11.2.1. Configuring or Modifying a CC-AP/Survivable OpenScape 4000 SoftGate in OpenScape 4000 
The CC-AP/Survivable OpenScape 4000 SoftGate is always addressed with
the LTU number of the access point/OpenScape 4000 SoftGate in which it
is integrated.
Only the IP address for the IPDA LAN connection of the CC-AP/Survivable
OpenScape 4000 SoftGate and the operating mode of the Ethernet interface
are required as configuration data. All other parameters necessary for
IP communication are taken from the CBM configuration of HG 3575 of the
access point/OpenScape 4000 SoftGate.
Table 67. Configuration parameters derived for the CC-AP/Survivable OpenScape 4000 SoftGate
|
Parameter
|
“Network Link“ Access Point/OpenScape 4000
SoftGate
|
“Direct Link“ Access Point/OpenScape 4000
SoftGate
|
|
IP address
|
Directly configured
|
|
|
Netmask
|
HG 3575 network mask
APRT: TYPE=APNET
- NETMASK
|
OpenScape 4000 LAN segment network mask
SIPCO:
TYPE=LSNET - NETMASK
|
|
Default router
|
Default router in the network of the
access
point/OpenScape 4000 SoftGate
UCSU: UNIT=AP - APRTADDR
|
Default router in the network of the
access
point/OpenScape 4000 SoftGate
UCSU: UNIT=AP - APRTADDR
that
is usually the
default router of the OpenScape 4000 LAN segment
SIPCO:
TYPE=LSNET - DEFRT
|
|
VLAN tagging
|
STMIB: MTYPE=NCUI2 - TYPE=IFDATA
- VLAN
|
|
|
VLAN ID
|
STMIB: MTYPE=NCUI2 - TYPE=IFDATA
- VLANID
|
|
|
TOS byte for the
signaling
connection
|
STMIB: MTYPE=NCUI2 - TYPE=IFDATA
- TOSLAN
|
|
The Ethernet interface setting must be identical for
both connected interface partners (CC-AP/Survivable OpenScape 4000 SoftGate
or LAN switches or routers)!
IMPORTANT:
The setting of a fixed interface partner leads
to problems with the “Autonegotiate“ setting of the other partner.
IMPORTANT:
Incorrect settings cannot normally be detected
by the system and therefore go unreported. If one device is operating
in full duplex and the other in half duplex mode, this is not immediately
noticeable. Where there is a high payload, the device set to half duplex
will report a higher number of late collisions and the packet delay will
increase sharply.
IMPORTANT:
If the LAN port to which the CC-AP/Survivable
OpenScape 4000 SoftGate is connected does not support auto-negotiation,
or if it does not function reliably, the CC-AP/Survivable OpenScape 4000
SoftGate Ethernet interface must be set to fixed values.
In the example, the CC-AP/Survivable OpenScape 4000 SoftGate is configured
or modified in access point/OpenScape 4000 SoftGate 99.
The IP address is 192.168.23.199, the Ethernet interface is set to
10 Mbps, half duplex.
 |
Configuration Management > System Data
> IPDA > IPDA CC Access Point
Click Search and
select CC-AP/Survivable OpenScape 4000 SoftGate or create a New
one.
Set the IP Address and the Ethernet interface transmission
speed (Speed) and mode and Save.
|
 |
or
|
The modified data does not take effect until after you have used OpenScape
4000 Assistant Backup & Restore to copy the database to the CC-AP/Survivable
OpenScape 4000 SoftGate, and the CC-AP/Survivable OpenScape 4000 SoftGate
has accepted it.
Table 68. AMO APESU parameters in ADD or CHANGE branch under DATA=CCAP
|
AMO
|
Parameter
|
Sprache/ Language
|
Beschreibung/ Description
|
|
APESU
|
CCAPNUM
|
d
|
LTU-Nummer des Access Points/OpenScape 4000
SoftGates, in welchem der CC-AP/das Survivable OpenScape 4000 SoftGate
eingebaut ist.
|
|
CCAPNO
|
e
|
Line/Trunk Unit Number of the access point/OpenScape
4000 SoftGate, where the CC-AP/Survivable OpenScape 4000 SoftGate is
installed.
|
|
|
IPADR
|
d
|
IP Adresse des CC-AP/Survivable OpenScape 4000
SoftGate.
|
|
|
IPADDR
|
e
|
IP Address of the CC-AP/Survivable OpenScape
4000 SoftGate
|