Index
			level A->D [dB]	level D->A [dB]	A / μ-law
		0	-3,5	-3,5	A	4 wire standard level C13
		1	-1,5	-1,5	A	Australia old
		2	+0,5	-4,5	A	GBR
		3	0	-6	m	USA
		4	-4,5	-2,5	A	GUS
		5	-2,5	-4,5	A	BRD
		6	0	0	A	Australia new
		7	-7,0	0	A	standard level for 4-2 wire-converter with (-3,5/-3,5)
		8	0	-8,5	A	ITL railway + EVU
		9	+7	-16,0	A	Korea, Japan
		10	+4,3	-13,0	A	BRD, GUS, UNG C11-FDM
		11	+3,3	-12,0	A	GUS C11
P3-high*	0	Low level supervision control (TP- low level)				only when P1-low = 4 or 5
		0	only line supervision			TP on ground = no alarm
		1	line supervision with going in service periodical			TP on ground = no alarm
		2	with alarm measuring			TP on ground = no alarm
		3	only line supervision with TP invert			TP on ground = alarm
		4	line supervision with going in service periodical with TP invert			TP on ground = alarm
		5	with alarm measuring withTP invert			TP on ground = alarm
P3-low*	0	Normal / Inverse mode
		0	Normal Signalling (Idle: M=OFF / E=OFF)
		1	Inverse Signalling for M- and E-wire (Idle: M=ON / E=ON)
		2	Inverse Signalling only for E-wire (Idle: M=OFF / E=ON)
		3	Inverse Signalling only for M-wire (Idle: M=ON / E=OFF)
P4	0	reserve
P5-high*	0	Quad-SICOFI Version				Parameter depends on QUAD-SICOFI-Version
		0	Version different from V2.3 (on only in talk state)
		1	Version V2.3 (always on)
P5-low*	4	Last Look (LL
		0-15	(... x 1ms)
P6-high*	0	reserve
P6-low*	0	Seizure acknowledge				out/inc
		0	Immediate dial
		1	Delay dial
		2	Wink start
		3	Continuous signal
P7-high*	0	dial tone recognition				out
		0	no dial tone recognition
		1	dial tone recognition
P7-low*	0	signalling direction				out/inc
		0	bothway directed (glare seizure: priority of incoming seizure)
		1	outgoing directed
		2	incoming directed
		3	bothway directed (glare seizure: release of line)
P8-high*	0	release guard as line signal				out/inc
		0	without release guard as line signal
		1	with release guard as line signal
P8-low*	0	special clear backward with pseudo-answer and backward release on incoming side before answer				inc
		0	not used
		1	after called subscriber busy
		2	after release from DH
		3	after called subscriber busy or release from DH
P9-high*	0	metering pulse recognition				out
		0	no metering pulse recognition
		1	metering pulse recognition
P9-low*	0	test procedure				out
		0	no test procedure
		1	with test procedure
P10-high*	0	blocking as line signal, if bothway or incoming directed traffic				out/inc
		0	without blocking as line signal
		1	with blocking as line signal
P10-low*	1	answer as line signal				out/inc
		0	without answer as line signa
		1	with answer as line signal
P11-high*	0	dialing method				out/inc
		0	DP	(dial pulse)
		1	DTMF	(multifrequency)
		2	MFC-R2
P11-low*	0	metering pulse simulation by answer				out
		0	without simulation
		1	with simulation
P12	28	number of override impulses				out/inc
		0 - 50	number of impulses
P13-high*	0	supervision time for ready line signal				out
		0	no supervision
		1-15	supervision time in 1 s-steps
P13-low*	0	supervision time for clearback line signal				out
		0	no supervision
		1-15	supervision time in 1 s-steps
P14	0	dial pulse recognition on incoming side after answer				inc
		0	no recognition after answer
		1	recognition after answer

* High und low byte values are hexadecimal, which have to be converted into decimal to get the corresponding parameter value.

Example: Parameter P3: high byte: 2, low byte: 0 ==> P3[Hex]=20 --> P3[Dec]=32

(105): DB_AM_DEV_EMDISC2: EMDISC2


Longtimer	Default (ms)	Description	Remark
L1	5000	supervision time for start dial signal after seizure (40 - 10000 ms)	out
L2	625	transmission time for long impulse (200 - 2000 ms)	out
L3	300	transmission time for long pause (clear back pulse train) (100 - 1000 ms)	inc
L4	270	minimum recognition time for long impulse (S3+S4+L4) (100 - 1000 ms)	inc
L5	2000	maximum recognition time for long impulse (L5 > S3+S4+L4) (400 - 5000 ms)	inc
L6	400	recognition time for long pause (clearback puls train) (50 - 1000 ms)	out
L7	0	reserve


Shorttimer	Default (ms)	Description	Remark
S1	100	transmission time for short impulse 40 - 250 ms	out/inc
S2	100	transmission time for short pause 40 - 250 ms	inc
S3	70	minimum recognition time for short impulse 20 - 250 ms	out/inc
S4	60	maximum recognition time for short impulse S3 < t < S3+S4 40 - 250 ms	out/inc
S5	150	recognition time for short pause (EOD-free and EOD-busy) 20 - 250ms	out
S6	50	supervision time for glare seizure 20-255ms	out
S7	0	guard time before new outgoing seizure	out/inc
		0: 500ms
		1 - 255: guard time in 1 s.-steps
S8	5	reanswer supervision time on outgoing traffic	out
		0: immediate forward release to the line after clear back
		1 - 254: delayed forward release to the line after clear back in 1 s.-steps
		255: endless ( no forward release to the line after clear back, waiting for release from DH)
S9	0	answer supervision time on outgoing directed traffic	out
		0: no answer supervision
		1 - 255: answer supervision in 10 s.-steps
S10	40	supervision time for release forward after clear back on incoming traffic	inc
		0: endless forward release supervision
		1 - 255: alarm to DH after supervision time in 1 s.-steps
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve


