166.2.1 ADD-SBCSU

The action ADD-SBCSU is used to assign station terminals. One assignment order is required for each station number. The first station number is called the main station number. It is used as a reference, if further station numbers (secondary or MSN station numbers) of a bus, OPTISET or S0/S2 point-to-point connection will be assigned. The following alternatives are possible:
•
Assigning a functional bus connection (OPT=FBUS).
•
Assigning the main station number of a CorNet-TS-OPTISET configuration (OPT=OPTI).
•
Setting up the main station number for the components (base station, mobile user, extension connection) of a CorNet-TS-CMI configuration (OPT=CMI).
•
Expanding an OPTISET configuration by a secondary station number (OPT=OPTIEXP).
A maximum of two secondary station numbers can be set up per OPTISET configuration.
•
Assigning a MSN station number for a FBUS/OPTISET configuration (OPT=MSN).
•
Expanding an OPTISET configuration with an MSN secondary station number (OPT=MSN).
•
Expanding station capabilities by adding a service which is not currently assigned to the station number (bus connections and OPTISET configuration) (OPT=SVC).
MSN station numbers or MSN secondary station numbers already assigned to the bus will be automatically extended to the new service(s).
•
Setting up the main station number for an S0/S2 point-to-point connection (OPT=FPP).
•
Assigning a MSN station number via an S0/S2 point-to-point connection (OPT=MSN).
A S0/S2 connection may be extended by any number of MSN station numbers.
Each OPTISET configuration can be expanded by further station numbers with OPT=OPTIEXP, providing the usual general conditions for the OPTISET configuration are complied with (maximum three terminals, maximum three station numbers).
The parameter PEN specifies the location or port equipment number (LTG-LTU-SLOT-CCT) at which the station devices are connected with the station number STNO. If this parameter is not specified, then the first free location in the system is taken, which corresponds to the other parameter values specified (OPT, CONN, DVCFIG).
The device configuration, to which a port equipment number or location is to be assigned, is declared with the parameter DVCFIG.
The parameters OPT, STNO, PEN, CONN, and DVCFIG, as well as TSI and if required, are used to define what devices are to be assigned and where they are to be assigned. The remaining parameters are used to describe device attributes.
The parameter INS does not reflect the exact state of a terminal device. For INS=Y the trunk will be released for call processing, but it will not necessarily be active. A deviation of the terminal devices states and the trunk state is not possible. The exact states of terminal devices and trunks can be interrogated via the AMO SDSU. In the actions DISPLAY and REGENERATE of the AMO SBCSU INS=Y will be output for trunk states different from long term deactivation. A trunk assigned with INS=N is in the state long term deactivation.
The parameters are divided into the following groups:
1.
Addressing parameters :
OPT, CONN, PEN, TSI, MAINO.
2.
General parameters (for all device types):
STNO, DVCFIG, COS1, COS2, LCOSV1, LCOSV2, LCOSD1, LCOSD2, DPLN, ITR, SSTNO, COSX, SPDI, SPDC1, SPDC2, INS, RCBKB, RCBKNA, CBKBMAX, ALARMNO, HMUSIC, DTMFCTRD, DTMFBLK.
3.
Parameters for CorNet terminals:
IDCR, REP, STD, SECR, DSSTNA, DSSTNB, DIGNODIS, OPTICA, OPTIDA, OPTICOM, HEADSET, HSKEY, CBKNAMB, TEXTSEL, CALLOG, PMIDX, COMGRP, APICLASS, SECAPPL, DNIDSP, DCFWBUSY, APMOBUSR, APPM.
4.
Parameter for IP terminals:
IPCODEC (for bandwidth calculation SIP and HFA subscribers in RESMAN), IPPASSW (for HFA subscribers only) and the SIP specific parameters IPADDR, PASSWD, USEID, SECZONE, FIXEDIP, AUTHREQ.
5.
Parameters for general analog terminal:
DFSVCANA, FLASH.
6.
Parameters for functional terminals:
SPROT, FPROT, DPROT, PERMACT, SOPTIDX, FOPTIDX, DOPTIDX, BASICSVC.
The optional protocol type parameters must be declared, if a terminal has already been declared for the relevant service with parameter DVCFIG, e.g. DPROT for DTE.
The BASICSVC parameter must be declared, if the NI BRI protocol has been specified for a protocol type parameter, e.g. DPROT=SBNIBRI for DTE.
7.
Parameters for S0/S2/SIP point-to-point connections:
PERMACT, PROT, OPTIDX.
8.
Board-specific parameters
EXTBUS, ASYNCT, PATTERN, VPI, VCI, LWPAR.
If an existing OPTISET configuration is expanded with a secondary station number (OPT=OPTIEXP), then the values specified for the main station number are used as default values, as far as possible.
If a data terminal (DTE) is assigned together with a voice terminal, then the voice terminal is always associated with the data terminal.
NOTE:  An UFIP client must be linked to an actual desktop phone via parameter CLNTDESK and marked as either CLIENT or OSMO depending on the case.
Example:
The client must be linked to an actual desktop phone via parameter CLNTDESK as CLIENT:

