166.2.2 CHANGE-SBCSU

The parameter STNO is mandatory. This parameter is used to specify the station to be changed. All other parameters are optional. However, at least one of these parameters must be declared. The parameter OPT must only be specified if OPT-specific parameters are to be changed.
MSN station numbers will also be processed!
The following users cannot be assigned a new station number (parameter NEWNO):
•
Users who have already been entered as a Route-to-Extension destination in an ACD Routing Table (AMO ACDRT).
•
Users for whom ACD attributes have already been set (AMO SDAT).
ZIEL/DSS entries are updated when station number is changed (parameter NEWNO).
Example: Station X is configured as DSS destination for station A
• If station A's number is changed, then the ZIEL/DSS entry is updated with new number of A and X stays as DSS destination.
• Is station X's number is changed, then the ZIEL/DSS entry is updated for station A with new number of X as DSS destination.
The parameters are divided into the following groups:
1.
General parameters (for all device types):
STNO, NEWNO, COS1, COS2, LCOSV1, LCOSV2, LCOSD1, LCOSD2, DPLN, ITR, SSTNO, COSX, SPDI, SPDC1, SPDC2, TRACE, ALARMNO, RCBKB, RCBKNA, CBKBMAX, HMUSIC, OPT, DTMFCTRD, DTMFBLK.
2.
Parameters for CorNet terminals:
IDCR, REP, SECR, DSSTNA, DSSTNB, DIGNODIS, OPTICA, OPTIDA, OPTICOM, HEADSET, HSKEY, CBKNAMB, TEXTSEL, CALLOG, PMIDX, COMGRP, APICLASS, SECAPPL, DNIDSP, DCFWBUSY, APMOBUSR, APPM.
3.
Parameter for IP terminals:
IPCODEC (for bandwidth calculation SIP and HFA subscribers in RESMAN), IPPASSW (for HFA subscribers only) and the SIP specific parameters IPADDR, PASSWD, USEID, SECZONE, FIXEDIP, AUTHREQ.
4.
Parameters for general analog terminal:
DFSVCANA, FLASH.
5.
Parameters for functional terminals:
SPROT, FPROT, DPROT, PERMACT, SOPTIDX, FOPTIDX, DOPTIDX, BASICSVC.
The protocol type parameters are ignored, unless a terminal has also been specified for the relevant service, e.g. DPROT for DTE.
The BASICSVC parameter is ignored, unless the NI BRI protocol has also been specified for a protocol type parameter, e.g. DPROT=SBNIBRI for DTE.
6.
Parameters for S0/S2/SIP point-to-point connections:
PERMACT, PROT, OPTIDX.
7.
Board-specific parameters
EXTBUS, ASYNCT, PATTERN, VPI, VCI, LWPAR.
If SECR has to be changed, the circuit must be locked. This can be done by AMO DSSU or by specifying parameter OFFTYPE in the CHANGE command.
Changes for the circuit specific parameters
ASYNCT, EXTBUS, IPPASSW, LWPAR, PERMACT, PATTERN, VPI, VCI
will only become effective after having the new data downloaded into the module.
Downloading will be triggered by
•
de- and re-activation “with unconditional loading” (e.g. RESTART-DSSU)
•
parameter OFFTYPE=DC (Default) or OFFTYPE=DI. The circuit must be in READY or UNACH state (can be interrogated by AMO SDSU). In UNACH state, data is loaded automatically when hierarchy becomes ready.