Parameter	Default	Description				Remark
P1-high*	0	2 / 4 wire voice				only 4 wire voice implemented
		0	4 wire voice
		1	2 wire voice (Hybrid)
P1-low*	0	E&M - type
		0	type IA (V)
		1	DC5
		2	type I
		3	type II
		4	HL / LL with type I			not used
		5	HL / LL with type IA (V)			not used
P2	0	Impedance-Index
			level A->D [dB]	level D->A [dB]	A / μ-law
		0	-3,5	-3,5	A	4 wire standard level C13
		1	-1,5	-1,5	A	Australia old
		2	+0,5	-4,5	A	GBR
		3	0	-6	m	USA
		4	-4,5	-2,5	A	GUS
		5	-2,5	-4,5	A	BRD
		6	0	0	A	Australia new
		7	-7,0	0	A	standard level for 4-2 wire-converter with (-3,5/-3,5)
		8	0	-8,5	A	ITL railway + EVU
		9	+7	-16,0	A	Korea, Japan
		10	+4,3	-13,0	A	BRD, GUS, UNG C11-FDM
		11	+3,3	-12,0	A	GUS C11
P3-high*	0	Low level supervision control				not used
		0	only line supervision
		1	line supervision with periodic recovery
		2	alarm processing
P3-low*	0	Normal / Inverse mode
		0	Normal Signalling (Idle: M=OFF / E=OFF)
		1	Inverse Signalling for M- and E-wire (Idle: M=ON / E=ON)
		2	Inverse Signalling only for E-wire (Idle: M=OFF / E=ON)
		3	Inverse Signalling only for M-wire (Idle: M=ON / E=OFF)
P4	0	reserve
P5-high*	0	Quad-SICOFI Version				Parameter depends on QUAD-SICOFI-Version
		0	Version different from V2.3 (on only in talk state)
		1	Version V2.3 (always on)
P5-low*	4	Last Look (LL)
		0-15	(... x 1ms)
P6-high*	0	reserve
P6-low*	0	reserve
P7-high*	0	dial tone recognition				out
		0	no dial tone recognition
		1	with dial tone recognition
P7-low*	0	signalling direction				out/inc
		0	Bothway directed (glare seizure: priority of incoming seizure)
		1	outgoing directed
		2	incoming directed
		3	bothway directed (glare seizure: release of line)
P8-high*	0	start dial line signal				out/inc
		0	no start dial line signal
		1	with start dial line signal
P8-low*	0	dialing method				out/inc
		0	DP-dial
		1	MFC-R2, SOCOTEL, DTMF
P9-high*	0	restore procedure, if bothway or outgoing directed traffic				out
		0	no restore procedure
		1	with restore procedure (put in service)
		2	with restore procedure (line alarm)
		3	with restore procedure (in service and line alarm)
P9-low*	0	forward release after EOD-busy (Valid only when P10-Low=1)				out
		0	without forward release
		1	with forward release
P10-high*	0	blocking as line signal, if bothway or incoming directed traffic				inc
		0	without blocking as line signal
		1	with blocking as line signal
P10-low*	0	end-of-dial line signal				out/inc
		0	no end-of-dial line signal
		1	with eod-of-dial line signal (EOD-free and EOD-busy)
P11	0	reserve
P12	0	reserve
P13	0	reserve
P14	0	reserve

* High und low byte values are hexadecimal, which have to be converted into decimal to get the corresponding parameter value.

Example: Parameter P3: high byte: 2, low byte: 0 ==> P3[Hex]=20 --> P3[Dec]=32

(106): DB_AM_DEV_OB2: OB2


Longtimer	Default	Description	Remark
L1	300ms	min. recognition time for signal change (10ms - 5s)
L2	1s	sending time for seizure (0.4 - 3s)
L3	1s	sending time for release and release acknowledge (0.4 - 3s)
L4	1s	ignore of incoming signal or delayed sending of line signals after previous sended line signals or received line signals (0.4 - 3s)
L5	10s	outgoing guarde time (5 - 30s)
L6	10s	supervision time for release acknowledge (5 - 30s)
L7	10s	max. time for valid signal, min. recognition time for blocking if P9-low=1


Shorttimer	Default	Description		Remark
S1	0	reserve
S2	0	reserve
S3	0	listener / control channel
S3	0	0 1	listener channel control channel
S4	0	reserve
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	answer supervision time
		0	no supervision
		1-255	with supervision in 30 s.-steps
S14	0	conversation supervision time
		0	no supervision
		1 - 255	with supervision in 30 s.-steps