ADD-SBCSU:STNO=<UFIP_STN>,OPT=OPTI,CONN=IP2,PEN=<X-Y-Z-T>,DVCFIG=UFIP, CLNTDESK=<DSKTP_PHN_STN>;

or via CLNTSDESK and OSMO:

ADD-SBCSU:STNO=<UFIP_STN>,OPT=OPTI,CONN=IP2,PEN=<X-Y-Z-T>,DVCFIG=UFIP, CLNTDESK=<DSKTP_PHN_STN>,OSMO=YES;

depending on the case.
Procedure Overview
 
Command Code
Parameter
ADD-SBCSU
STNO=<number>
 
|OPT=FBUS
 
,CONN=<param>
 
,[PEN=<g-uu-sss-ccc>],DVCFIG=<param>
 
,COS1=<number>,COS2=<number>
 
,LCOSV1=<number>,LCOSV2=<number>
 
,LCOSD1=<number>,LCOSD2=<number>
 
,[DPLN=<number>],[ITR=<number>],[SSTNO=<param>]
 
,[COSX=<number>],[SPDI=<number>]
 
,[SPDC1=<number>],[SPDC2=<number>]
 
,[SPROT=<param>],[FPROT=<param>]
 
,[DPROT=<param>],[PERMACT=<param>]
 
,[INS=<param>],[ALARMNO=<number>]
 
,[SOPTIDX=<number>]
 
,[FOPTIDX=<number>],[DOPTIDX=<number>]
 
,[BASICSVC=<param>],[EXTBUS=<param>]
 
,[RCBKB=<param>],[RCBKNA=<param>]
 
,[ASYNCT=<number>],[CBKBMAX=<number>]
 
,[HMUSIC=<number>],[DTMFCTRD=<param>]
 
,[PMIDX=<number>];
 
 
 
|OPT=OPTI
 
,CONN=<param>,[PEN=<g-uu-sss-ccc>]
 
,DVCFIG=<param>,[TSI=<number>]
 
,COS1=<number>,COS2=<number>
 
,LCOSV1=<number>,LCOSV2=<number>
 
,LCOSD1=<number>,LCOSD2=<number>
 
,[DPLN=<number>],[ITR=<number>],[SSTNO=<param>]
 
,[COSX=<number>],[SPDI=<number>]
 
,[SPDC1=<number>],[SPDC2=<number>]
 
,[IDCR=<param>],[REP=<number>],[STD=<number>]
 
,[SECR=<param>]
 
,[FPROT=<param>],[DPROT=<param>]
 
,[INS=<param>],[ALARMNO=<number>]
 
,[RCBKB=<param>],[RCBKNA=<param>]
 
,[DSSTNA=<param>],[DSSTNB=<param>]
 
,[DIGNODIS=<param>],[FOPTIDX=<number>]
 
,[DOPTIDX=<number>],[BASICSVC=<param>]
 
,[OPTICA=<number>],[OPTIDA=<number>]
 
,[ASYNCT=<number>],[OPTICOM=<param>]
 
,[CBKBMAX=<number>],[PATTERN=<number>]
 
,[VPI=<number>],[VCI=<number>]
 
,[HEADSET=<param>],[HSKEY=<param>]
 
,[CBKNAMB=<param>],[TEXTSEL=<param>]
 
,[HMUSIC=<number>],[CALLOG=<param>]
 
,[PMIDX=<number>],[COMGRP=<number>]
 
,[APICLASS=<param>],[SECAPPL=<number>]
 
,[DNIDSP=<param>],[DTMFCTRD=<param>]
 
,[DTMFBLK=<param>],[DCFWBUSY=<param>]
 
,[IPPASSW=<string>],[APMOBUSR=<param>]
 
,[IPCODEC=<param>],[APPM=<param>]
 
,[BLF=<param>],[USRID=<string>]
 
,[SECZON=<string>],[CLNTDESK=<string>]
 
,[SUBIPADD=<string>],[OSMO=<param>];
 
 
 
|OPT=OPTIEXP
 
,MAINO=<number>
 
,DVCFIG=<param>,[TSI=<number>]
 
,[COS1=<number>],[COS2=<number>]
 
,[LCOSV1=<number>],[LCOSV2=<number>]
 
,[LCOSD1=<number>],[LCOSD2=<number>]
 
,[DPLN=<number>],[ITR=<number>],[SSTNO=<param>]
 
,[COSX=<number>],[SPDI=<number>]
 
,[SPDC1=<number>],[SPDC2=<number>]
 
