181.2.1 ADD SSCSU

The action ADD SSCSU is used to configure special subscriber terminals.
This action requires various criteria, incl.: the corresponding numbers in dialling evaluation (DAR=STN), a free set on the corresponding module and installed classes of service.
The parameter PEN defines the location (LTG-LTU-SLOT-CCT) at which the subscribers devices are connected with the number STNO. If this parameter is not used, a search is automatically performed for a free location in the system which matches the other parameter values.
Restrictions with PEN:
•
The device HTBMNGR can only be added to set 0
•
The device HTBPHONE can only be added to sets 1-30.
•
The extension connection HTBEXT can only be added to sets 31-254
•
The HTBLINE can only be added to sets 41-254
•
The device TCLOG is only configurable at circuit 0. Via circuit 0 the communication with the TC-Server is executed, telecommuters are not configured with TCLOG. This is exclusively done by the "Autoset Relocate" method using AMOs BCSU and SBCSU.
•
The extension connection TCEXT cannot be added to set 0
•
Signed off PENs are not allowed
Special aspect for entering ranges:
STNO parameters can be used for entering ranges and/or several individual values; this is not the case with the PEN parameter. In this case, the one entered PEN value is used as the starting value for the PEN search. Only one single number may be entered for subscribers to whom a partner number has to be allocated.
The device combination to be added at a connection is defined with the DVCFIG parameter. Type branching after OPT must be taken into consideration.
The non-voice device DTE can be used by the STN only if the basic authorization (BASIC) in his class of service ((COS1/COS2) has been entered for the corresponding service (AMO COSSU).
With TCEXT, the specified COS1/2 must contain the class of service SPECAR (Special Arrangement) .
With TCLOG and TCEXT, all parameters apart from PEN and STNO must be identical throughout the system. This cannot be checked by the AMO SSCSU.
If the parameter INS=YES (default setting), the added connection with all voice and any non-voice terminals must be forwarded for further administration to security technology. The corresponding device is put into service when all criteria have been met.
If the parameter INS=NO, the subscriber remains in a status which is not processed for security technology purposes. The device is not put "into operation", and it is only prewired in data terms. " With AMO DSSU, subsequent "ACTIVATE" or "DEACTIVATE" or "LOGON" is possible. AMO SDSU is used for the precise status display.
Partner numbers (PSTNO) must be specified for the device constellation HTBMNGR&DTE. However, the process of adding is only successful if adequate memory has been allocated with the AMO DIMSU (ADD-DIMSU: TEAMCONN=...).
A distinction is made between the following cases:
1.
Adding subscribers for Hicom Trading E:
•
Add a manager (OPT=HTB, DVCFIG=HTBMNGR&DTE,PSTNO=...).
•
Add a phone (OPT=HTB, DVCFIG=HTBPHONE&DTE).
•
Add an extension connection with service DTE (OPT=HTB, DVCFIG=HTBEXT&DTE).
•
Add an extension connection without service DTE (OPT=HTB, DVCFIG=HTBEXT).
•
Add a line (OPT=HTB, DVCFIG=HTBLINE).
2.
Add subscribers for telecommuting:
•
Add a logical telecommuter (OPT=TC, DVCFIG=TCLOG).
•
Add an extension connection (OPT=TC, DVCFIG=TCEXT).
Procedure Overview
 
Command code
Parameter
ADD-SSCSU
STNO=<number>
 
 
 
| ,OPT=HTB,[PEN=<number>],DVCFIG=<param>
 
,[PSTNO=<key-num>]
 
,COS1=<number>,COS2=<number>
 
,LCOSV1=<number,LCOSV2=<number>
 
,LCOSD1=<number,LCOSD2=<number>,[DPLN]=<number>]
 
,[ITR=<number>],[SSTNO=<param>],[COSX=<number>]
 
,[SPDI=<number>],[SPDC1=<number>],[SPDC2=<number>]
 
,[REP=<number>],[STD=<number>]
 
,[PROT=<param>],[OPTIDX=<number>]
 
,[INS=<param>],[ALARMNO=<number>]
 
,[RCBKB=<param>],[RCBKNA=<param>]
 
,[DSSTNA=<param>],[DSSTNB=<param>]
 
,[DIGNODIS=<param>];
 
 
 
| ,OPT=TC,[PEN=<number>],
 
| DVCFIG=TCLOG
 
,COS1=<number>,COS2=<number>
 
,LCOSV1=<number,LCOSV2=<number>,[DPLN]=<number>]
 
,[ITR=<number>],[COSX=<number>],[SPDC1=<number>]
 
,[SPDC2=<number>],[STD=<number>],[INS=<param>]
 
,[RCBKB=<param>],[RCBKNA=<param>],[DSSTNA=<param>]
 
,[DSSTNB=<param>],[HMUSIC=<number>];
 
| DVCFIG=TCEXT
 
,COS1=<number>,COS2=<number>
 
,LCOSV1=<number,LCOSV2=<number>,[DPLN=<number>]
 
,[ITR=<number>],[COSX=<number>],[PROT=<param>]
 
,[OPTIDX=<number>],[INS=<param>];
 
 
Examples
1.
Add the subscriber 2161 as HTBPHONE. The location is established by the AMO itself.
Input:
ADD-SSCSU:STNO=2161,OPT=HTB,DVCFIG=HTBPOHNE&DTE,COS1=5,COS2=6,LCOSV1=11,LCOSV2=12
,LCOSD1=21,LCOSD2=22;
Output:
H500: AMO SSCSU STARTED
H05: 2161 THIS STATION IS ASSIGNED AT PEN 1- 6- 55- 1
H08: 2161 STATION RELEASED FOR CALL PROCESSING
AMO-SSCSU-5 SPECIAL SUBSCRIBER CONFIGURATION OF SWITCHING UNIT
ADD COMPLETED;
2.
Add subscriber 2168 as TCLOG.
Input:
ADD-SSCSU:STNO=2168,OPT=TC,PEN=1-6-115-0,DVCFIG=TCLOG,COS1=5,COS2=6
,LCOSV1=11,LCOSV2=12;
Output:
H500: AMO SSCSU STARTED
H05: 2168 THIS STATION IS ASSIGNED AT PEN 1- 6-115-0
H08: 2168 STAION RELEASED FOR CALL PROCESSING
H44: 2168 FOR ALL SUBSCRIBERS WITH DVCFIG=TCLOG ALL PARAMETERS BESIDE
PEN AND STNO HAVE TO GET THE SAME VALUES.
AMO-SSCSU-5 SPECIAL SUBSCRIBER CONFIGURATION OF SWITCHING UNIT
ADD COMPLETED;
${DocTitle}, ID: ${DocID}
 © 02/2025 Mitel Networks Corporation. -  All rights reserved.
 Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG.
 All other trademarks herein are the property of their respective owners.