Parameter	Default	Description				Remark
P1-high*	0	2 / 4 wire voice				only 4 wire voice implemented
		0	4 wirevoice
		1	2 wire voice (fork)
P1-low*	0	E&M - type
		0	type IA (V)
		1	DC5
		2	type I
		3	type II
		4	HL / LL with type I			not used
		5	HL / LL with type IA (V)			not used
P2	0	Impedance-Index
			level A->D [dB]	level D->A [dB]	A / μ-law
		0	-3,5	-3,5	A	4 wire standard level C13
		1	-1,5	-1,5	A	Australia old
		2	+0,5	-4,5	A	GBR
		3	0	-6	m	USA
		4	-4,5	-2,5	A	GUS
		5	-2,5	-4,5	A	BRD
		6	0	0	A	Australia new
		7	-7,0	0	A	standard level for 4-2 wire-converter with (-3,5/-3,5)
		8	0	-8,5	A	ITL railway + EVU
		9	+7	-16,0	A	Korea, Japan
		10	+4,3	-13,0	A	BRD, GUS, UNG C11-FDM
		11	+3,3	-12,0	A	GUS C11
P3-high*	0	low level-controling				not used
		0	only line supervision
		1	line supervision with going in service periodical
		2	with alarm measuring
P3-low*	0	Normal / Inversmode				only valid for high level-line
		0	Normal Signaling (Idle: M=OFF / E=OFF)
		1	Inverse Signaling at M- and E-wire (Idle: M=ON / E=ON)
		2	Inverse Signaling only at E-wire (Idle: M=OFF / E=ON)
		3	Inverse Signaling only at M-wire (Idle: M=ON / E=OFF)
P4		reserve
P5-high*	0	Quad-SICOFI Version				Parameter depends from version of QUAD-SICOFI
		0	Version not equal V2.3 (switched on only at talk-state)
		1	Version V2.3 (switched on always)
P5-low*	4	Last Look (LL)
		0-15	multiple of 1ms
P6-high*	0	send of release acknowledge
		0	no release acknowledge
		1	with release acknowledge ( P6-low=1)
P6-low*	0	send receive of release signal
		0	no release signal
		1	with release signal
P7-high*	0	rering after answer (P6-low=0)
		0	release and incoming seizure
		1	ignore
P7-low*	0	rering befor answer
		0	release and incoming seizure
		1	ignore
P8-high*	0	outgoing guard time at line without release signal (P6-low=0)
		0	without guard time
		1	with guard time (L5)
P8-low*	0	seizure with/without line signal
		0	seizure with line signal
		1	outgoing seizure without line signal
		2	automatic incoming seizure without line signal
P9-high*	0	change of level attenuation signal
		0	without change level
		1	with change level
P9-low*	0	blocking signaling
		0	no block signal
		1	with block signal
P10	0	reserve
P11	0	reserve
P12	0	reserve
P13	0	reserve
P14	0	reserve

* High und low byte values are hexadecimal, which have to be converted into decimal to get the corresponding parameter value.

Example: Parameter P3: high byte: 2, low byte: 0 ==> P3[Hex]=20 --> P3[Dec]=32

(107): DB_AM_DEV_TFUNG2: TSEMHUN2


Longtimer	Default (ms)	Description	Remark
L1	600	transmission time of long pulses (outgoing/incoming)	out/inc
		(10 - 30000 ms)
L2	300	min.recognition time of long pulses (outgoing/incoming)	out/inc
		(10 - 30000 ms)
L3	1700	min.recognition time of blocking (outgoing/incoming)	out/inc
		(10 - 30000 ms)
L4	240	min. pause between 2 sending signals (outgoing/incoming)	out/inc
		(10 - 30000 ms)
L5	300	supervision of glare seizure (outgoing)	out
		(10 - 30000 ms)
L6	400	supervision of glare release (outgoing)	out
		(10 - 30000 ms)
L7	0	reserve


Shorttimer	Default	Description		Remark
S1	150	transmission time of short pulses (outgoing/incoming)		out/inc
		1 - 255 ms
S2	100	min. recognition time of short pulses (outgoing/incoming) max. recognition time of dial pulses and dial pauses (S=10) (incoming)		out/inc
		1 - 255 ms
S3	4	min. recognition time of dial pulses (incoming)		inc
		1 - 255 ms
S4	200	min. recognition time of interdigit time (S2+S4) (incoming)		inc
		1 - 255 ms
S5	9	supervision of release guard after clear forward (outgoing)		out
		0	no supervision
		1 - 255	multiples of 10 s
S6	10	delay ofclear forward after clear back (outgoing)
		0	send clear forward promptly
		1 - 255	multiples of 10 s
S7	0	outgoing guard time (outgoing/incoming)		out/inc
		0	6 s
		1 - 255	multiples of 250 ms
S8	0	supervision of clear forward after clear back (incoming)		inc
		0	90 s; after T/O blocking to DH, wait for release
		1 - 255	multiples of 10 s; after T/O idle after outgoing guard time
S9	9	supervision of answer (outgoing)		g
		0	no supervision
		1 - 255	multiples of 10 s
S10	0	Reserve
S11	0	Reserve
S12	0	Reserve
S13	0	Reserve
S14	0	Reserve