,[IDCR=<param>],[REP=<number>],[STD=<number>]
 
,[SECR=<param>]
 
,[SPROT=<param>],[FPROT=<param>],[DPROT=<param>]
 
,[ALARMNO=<number>]
 
,[RCBKB=<param>],[RCBKNA=<param>]
 
,[DSSTNA=<param>],[DSSTNB=<param>]
 
,[DIGNODIS=<param>]
 
,[SOPTIDX=<number>],[FOPTIDX=<number>]
 
,[DOPTIDX=<number>],[BASICSVC=<param>]
 
,[OPTICA=<number>],[OPTIDA=<number>]
 
,[OPTICOM=<param>],[CBKBMAX=<number>]
 
,[HEADSET=<param>],[HSKEY=<param>]
 
,[DFSVCANA=<param>]
 
,[CBKNAMB=<param>],[TEXTSEL=<param>]
 
,[HMUSIC=<number>],[CALLOG=<param>]
 
,[PMIDX=<number>],[COMGRP=<number>]
 
,[APICLASS=<param>],[SECAPPL=<number>]
 
,[DNIDSP=<param>],[DTMFCTRD=<param>]
 
,[DTMFBLK=<param>],[DCFWBUSY=<param>]
 
,[FLASH=<param>],[APMOBUSR=<param>],[APPM=<param>];
 
 
 
|OPT=CMI
 
,[PEN=<g-uu-sss-ccc>],DVCFIG=<param>
 
,COS1=<number>,COS2=<number>
 
,LCOSV1=<number>,LCOSV2=<number>
 
,LCOSD1=<number>,LCOSD2=<number>
 
,[DPLN=<number>],[ITR=<number>],[SSTNO=<param>]
 
,[COSX=<number>],[SPDI=<number>]
 
,[SPDC1=<number>],[SPDC2=<number>]
 
,[REP=<number>],[STD=<number>]
 
,[SPROT=<param>]
 
,[INS=<param>],[ALARMNO=<number>]
 
,[RCBKB=<param>],[RCBKNA=<param>]
 
,[DSSTNA=<param>],[DSSTNB=<param>]
 
,[DIGNODIS=<param>]
 
,[SOPTIDX=<number>]
 
,[ASYNCT=<number>],[HMUSIC=<number>]
 
,[FPROT=<param>],[DPROT=<param>]
 
,[FOPTIDX=<number>],[DOPTIDX=<number>]
 
,[TEXTSEL=<param>],[DNIDSP=<param>]
,[PMIDX=<number>];
 
 
 
|OPT=FPP
 
,CONN=<param>,[PEN=<g-uu-sss-ccc>]
 
,DVCFIG=<param>
 
,COS1=<number>,COS2=<number>
 
,LCOSV1=<number>,LCOSV2=<number>
 
,LCOSD1=<number>,LCOSD2=<number>
 
,[DPLN=<number>],[ITR=<number>],[SSTNO=<param>]
 
,[COSX=<number>],[SPDI=<number>]
 
,[SPDC1=<number>],[SPDC2=<number>]
 
,PROT=<param>,[PERMACT=<param>]
 
,[INS=<param>],[ALARMNO=<number>]
 
,[OPTIDX=<number>],[RCBKB=<param>]
 
,[RCBKNA=<param>],[LWPAR=<param>]
 
,[ASYNCT=<number>],[CBKBMAX=<number>]
 
,[HMUSIC=<number>],[PMIDX=<number>]
 
,[IPCODEC=<param>],[IPADDR=<number>]
 
,[PASSWD=<string>],[USERID=<string>]
 
,[SECZONE=<string>],[FIXEDIP=<param>]
 
,[AUTHREQ=<param>],[SMGSUB=<param>]
 
,[DTMFCTRD=<param>];
 
 
 
|OPT=SVC
 
,DVCFIG=<param>,[TSI=<number>]
 
,[FPROT=<param>],[DPROT=<param>]
 
,[FOPTIDX=<number>],[DOPTIDX=<number>]
 
,[BASICSVC=<param>]
 
,[OPTICA=<number>],[OPTIDA=<number>];
 
 
 
|OPT=MSN
 
,MAINO=<number>,[TSI=<number>]
 
,[COS1=<number>],[COS2=<number>]
 
,[LCOSV1=<number>],[LCOSV2=<number>]
 
,[LCOSD1=<number>],[LCOSD2=<number>]
 
,[ITR=<number>],[SSTNO=<param>]
 
,[COSX=<number>],[SPDI=<number>]
 
,[SPDC1=<number>],[SPDC2=<number>]
 
,[INS=<param>]
 
,[RCBKB=<param>],[RCBKNA=<param>]
 
,[CBKBMAX=<number>],[BASICSVC=<param>]
 
,[IPCODEC=<param>],[IPADDR=<number>]
 
,[PASSWD=<string>],[USERID=<string>]
 
