35.3 Parameter Description


ADDRTYPE	Type of board addressing
	Type of input		single value, mandatory
	Possible values		ALL	all boards/modules
			PARTNO	board/module part number
			PEN	physical board/module address

CIR	Specification of circuit number
	Type of input	:	1 - 2 Single values, chained with &&, optional
	Possible values	:	numeric, 0-63
	With DIUS2 and SLMN modules, the statistic counters of the entire module are processed.
	In this case, the specified circuit number is ignored and advisory H29 issued.

DIA1	dia1
	Type of input		single value, mandatory
	Possible values		IW
			NW20
			PBB
			PSW
			TFA

DIA2	dia2
	Type of input		single value, mandatory
	Possible values		DTE
			FAX
			TTX
			VCE
			VTX

DISTYPE	Type of statistic to be displayed for TMDN board.
	Type of input		Single value, optional
	Possible Values		TOTAL	24 Hours total statistics.
			CURR	Current 15 min. statistics.
			ES	Errored seconds 24 hours interval statistics.
			FS	Failed seconds 24 hours interval statistics.
			BES	Bipolar errored seconds 24 hours interval statistics
			OES	Out of frame errored seconds 24 hours interval statistics
			US	Up-slips 24 hours interval statistics
			DS	Down-slips 24 hours interval statistics

FCTID	Function Id
	Type of input		Single value, optional
	Possible Values		numeric, 0-255

HFASW	HFA switching activities.
	Type of input		single value,optional
	Possible Values		NONE	No HFA specific activities.
			IPSTNBCK	Switch IP stations back.
			STBYRDY	Act as HFA standby board.
			SWITCH	Switchover ip stations to another board

LTG	Specification of the line trunk group
	Type of input	:	Single value, optional
	Possible value	:	1-32
	Default value	:	1

LTU	Specification of the line trunk unit
	Type of input	:	Single value, mandatory
	Possible values	:	numeric, 1-15, 17-99

OFFTYPE	Specifies the type of deactivate job
	Type of Input	:	Single value, optional
	Possible Values		DC	Deactivate Conditionally
			DI	Deactivate immediately
	Default Value	:	DC

ONTYPE	Specifies type of activate job
	Type of input	:	Single value, optional
	Possible Values		ACL	Activation with conditional loading
			AUL	Activation with unconditional loading
			ANL	Activation with no loading
	Default value	:	ACL

PARTNO	Part Number
	Type of input		single value, mandatory
	Possible Values		text, up to 10 characters

REFOFF	Switch reference clock generator
	Type of input	:	Single value
			optional
	Possible Values		Y	switch ref. clock generator off if applicable
			N	do not switch off ref. clock generator
			PROMPT	prompt parameter if ref. clock generator found
			Default value	PROMPT

RESET	Reset statistic option indicator for the TMDN board
	Type of input		Single value, optional
	Possible Values		YES	Reset all statistic counters and timers
			NO	Do not reset the counters.
			DEFAULT	NO

SLOT	Specification of the slot in the LTU.
	The slots are consecutively numbered from left to right. Of the slots occupied by the module, the lowest number must be specified. (Each 6 slots form a mounting location; therefore, the only slots that are valid here are 1, 7, 13, 19, etc. Restriction: some modules, e.g., SLMA, occupy two mounting locations, so that some elements in this sequence are not valid slots; slot for LTUC: cannot be switched in this case!)
	Type of input	:	1 to 2 single values, concatenated wit &&, mandatory
	Possible values	:	1-121	A suitable module must be configured for the slot addressed by PEN (AMO BCSU).

WTIME	Wait time between switching off and switching on in seconds.
	Type of input		Single value, optiona
	Possible values		0-20
			DEFAULT	1

OpenScape 4000 V10, Volume 1: AMO Descriptions, Service Documentation, Issue 5, ID: P31003H31A0S107057620

© 09/2025 Mitel Networks Corporation. - All rights reserved.
Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG. All other trademarks herein are the property of their respective owners.