Parameter	Default	Description				Remark
P1-high*	0	2 / 4 wire voice
		0	4 wire voice
		1	2 wire voice (fork)
P1-low*	0	E&M - type
		0	type IA (V)
		1	DC5
		2	type I
		3	type II
		4	HL / LL with type I			not used
		5	HL / LL with type IA (V)			not used
P2	0	Impedance-Index
			level A->D [dB]	level D->A [dB]	A / μ-law
		0	-3,5	-3,5	A	4 wire standard level C13
		1	-1,5	-1,5	A	Australia old
		2	+0,5	-4,5	A	GBR
		3	0	-6	m	USA
		4	-4,5	-2,5	A	GUS
		5	-2,5	-4,5	A	BRD
		6	0	0	A	Australia new
		7	-7,0	0	A	standard level for 4-2 wire-converter with (-3,5/-3,5)
		8	0	-8,5	A	ITL railway + EVU
		9	+7	-16,0	A	Korea, Japan
		10	+4,3	-13,0	A	BRD, GUS, UNG C11-FDM
		11	+3,3	-12,0	A	GUS C11
P3-high*	0	low level-controling				not used
		0	only line supervision
		1	line supervision with going in service periodical
		2	with alarm measuring
P3-low*	0	Normal / Inversmode				only valid for high level-line
		0	Normal Signaling (Idle: M=OFF / E=OFF)
		1	Inverse Signaling at M- and E-wire (Idle: M=ON / E=ON)
		2	Inverse Signaling only at E-wirer (Idle: M=OFF / E=ON)
		3	Inverse Signaling only at M-wire (Idle: M=ON / E=OFF)
P4		reserve
P5-high*	0	Quad-SICOFI Version				Parameter depends from version of QUAD-SICOFI
		0	Version not equal V2.3 (switched on only at talk-state)
		1	Version V2.3 (switched on always)
P5-low*	4	Last Look (LL)
		0-15	multiple of 1ms
P6-high*	0	reserve
P6-low*	0	transmission of seizure acknowledge (incoming)				inc
		0	no transmission
		1	transmission
P7-high*	0	supervision of dial tone (outgoing)				out
		0	no supervision
		1	supervision
P7-low*	0	direction of seizure				out/inc
		0	bidirectional
		1	outgoing
		2	incoming
P8	0	supervision of seizure acknowledge (outgoing)				out
		0	no supervision
		1-255	supervision
P9	0	test procedure (seizure acknowledge or release guard fails to come) (outgoing)				out
		0	no test procedure
		1-255	multiples of 10 s; time between testcycles
P10-high*	0	out of service (incoming/bothway)				inc
		0	no line signal
		1	continuous line signal
P10-low*	0	startup (outgoing/bothway)				out
		0	idle
		1	seizure with release
P11-high*	2	type of dialing (outgoing/incoming)				out/inc
		0	IWV
		1	DTMF
		2	MFC-R2
P11-low*	0	recognition of dial pulse during interdigit time (incoming)				inc
		0	digit is invalid (0F)			TF-signaling for Hungary
		1	digit is valid			TF-signaling for Brasil FURNAS
P12-high*	0	operator signals (override, rering) (outgoing)				out
		0	line with no operator signals
		1	line with operator signals
P12-low*	0	override (incoming)				inc
		0	ignore override from line (no automatic override)
		1	attendant intercept
		2	ignore override (automatic override)
		3	manual override (calling party RLC)
		4	manual override, no sending of answer and clear back when B on-hook (first party RLC)
P13-high*	0	rering (incoming)				inc
		0	line with no rering
		1	line with rering
P13-low*	0	activation of calling party RLC with manual override (outgoing)				out
		0	no
		1	activation
P14	0	reserve

* High und low byte values are hexadecimal, which have to be converted into decimal to get the corresponding parameter value.

Example: Parameter P3: high byte: 2, low byte: 0 ==> P3[Hex]=20 --> P3[Dec]=32

(108): DB_AM_DEV_GUSNORK2: CISNORK2


Longtimer	Default (ms)	Description	Remark
L1	0	reserve
L2	0	reserve
L3	0	reserve
L4	0	reserve
L5	0	reserve
L6	0	reserve
L7	0	reserve


Shorttimer	Default (ms)	Description	Remark
S1	0	reserve
S2	0	reserve
S3	0	reserve
S4	0	reserve
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve


Parameter	Default	Description	Remark
P1	0	reserve
P2	0	reserve
P3	0	reserve
P4	0	reserve
P5	0	reserve
P6	0	reserve
P7	0	reserve
P8	0	reserve
P9	0	reserve
P10	0	reserve
P11	0	reserve
P12	0	reserve
P13	0	reserve
P14	0	reserve

(109): DB_AM_DEV_GUSIND2: CISIND2


Longtimer	Default (ms)	Description	Remark
L1	2800	recognition of answer (P10-low=3) with ANI-2800 ms without ANI-70 ms (100-30000ms)	out: local
L2	500	minimum distance between 2 sending signals (100-1000ms)	out/in: toll/local
L3	0	reserve
L4	2000	recognition time for blocking/line alarm (1000-5000ms)	out/in: toll/local
L5	500	outgoing guard time (100-5000ms)	out/in: toll/local
L6	1000	delayed speechpaththrough connection (1000-3000ms)	out/in: toll/local if P10-low=0
L7	3000	delayed message ANI-removal to DH (1000-30000ms)	out: local P10-low=1 or 2


Shorttimer	Default (ms)	Description	Remark
S1	40	max. recognition time for short pulses (S-pulses) min. recognition time for long pulses (L-pulses) (28-60ms)	out/in: toll/local
S2	130	max. recognition time for long pulses (S-pulses) min. recognition time for release pulses (R-pulses) (100-150ms)	out/in: toll/local
S3	90	max. recognition time for dial pulses (make and break) (60-100ms)	in: toll/local
S4	0	reserve
S5	40	time for glare seizure (40-150ms)	out: toll/local
S6	20	answer supervision time 0: no supervision 1-120: supervision in 30 s.-steps	out: toll/local
S7	3	simulation of end-of-dial-free 0: no simulation 1-120: simulation after time in 10 s.-steps	in: toll
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve


Parameter	Default	Description				Remark
P1-high*	0	2 / 4 wire voice				only 4 wire voice implemented
		0	4 wire voice
		1	2 wire voice (fork)
P1-low*	0	E&M - type
		0	type IA (V)
		1	DC5
		2	type I
		3	type II
		4	HL / LL with type I			not used
		5	HL / LL with type IA (V)			not used
P2	0	Impedance-Index
			level A->D [dB]	level D->A [dB]	A / μ-law
		0	-3,5	-3,5	A	4 wire standard level C13
		1	-1,5	-1,5	A	Australia old
		2	+0,5	-4,5	A	GBR
		3	0	-6	m	USA
		4	-4,5	-2,5	A	GUS
		5	-2,5	-4,5	A	BRD
		6	0	0	A	Australia new
		7	-7,0	0	A	standard level for 4-2 wire-converter with (-3,5/-3,5)
		8	0	-8,5	A	ITL railway + EVU
		9	+7	-16,0	A	Korea, Japan
		10	+4,3	-13,0	A	BRD, GUS, UNG C11-FDM
		11	+3,3	-12,0	A	GUS C11
P3-high*	2	low level-controling				not used
		0	only line supervision
		1	line supervision with going in service periodical
		2	with alarm measuring
P3-low*	0	Normal / Inversmode				only valid for high level line
		0	normal signaling (Idle: M=OFF / E=OFF)
		1	invers signaling at M- and E-wire (Idle: M=ON / E=ON)
		2	invers signaling only at E-wire (Idle: M=OFF / E=ON)
		3	invers signaling only at M-wire (Idle: M=ON / E=OFF)
P4	0	reserve
P5-high*	0	Quad-SICOFI Version				Parameter depends from version of QUAD-SICOFI
		0	Version not equal V2.3 (switched on only at talk-state)
		1	Version V2.3 (switched on always)
P5-low*	4	Last Look (LL)
		0-15	multiple of 1ms
P6-high*	0	reserve
P6-low*	0	put in service procedure				out/in: local/toll
		0	send no line signal
		1	- seizure, release (outgoing, bothway directed P8=0,3,4) - release (inkoming directed P8=1,2)
P7-high*	0	type of partner exchange				out: local/toll
		0	new exchange type (with register)
		1	old exchange type (without register)
P7-low*	0	dial tone supervision				out/in: local
		0	without dial tone supervision
		1	with dial tone supervision
P8	3	seizure direction				out/in: toll/local
		0	outgoing directed (local or toll ascending)
		1	incoming directed (local or toll ascending)
		2	incoming directed (local descending, converting toll descending->local)
		3	bothway directed (combined) (outgoing or incoming local or outgoing toll ascending or incoming toll descending with converting toll descending -> local) Priority of seizure:incoming
		4	bothway directed (combined) (outgoing or incoming local or outgoing toll ascending or incoming toll ascending or outgoing local descending Priority of seizure: outgoing
P9-high*	1	send blocking at incoming or bothway directed line				out/in: local/toll
		0	no blocking transmission
		1	with blocking transmission
P9-low*	1	reaction of message AUSLÖSEN WE_BESETZT from DH before answer				in: local/toll
		0	no reacktion
		1	backward release transmission
P10-high*	0	reaction of rering from line after backward release at incoming descending traffic				in: toll
		0	no reaction
		1	simulated rering (release, seizure, dial)
P10-low*	3	reaction auf ANI-request/removal from line				out: local
		0	ANI-request/removal will be ignored from LW
		1	ANI-START message send to DH after recognition of ANI-removal (after answer)
		2	ANI-START message send to DH after recognition of ANI-request (after answer)
		3	line without ANI line signal means answer after L1=70 ms
P11	0	reserve
P12	0	reserve
P13	0	reserve
P14	0	reserve

* High und low byte values are hexadecimal, which have to be converted into decimal to get the corresponding parameter value

Example: Parameter P3: high byte: 1, low byte:10 ==> P9[Hex]=11 --> P9[Dec]=17

(110): DB_AM_DEV_GUSCOMB2: CISCOMB2


Longtimer	Default (ms)	Description	Remark
L1	0	reserve
L2	0	reserve
L3	0	reserve
L4	0	reserve
L5	0	reserve
L6	0	reserve
L7	0	reserve


Shorttimer	Default (ms)	Description	Remark
S1	0	reserve
S2	0	reserve
S3	0	reserve
S4	0	reserve
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve


Parameter	Default	Description	Remark
P1	0	reserve
P2	0	reserve
P3	0	reserve
P4	0	reserve
P5	0	reserve
P6	0	reserve
P7	0	reserve
P8	0	reserve
P9	0	reserve
P10	0	reserve
P11	0	reserve
P12	0	reserve
P13	0	reserve
P14	0	reserve

(111): DB_AM_DEV_TMCOT8: TMCOT8


Longtimer	Default (ms)	Description	Remark
L1	600	RNGTM
L2	600	DID
L3	6000	INTRNGTM
L4	150	BWGS
L5	1000	TGTM
L6	0	reserve
L7	60000	PERMTM


Shorttimer	Default (ms)	Description	Remark
S1	200	BUFERTM
S2	0	reserve
S3	0	reserve
S4	0	reserve
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve


Parameter	Default	Description	Remark
P1	1	COTGL1
P2	0	reserve
P3	0	reserve
P4	0	reserve
P5	0	reserve
P6	0	reserve
P7	0	reserve
P8	0	reserve
P9	0	reserve
P10	0	reserve
P11	0	reserve
P12	0	reserve
P13	0	reserve
P14	0	reserve

(112): DB_AM_DEV_TMD24_GSR: TMD24GSR


Longtimer	Default (ms)	Description	Remark
L1	250	HC LT0
L2	600	CODISCTM
L3	10000	INTRNGTM
L4	150	MDISCTM
L5	0	reserve
L6	8000	IPERMTM
L7	60000	PERMTM


Shorttimer	Default (ms)	Description	Remark
S1	200	BUFERTM
S2	0	reserve
S3	0	reserve
S4	0	reserve
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve

(113): DB_AM_DEV_TMDID8: TMDID8


Longtimer	Default (ms)	Description	Remark
L1	300	CODISCTM
L2	0	reserve
L3	0	reserve
L4	0	reserve
L5	0	reserve
L6	0	reserve
L7	0	reserve


Shorttimer	Default (ms)	Description	Remark
S1	0	reserve
S2	220	WINKTM
S3	0	reserve
S4	0	reserve
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve


Parameter	Default	Description	Remark
P1	2	PROT2
P2	1	PROT1
P3	0	reserve
P4	0	reserve
P5	2	HC P4
P6	0	reserve
P7	0	reserve
P8	0	reserve
P9	0	reserve
P10	0	reserve
P11	0	reserve
P12	0	reserve
P13	0	reserve
P14	0	reserve