,[SECZONE=<string>],[FIXEDIP=<param>]
 
,[AUTHREQ=<param>],[SMGSUB=<param>]
 
,[DTMFCTRD=<param>];
Examples
1.
Connecting an OPTISET configuration directly to an SLMO with an OPTISET voice terminal with three add-on devices and a functional non-voice terminal of service FAX. The necessary S0 adapter OPTIS0A is implicitly configured by the AMO SBCSU.
Input:
ADD-SBCSU:STNO=3427,OPT=OPTI,CONN=DIR,PEN=1-1-67-1,DVCFIG=OPTISET&FAX,DPLN=0,ITR=0,COS1=5,COS2=6,LCOSV1=11,LCOSV2=12,LCOSD1=21,LCOSD2=22,REP=3,FPROT=SBDSS1,FOPTIDX=10;
Output:
H05: 3427 THIS STATION IS ASSIGNED AT PEN 1- 1- 67- 1
H35: 3427 THE TERMINAL ADAPTER OPTIS0A
FOR CONNECTING S0 DEVICES
MUST BE PLUGGED AT MAIN STATION NUMBER 3427.
H08: 3427 STATION RELEASED FOR CALL PROCESSING
2.
Expand the OPTISET configuration (of example no.1) with an OPTIP500. The OPTISET configuration to be expanded is specified with the parameter MAINO.
Input:
ADD-SBCSU:STNO=3428,OPT=OPTIEXP,MAINO=3427,DVCFIG=OPTIP500,DPLN=0,ITR=0,COS1=5,COS2=6;
Output:
H05: 3428 THIS STATION IS ASSIGNED AT PEN 1- 1- 67- 1
H35: 3428 THE TERMINAL ADAPTER OPTISPA
FOR CONNECTING THIS OPTIP500
MUST BE PLUGGED AT MAIN STATION NUMBER 3427.
H08: 3428 STATION RELEASED FOR CALL PROCESSING
3.
Expand the OPTISET configuration (of example no.2) with a MSN secondary station number
Input:
ADD-SBCSU:STNO=3428,OPT=MSN,MAINO=3427;
Output:
H22: 3428 MSN STATION NUMBER HAS BEEN ASSIGNED
FOR THE SERVICE FAX.
H08: 3428 STATION RELEASED FOR CALL PROCESSING
4.
Assign a MSN station number to the OPTISET configuration (of example no.3)
Input:
ADD-SBCSU:STNO=4999,OPT=MSN,MAINO=3427;
Output:
H22: 4999 MSN STATION NUMBER HAS BEEN ASSIGNED
FOR THE SERVICE FAX.
H08: 4999 STATION RELEASED FOR CALL PROCESSING
5.
Expand the Main Station Number (of example no.4) with a functional non-voice terminal with DTE service
Input:
ADD-SBCSU:STNO=3427,OPT=SVC,DVCFIG=DTE,DPROT=SBDSS1,DOPTIDX=10;
Output:
H05: 3427 THIS STATION IS ASSIGNED AT PEN 1- 1- 67- 1
H24: 3428 MSN STATION NUMBER HAS BEEN EXTENDED
BY THE SERVICE DTE.
H24: 4999 MSN STATION NUMBER HAS BEEN EXTENDED
BY THE SERVICE DTE.
6.
Configure an S0 bus connection with NI-BRI protocol via PNT (SLMQ3 module) with a SET600 voice terminal and functional non-voice terminals with DTE and FAX services.
Input:
ADD-SBCSU:STNO=3525,OPT=FBUS,CONN=PNT,DVCFIG=SET600&DTE&FAX,DPLN=0,ITR=0,COS1=5,COS2=6,LCOSV1=11,LCOSV2=12,LCOSD1=21,LCOSD2=22,SPROT=SBNIBRI,DPROT=SBNIBRI,FPROT=SBNIBRI,BASICSVC=UDI64;
Output:
H05: 3525 THIS STATION IS ASSIGNED AT PEN 1- 3- 67- 1
H08: 3525 STATION RELEASED FOR CALL PROCESSING
7.
Assign an S2 point-to-point connection as an external station.
Input:
ADD-SBCSU:STNO=3460,OPT=FPP,CONN=EXT,DVCFIG=S2PP,COS1=15,COS2=16,LCOSV1=11,LCOSV2=12,LCOSD1=21,LCOSD2=22,DPLN=0,ITR=0,PROT=SBDSS1,OPTIDX=10,INS=N;
Output:
H05: 3460 THIS STATION IS ASSIGNED AT PEN 1- 2- 25- 0
H09: 3460 THE STATION IS NOT ACTIVATED
${DocTitle}, ID: ${DocID}
 © 02/2025 Mitel Networks Corporation. -  All rights reserved.
 Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG.
 All other trademarks herein are the property of their respective owners.