Restriction: please note, that parameters CLNTDESK and OSMO cannot be changed via CHANGE-SBCSU. In order to change them, the UFIP client has to be deleted and reconfigured with ADD new CLNTDESK/OSMO value. The OSMO UFIP consumes one OSMO license.
Procedure Overview
 
Command Code
Parameter
CHANGE-SBCSU
STNO=<number>
 
,[NEWNO=<number>],[COS1=<number>],[COS2=<number>]
 
,[LCOSV1=<number>],[LCOSV2=<number>]
 
,[LCOSD1=<number>],[LCOSD2=<number>]
 
,[DPLN=<number>],[ITR=<number>],[SSTNO=<param>]
 
,[COSX=<number>],[SPDI=<number>]
 
,[SPDC1=<number>],[SPDC2=<number>]
 
,[TRACE=<param>],[ALARMNO=<number>]
 
,[RCBKB=<param>],[RCBKNA=<param>],[CBKBMAX=<number>]
 
,[HMUSIC=<number>],[OFFTYPE=<param>]
 
,[BASICSVC=<param>]
 
 
 
|[OPT=FBUS]
 
,[SPROT=<param>],[FPROT=<param>],[DPROT=<param>]
 
,[PERMACT=<param>]
 
,[SOPTIDX=<number>]
 
,[FOPTIDX=<number>],[DOPTIDX=<number>]
 
,[EXTBUS=<param>],[ASYNCT=<number>]
 
,[DTMFCTRD=<param>],[PMIDX=<number>];
 
 
 
|[OPT=OPTI]}
 
,[IDCR=<param>],[REP=<number>]
 
,[SECR=<param>]
 
,[SPROT=<param>],[FPROT=<param>],[DPROT=<param>]
 
,[DSSTNA=<param>],[DSSTNB=<param>]
 
,[DIGNODIS=<param>],[SOPTIDX=<number>]
 
,[FOPTIDX=<number>],[DOPTIDX=<number>]
 
,[OPTICA=<number>],[OPTIDA=<number>]
 
,[ASYNCT=<number>],[OPTICOM=<param>]
 
,[PATTERN=<number>],[VPI=<number>],[VCI=<number>]
 
,[HEADSET=<param>],[HSKEY=<param>]
 
,[DFSVCANA=<param>]
 
,[CBKNAMB=<param>],[TEXTSEL=<param>]
 
,[CALLOG=<param>]
 
,[PMIDX=<number>],[COMGRP=<number>]
 
,[APICLASS=<param>],[SECAPPL=<number>]
 
,[DNIDSP=<param>],[DTMFCTRD=<param>]
 
,[DTMFBLK=<param>],[DCFWBUSY=<param>]
 
,[FLASH=<param>],[IPPASSW=<string>]
 
,[APMOBUSR=<param>],[IPCODEC=<param>]
 
,[APPM=<param>],[BLF=<param>],
 
,[USRID=<string>],[SECZON=<string>]
 
,[SUBIPADD=<string>];
 
 
 
|[OPT=CMI]
 
,[REP=<number>]
 
,[SPROT=<param>]
 
,[DSSTNA=<param>],[DSSTNB=<param>]
 
,[DIGNODIS=<param>]
 
,[SOPTIDX=<number>]
 
,[ASYNCT=<number>]
 
,[FPROT=<param>],[DPROT=<param>]
 
,[FOPTIDX=<number>],[DOPTIDX=<number>]
 
,[TEXTSEL=<param>],[DNIDSP=<param>]
 
,[PMIDX=<number>];
 
 
 
|[OPT=FPP]
 
,[PROT=<param>],[PERMACT=<param>],[OPTIDX=<number>]
 
,[LWPAR=<param>],[ASYNCT=<number>],[PMIDX=<number>]
 
,[IPCODEC=<param>],[IPADDR=<number>]
 
,[PASSWD=<string>],[USERID=<string>]
 
,[SECZONE=<string>],[FIXEDIP=<param>]
 
,[AUTHREQ=<param>],[SMGSUB=<param>]
 
,[DTMFCTRD=<param>];
OpenScape 4000 V10, Volume 1: AMO Descriptions, Service Documentation, Issue 20, ID: P31003H31A0S107207620
 © 05/2026 Mitel Networks Corporation. -  All rights reserved.
 Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG. All other trademarks herein are the property of their respective owners.