(114): DB_AM_DEV_TMD24_DID: TMD24DID


Longtimer	Default (ms)	Description	Remark
L1	200	TDID2
L2	0	reserve
L3	0	reserve
L4	0	reserve
L5	0	reserve
L6	0	reserve
L7	0	reserve


Shorttimer	Default (ms)	Description	Remark
S1	0	reserve
S2	220	TDID1
S3	0	reserve
S4	0	reserve
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve


Parameter	Default	Description	Remark
P1	2	PROT2
P2	1	PROT1
P3	0	reserve
P4	0	HC P3
P5	1	HC P4
P6	0	HC P5
P7	0	reserve
P8	0	reserve
P9	0	reserve
P10	0	reserve
P11	0	reserve
P12	0	reserve
P13	0	reserve
P14	0	reserve

(115): DB_AM_DEV_T1EMW: T1EMW


Longtimer	Default (ms)	Description	Remark
L1	600	Guard time interval (For Satellite Interface, this value must be changed to 1150ms)
L2	0	reserve
L3	0	reserve
L4	0	reserve
L5	0	reserve
L6	0	reserve
L7	0	reserve


Shorttimer	Default (ms)	Description	Remark
S1	0	reserve
S2	0	reserve
S3	0	reserve
S4	0	reserve
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve


Parameter	Default	Description	Remark
P1	0	reserve
P2	0	reserve
P3	0	reserve
P4	0	reserve
P5	0	reserve
P6	0	reserve
P7	0	reserve
P8	0	reserve
P9	0	reserve
P10	0	reserve
P11	0	reserve
P12	0	reserve
P13	0	reserve
P14	0	reserve

(119): DB_AM_DEV_TMANI_HKZ: TMANI HKZ


Longtimer	Default (ms)	Description	Remark
L1	200	flash or ground signal transmission time (60- 500 ms)
L2	10000	periodical ringing supervision for release re cognition from PSTN before answer (incoming traffic) (4000-15000 ms)
L3	100	minimum time for release recognition from PSTN (feeding interruption) (see P01-high and P02-high) (20- 200 ms)
L4	400	delay for speech path through-connection after answer; minimum time for answer; delay for line supervision activation after answer (incoming traffic) (100- 2000 ms)
L5	400	maximum time for charge pulse (300-600 ms)	only if P4_LOW=7 or 8
L6	120	minimum time of ring rcognition (100- 500 ms)
L7	5000	idle supervision time (see P04-high) (500-30000 ms)	In spain used also for charge recognition while guard time after a call


Shorttimer	Default (ms)	Description	Remark
S1	40	minimum time for charge pulse (40- 200 ms)
S2	90	minimum time for charge pause (40- 200 ms)
S3	0	listener-/controlchannel 0 listener-channel 1 control-channel
S4	0	line signaling 0: with HKZ-line signaling 1: without line signaling, without loop 2: without line signaling, with loop
S5	0	dialing with V_ON 0: normal dialing with V_ON 1: dialing with V_OFF for France
S6	0	delayed activation of ring detection 0: without delay 1-10: delay (multiple of 500 ms) standard: 4
S7	0	minimum time for polarity reversal recognition maximal time for reversal charge recognition (multiple of 10 ms) (1- 200)
S8	1	high: answer procedure for collect calls incomming traffic) (0- 2 ) 0: normal answer: loop (Brazil) 1: answer with loop (1 sec.), loop interruption (S8- low), back to answer (loop) (protection against collect calls) 2: if HiPath party authorized: normal answer (loop) if HiPath party unauthorized: answer with loop (1sec.), loop interruption (S8-low), back to answer (loop). (protection against collect calls is only for unauthorized users) low: loop interruptiion time for collect calls (incoming traffic) ( 0- 10) 0 250: ms loop interruption 1 - 10: loop interruption (multiple of 500 ms)
S9	0	reanswer supervision (outgoing traffic) (0- 255) 0: no supervision 1 - 255: reanswer supervision (in seconds) as long as the calling party remains off-hook, the called party has the possibility to hook on and off again. reanswer supervision can be activated only when P2-low = 2
S10	2	guard time after an outgoing call (in seconds) (1- 30)
S11	2	guard time after an incoming call (in seconds) (1- 30)
S12	0	conversation time limit (0- 255)
S13	0	conversation time limit (0- 255) 0: no limit 1 - 255: conversation time (multiple of 30 sec.) after the timer expired the conversation will be automatically disconnected.
S14	0	charge characteristic ( 12kHz / 16 kHz ) Belgium, Bulgaria, Poland, South Africa ( 16 kHz Standard ) S14 36 P12 36 Greece, Luxemburg, Norway ( 16 kHz ) S14 36 P12 70 France, Portugal ( 12 kHz Standard ) S14 50 P12 55 Hungary, Irland ( 12 kHz ) S14 30 P12 27 Italy ( 12 kHz ) S14 30 P12 53 Australia ( 12 kHz ) S14 50 P12 50 Spain ( 12 kHz ) S14 40 P12 55 Austria ( 12 kHz ) S14 30 P12 31


	Description		Description
P1 High	Feeding interruption PSTN (incoming call)	P1 Low	Polarity Reversal From PSTN (incoming call)
P2 High	Feeding interuption PSTN (outgoing call)	P2 Low	Polarity Reversal From PSTN (outgoing call)
P3 High	Answer loop (incoming call)	P3 Low	Release recognition for feeding interruption of PSTN
P4 High	Loop start supervision and earth calling	P4 Low	charge or answer pulse (outgoing traffic)
P5 High	Line Interface parameters (OHS, SQ)	P5 Low	Line Interface parameters ( DCV, MINI)
P6 High	Line Interface parameters (FOH / ILIM / FIR)	P6 Low	Dial Tone Supervision (outgoing call)
P7	Answer Supervision
P8 High	Supervision of PSTN Release	P8 Low	Noise Supervision (x 4ms)
P9 High	Charge Simulation	P9 Low	Charge Level
P10	Busy Tone Configuration
P11	Ring Frequency Range
P12 High	Reserved	P12 Low	Dialing method
P13 High	Voltage Threshold	P13 Low	Current Threshold
P14	Attenuation TX/RX


