158.3.1 START-REGEN

Start the regenerating run for creation of MML command file.


Command Code	Parameter
START-REGEN	USERCODE=<string>,[SYSNO=<string>]
	,CONT=Y;

	\|,CONT=N,[STANDBY=<param>]
	,[SYSTYPE=<param>],[PROT=<param>]
	,[DATYPE=<param>],[ARCHIVE=<param>]
	,{[UNIT1=<param>],[APSVERS1=<number>]
	,[CFIGCUS1=<param>]},{[UNIT2=<param>]
	,[APSVERS2=<number>],[CFIGCUS2=<param>]}
	,{[UNIT3=<param>],[APSVERS3=<number>]
	,[CFIGCUS3=<param>]},{[UNIT4=<param>]
	,[APSVERS4=<number>],[CFIGCUS4=<param>]}
	,{[UNIT5=<param>],[APSVERS5=<number>]
	,[CFIGCUS5=<param>]},{[UNIT6=<param>]
	,[APSVERS6=<number>],[CFIGCUS6=<param>]}
	,{[UNIT7=<param>],[APSVERS7=<number>]
	,[CFIGCUS7=<param>]},{[UNIT8=<param>]
	,[APSVERS8=<number>],[CFIGCUS8=<param>]}
	,{[UNIT9=<param>],[APSVERS9=<number>]
	,[CFIGCUS9=<param>]}
	,[NOUN=<string>],[MMLFILE=<string>]
	,FTRNS=N;

	\|,FTRNS=Y,[FDAT=<param>],BSPTNR=<string>
	,BSLOGID=<string>,BSACCNO=<string>
	,BSPSWD=<string>,[DEL=<param>];

Example

Start a REGEN run

Input:

START-REGEN:"WINDSOR","L31617S0001X00001",,,Y,,,SWU,,,ADS,,,,
,,,,,,,,,,,,,,,,,,,,"CHESE&BUEND";

Output:

Result file: :PAS:L31617/S0001X00001/RE/ADS

A001
C001 *P30252B2001B60101P30252B2000B60101P30252B2000S60101
M2 1 ADD-ANSU:SYSNO,EMPTZDBCCD01,ZDBCCD01;
M2 1 ADD-ANSU:SYSNO,EMPTZDBCCD02,ZDBCCD02;
M2 1 ADD-ANSU:SYSNO,EMPTZDBCCD03,ZDBCCD03;
M2 1 ADD-UCSU:LTU,1,1;
M2 1 ADD-UCSU:LTU,1,2;
M2 1 ADD-DIMSU:ADMCC,1000;
M2 1 ADD-DIMSU:CC,2000,600,40,500,500,275,385,257,268,110,110,0;
M2 1 ADD-DIMSU:ADMLTG,1,100;
M2 1 ADD-DIMSU:LTG,1,800,300,120,600;
M2 1 ADD-BCSU:PER,1,1,1,"Q2057-X ";
M2 1 ADD-BCSU:RG,1,1,7,"Q2058-X ",UN50H65V;
M2 1 ADD-BCSU:PER,1,1,13,"Q2057-X ";
M2 1 ADD-BCSU:PER,1,1,25,"Q2052-X ";
.
.
.

Output:

Result file: :PAS:L31617/S0001X00001/RA/ADS

***DAGEN - DEVELOPMENT AID FOR GENERATION ***********************************
* *
* SSSSSSSSSSSSSSSSSSSSSSS *
* SSS *
* SSS *
* TTTTTTTTTTTTTTTTTTTTTTT SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS *
* TTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTT *
* BBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBBB *
* BBBBBBBBBBBBBBBBBBBBBBB DDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDD *
* DDD *
* DDD *
* DDDDDDDDDDDDDDDDDDDDDDD *
* *
** SWU *** START ************************************************************
* *
* REGEN-RESULT-PROTOCOL DATE : 28.09.87 *
* START : 09:51:18 *
* GENERATED HARDWARE MODULE (SERVER): ADS *
* *
* NAME OF MMLFILE : *
* SYSTEM PROGRAM NUMBER (APS-SPNO.) : P30252B2001A60101 *
* *
* CALLUP UNIT : ADS FTRNS : N *
* PARAMETERS CFIGDA : Y BSPTNR : *
* CUSTDA : Y BSLOGID : *
* PROT : Y BSACCNO : *
* DEL : BSPSWD : (SECRET) *
* *
* ARCHIVE: N *
* *
*********************************** DAGEN - DEVELOPMENT AID FOR GENERATION **
S REGEN-ANUM:A1;H500: AMO ANUM STARTED
EH ADD-ANUM:SYSNO,A1,"L31617S0001X00001";
ME AMO-ANUM -111 ENTER SYSTEM NUMBER INTO DATA BASE
+ REGENERATE COMPLETED;
S REGEN-BCSM:A1;H500: AMO BCSM STARTED
+ ADD-BCSM:A1,GR,SW,1,TTYBSC;
+ ADD-BCSM:A1,GR,SW,13,TTYBSC;
+ ADD-BCSM:A1,GR,HW,N,38,Q2090-X ,,,,,, ,,;
+ ADD-BCSM:A1,GR,HW,N,1,Q2011-X 1,,,,,, ,,;
ME AMO-BCSM -111 BOARD CONFIGURATION, SERVICE MODULES
+ REGENERATE COMPLETED;
S REGEN-LCSM:A1;H500: AMO LCSM STARTED
EH ADD-LCSM:A1,V24,2,V27_,DTE,LOW,EXT,60,VDX;
ME AMO-LCSM -111 LINE CONFIGURATION, SERVICE MODULE
+ REGENERATE COMPLETED;
.
.

Example of ’continuation after interrupt’:

Input:

START-REGEN:"WINDSOR","L31617S0001X00001",Y;

Note

Since the REGEN task has no way of knowing whether the REGEN results of an interrupted AMO were successfully stored in the RE result file before the interrupt occurred, the interrupted AMO is restarted. In some cases, the REGEN run is continued with the AMO called prior to the interrupted AMO, so that the REGEN result file may contain the same command sequence twice over after an interrupt. Superfluous command sequences must be manually deleted from the RE file if errors occur during loading (i.e. during a GENDB run).

${DocTitle}, ID: ${DocID}

© 02/2025 Mitel Networks Corporation. - All rights reserved.
Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG.
All other trademarks herein are the property of their respective owners.