	Default Value		Default Value		Default Value
P1	16	P1 High	1	P1 Low	0
P2	18	P2 High	1	P2 Low	2
P3	0	P3 High	0	P3 Low	0
P4	0	P4 High	0	P4 Low	0
P5	140	P5 High	8	P5 Low	12
P6	97	P6 High	6	P6 Low	1
P7	0	P7	0
P8	2	P8 High	0	P8 Low	2
P9	0	P9 High	0	P9 Low	0
P10	0	P10	0
P11	0	P11	0
P12	0	P12 High	0	P12 Low	0
P13	0	P13 High	0	P13 Low	0
P14	0	P14	0

(120): DB_AM_DEV_TMANI_DID_ITL: TMANI DID ITL


Longtimer	Default (ms)	Description	Remark
L1	600	minimum time between end of dial and answer (100-1000 ms)
L2	600	minimum time between answer and backward release (100-1000 ms)
L3	0	reserve
L4	200	delay time for speech path through-connection after rering and reanswer (100-1000 ms)
L5	0	reserve
L6	0	reserve
L7	00	reserve


Shorttimer	Defaul (ms)	Description	Remark
S1	50	minimum time for incoming seizure (20-250 ms)
S2	24	minimum length of dial pulse (8-32 ms)
S3	96	maximum length of dial pulse (32-120 ms)
S4	16	minimum length of dial pause (8-32 ms)
S5	114	digit complete (32-200 ms)
S6	120	release recognition from CO after dialing (40-250 ms)
S7	200	minimum time for ring (on/off) recognition (40-255 ms)
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve


	Description		Description
P1	Dialing method
P2	End of dial control
P3	TSL Refresh
P4 High	Reserved	P4 Low	Reserved
P5 High	Line Interface parameters (OHS, SQ)	P5 Low	Line Interface parameters (DCV, MINI)
P6 High	Line Interface parameters (FOH / ILIM / FIR)	P6 Low	Reserved
P7	Busy Tone Configuration
P8	Normal feeding supervision
P9	The way of speech path through connection
P10 High	Charge Level	P10 Low	Noise supression
P11	Ring Frequency Range
P12 High	Reserved	P12 Low	Reserved
P13 High	Voltage Threshold	P13 Low	Current Threshold
P14	Attenuation TX/RX


	Default Values		Default Values		Description
P1	0	P1	0
P2	0	P2	0
P3	0	P3	0
P4	0	P4 High	0	P4 Low	0
P5	12	P5 High	0	P5 Low	12
P6	64	P6 High	4	P6 Low	0
P7	10	P7	10
P8	30	P8	30
P9	0	P9	0
P10	2	P10 High	0	P10 Low	2
P11	2	P11	2
P12	0	P12 High	0	P12 Low	0
P13	0	P13 High	0	P13 Low	0
P14	0	P14	0

(121): DB_AM_DEV_TMANI_DID_BEL: TMANI DID BEL


Longtimer	Default (ms)	Description	Remark
L1	0	reserve
L2	600	minimum time between answer and backward release (100-1000 ms)
L3	0	reserve
L4	0	reserve
L5	0	reserve
L6	0	reserve
L7	0	reserve


Shorttimer	Default (ms)	Description	Remark
S1	50	minimum time for incoming seizure (20-250 ms)
S2	24	minimum length of dial pulse (8-32 ms)
S3	96	maximum length of dial pulse (32-120 ms)
S4	16	minimum length of dial pause (8-32 ms)
S5	114	digit complete (32-200 ms)
S6	120	release recognition from PSTN after dialing (40-250 ms)
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve


	Description		Description
P1	Dialing method
P2 High	Reserved	P2 Low	Reserved
P3 High	Reserved	P3 Low	Reserved
P4 High	Reserved	P4 Low	Reserved
P5 High	Line Interface parameters (OHS, SQ)	P5 Low	Line Interface parameters ( DCV, MINI)
P6 High	Line Interface parameters (FOH / ILIM / FIR)	P6 Low	Reserved
P7	Busy Tone Configuration
P8	Normal feeding supervision
P9	The way of speech path through connection
P10 High	Charge Level	P10 Low	Noise supression
P11	Ring Frequency Range
P12 High	Reserved	P12 Low	Reserved
P13 High	Voltage Threshold	P13 Low	Current Threshold
P14	Attenuation TX/RX


	Default Values		Default Values		Description
P1	1	P1	1
P2	0	P2	0
P3	0	P3	0
P4	0	P4 High	0	P4 Low	0
P5	12	P5 High	0	P5 Low	12
P6	64	P6 High	4	P6 Low	0
P7	10	P7	10
P8	30	P8	30
P9	0	P9	0
P10	12	P10 High	12	P10 Low	9
P11	5	P11	5
P12	0	P12 High	0	P12 Low	0
P13	0	P13 High	0	P13 Low	0
P14	0	P14	0

(122): DB_AM_DEV_TMANI_GS_USA: TMANI DID GS LS USA


Longtimer	Default (ms)	Description	Remark
L1	600	RNGTM
L2	600	DID
L3	6000	INTRNGTM
L4	150	BWGS
L5	1000	TGTM
L6	0	reserve
L7	60000	PERMTM


Shorttimer	Default (ms)	Description	Remark
S1	200	BUFERTM
S2	0	reserve
S3	0	reserve
S4	0	reserve
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve


	Description		Description
P1	Loop supervision flag
P2 High	Reserved	P2 Low	Reserved
P3 High	Reserved	P3 Low	Reserved
P4 High	Reserved	P4 Low	Reserved
P5 High	Line Interface parameters (OHS, SQ)	P5 Low	Line Interface parameters ( DCV, MINI)
P6 High	Line Interface parameters (FOH / ILIM / FIR)	P6 Low	Dial Tone Supervision (outgoing call)
P7 High	Reserved	P7 Low	Reserved
P8 High	Reserved	P8 Low	Noise Supervision (x 4ms)
P9 High	Reserved	P9 Low	Reserved
P10	Busy Tone Configuration
P11	Ring Frequency Range
P12 High	Reserved	P12 Low	Dialing method
P13 High	Voltage Threshold	P13 Low	Current Threshold
P14	Attenuation TX/RX


	Default Values		Default Values		Default Values
P1	1	P1	1
P2	0	P2 High	0	P2 Low	0
P3	0	P3 High	0	P3 Low	0
P4	0	P4 High	0	P4 Low	0
P5	12	P5 High	0	P5 Low	12
P6	64	P6 High	4	P6 Low	0
P7	0	P7 High	0	P7 Low	0
P8	2	P8 High	0	P8 Low	2
P9	0	P9 High	0	P9 Low	0
P10	15	P10	15
P11	7	P11	7
P12	0	P12 High	0	P12 Low	0
P13	0	P13 High	0	P13 Low	0
P14	0	P14	0

(122): DB_AM_DEV_TMANI_GS_USA: TMANI DID GS LS USA


Longtimer	Default (ms)	Description	Remark
L1	600	Ring Pulse Recognition Time
L2	600	CO Disconnection Time
L3	6000	Maximum Time between CO Ringing Pulses
L4	150	PBX Disconnection Time
L5	1000	CO Tip Ground Signal Time
L6	0	reserve
L7	60000	CO Maximum Disconnection Start Time after PBX Disconnected First


Shorttimer	Default (ms)	Description	Remark
S1	200	PBX Pause toÿDisconnection after CO Disconnected First
S2	0	reserve
S3	0	reserve
S4	0	reserve
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve


	Description		Description
P1	Loop supervision flag
P2 High	Reserved	P2 Low	Reserved
P3 High	Reserved	P3 Low	Reserved
P4 High	Reserved	P4 Low	Reserved
P5 High	Line Interface parameters (OHS, SQ)	P5 Low	Line Interface parameters ( DCV, MINI)
P6 High	Line Interface parameters (FOH / ILIM / FIR)	P6 Low	Dial Tone Supervision (outgoing call)
P7 High	Reserved	P7 Low	Reserved
P8 High	Reserved	P8 Low	Noise Supervision (x 4ms)
P9 High	Reserved	P9 Low	Reserved
P10	Busy Tone Configuration
P11	Ring Frequency Range (Index)
P12 High	Reserved	P12 Low	Dialing method
P13 High	Voltage Threshold	P13 Low	Current Threshold
P14	Attenuation TX/RX


	Default Values		Default Values		Default Values
P1	1	P1	1
P2	0	P2 High	0	P2 Low	0
P3	0	P3 High	0	P3 Low	0
P4	0	P4 High	0	P4 Low	0
P5	12	P5 High	0	P5 Low	12
P6	64	P6 High	4	P6 Low	0
P7	0	P7 High	0	P7 Low	0
P8	2	P8 High	0	P8 Low	2
P9	0	P9 High	0	P9 Low	0
P10	15	P10	15
P11	7	P11	7
P12	0	P12 High	0	P12 Low	0
P13	0	P13 High	0	P13 Low	0
P14	0	P14	0

(123): DB_AM_DEV_DIUCAPUL: Signalisation R2 for BWI ( Bundeswehr )


Longtimer	Default (ms)	Description	Remark
L1	5000	release acknowledgement supervision after forward release (2000-20000 ms)
L2	1000	pause between answer and backward release (collect call) ( only for P11=1 or 2) (1000-10000 ms)
L3	2000	pause between backward release and answer (collect call (only for P11=1 or 2) (1000-10000 ms)
L4	0	reserve
L5	600	send time for long pulses (480-720 ms)
L6	450	pause time before sending seizure acknowledge (100-500 ms)
L7	300	max. receive time for short pulses (200-400 ms)


Shorttimer	Default (ms)	Description	Remark
S1	150	send time for short pulses (120-180ms)
S2	80	min. receive time for short pulses (60-100ms)
S3	0	reserve
S4	0	reserve
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve


Parameter	Default	Description		Remark
P1	2	dialing method
		0	digit dialing
		1	MFV dialing
		2	MFC dialing
P2	0	reserve
P3	0	seizure routing
		0	bothway
		1	outgoing
		2	incoming
P4	0	reserve
P5	24	reseizure lookout time outgoing
		1-255	multiple of 250 ms
P6	0	outgoing dial tone supervision
		0	no supervision
		1	supervision
P7	90	answer supervision on outgoing calls
		0	no supervision
		1-255	supervision
P8	0	reserve
P9	0	reserve for override a call – new feature *)
P10	0	reserve
P11	1	answer procedure for collect call
		0	normal answer signal to CO
		1	answer/clear back/answer to CO
		2	answer to CO if ready for collect call
P12	0	reserve
P13	0	reserve
P14	0	reserve

${DocTitle}, ID: ${DocID}

© 02/2025 Mitel Networks Corporation. - All rights reserved.
Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG.
All other trademarks herein are the property of their respective owners.