75.2.2 CHANGE-DIDCR

The elements within the SRT table, or a DIDCR table can be changed by using the function CHANGE-DIDCR.

- the actual digit string for single or multiple field entries in the selected DIDCR table. Parameter RULEIDX may not be a range in CHANGE command.

- the actual SID/ANI data for a single field entry or for a range of field entries for a Network Service and a specified RULEIDX.

- the actual RULEIDX in a SRT table.

When initiating this verb the following checks are performed. Each check produces a reaction and a prompt or end.

Table 12: CHANGE-DIDCR Error Messages
Check Performed	Reaction	Prompt or End
A CHARACTER OTHER THAN (0:9),*,# WAS USED IN THE VALUE FOR DIGITS	F1	DIGITS
THE ENTERED DIDTAB DOES NOT EXIST	F3	End
THE ENTERED DIGIT STRING FOR TBLIDX IS AN INVALID LENGH	F5	DIGITS
THE ENTERED SERVICE RULE TABLE IS CONFIGURED BY PRI SERVICE TRUNKS	F6	End
TOO MANY VALUES FOR PARAMETER DIGITS HAS BEEN ENTERED (UP TO 9 DIGITS CAN BE ENTERED AT ONE TIME)	F10	End
NO CHANGE WAS MADE ALL DATA ENTERED IS THE SAME AS THE ACTUAL DATA	F13	End
SID/ANI DATA CAN ONLY BE USED WITH THE SERVICES INWATS,VPN,SDS,PPC900	F14	End
THE NUMBER OF VALUES ENTERED FOR TBLIDX AND DIGITS MUST BE THE SAME	F15	DIGITS
TOO MANY TABLE INDICES ENTERED (NO MORE THAN 9 MAY BE ENTERED)	F16	TBLIDX

If the craftsperson changes the RULEIDX in a SRT table, a check will be made to ensure that the entered RULEIDX points to a DIDCR table which is initialized. The same check will be made for the SID/ANI data information which belongs to this RULEIDX. If one of these tables is not initialized , the corresponding advisory message is displayed: CHANGE-DIDCR Advisory table

Procedure Overview

Table 13: CHANGE-DIDCR Advisory Messages
Check Performed	Reaction	Prompt or End
SID/ANI REQUEST DATA ASSOCIATED WITH THE SERVICE RULE TABLE AND SERVICE TYPE HAS BEEN INITIALIZED TO "NOREQU"	H6	End
THE DIDCR TABLE REFERENCED BY THE ENTERED RULEIDX DOES NOT EXIST (TOTDIG = 0)	H8	End

|Command Code|Parameters |
+------------+-------------------------------------------------+
|CHANGE-DIDCR||TYPE=DID,RULEIDX=<NUMBER>,TBLIDX=<NUMBER>, |
| | DIGITS=<number>; |
| | |
| ||TYPE=SRT,SRTABLE=<number>,NETSVC=<param>, |
| | RULEIDX=<number>; |
| | |
| ||TYPE=SVC,NETSVC=<param>,RULEIDX=<number>, |
| | SVCIDX=<number>,SVCDATA=<string>; |
| | |

Example 1:

Change elements in the DIDCR table 2.

Input:

CHANGE-DIDCR:DID,2,91&&99,101&102&103&104&105&106&107&108&109;

Output:

CHANGE-DIDCR:DID,2,91&&99,101&102&103&104&105&106&107&108&109;
H500: AMO DIDCR STARTED
AMO-DIDCR-... DIRECT INWARD DIAL DIGIT_CONVERSION_RULE
CHANGE EXECUTED;

Input:

CHANGE-DIDCR:DID,2,52&&55,25&355&4555&55555;

Output:

CHANGE-DIDCR:DID,2,52&&55,25&355&4555&55555;
H500: AMO DIDCR STARTED
AMO-DIDCR-... DIRECT INWARD DIAL DIGIT_CONVERSION_RULE
CHANGE EXECUTED;

Example 2:

Change the RULEIDX in the SRT table 1 for Network Service
VPN and INTLWATS.

Input:

CHANGE-DIDCR:SRT,1,VPN,2;

Output:

CHANGE-DIDCR:SRT,1,VPN,2;
H500: AMO DIDCR STARTED
H6: SID/ANI DATA ACCESSED BY SERVICE SDN IS INITIALIZED TO "NOREQU".
AMO-DIDCR-... DIRECT INWARD DIAL DIGIT_CONVERSION_RULE
CHANGE EXECUTED;

Input:

CHANGE-DIDCR:SRT,1,INTLWATS,2;

Output:

CHANGE-DIDCR:SRT,1,INTLWATS,2;
H500: AMO DIDCR STARTED
AMO-DIDCR-... DIRECT INWARD DIAL DIGIT_CONVERSION_RULE
CHANGE EXECUTED;

Example 3:

Change the SID/ANI Data for RULEIDX 1 and Network Service INWATS.

Input:

CHANGE-DIDCR:SVC,INWATS,1,0&&15,ANI;

Output:

CHANGE-DIDCR:SVC,INWATS,1,0&&15,ANI;
H500: AMO DIDCR STARTED
AMO-DIDCR-... DIRECT INWARD DIAL DIGIT_CONVERSION_RULE
CHANGE EXECUTED;

Input:

CHANGE-DIDCR:SVC,INWATS,1,16&&21,SID;

Output:

CHANGE-DIDCR:SVC,INWATS,1,16&&21,SID;
H500: AMO DIDCR STARTED
AMO-DIDCR-... DIRECT INWARD DIAL DIGIT_CONVERSION_RULE
CHANGE EXECUTED;

Input:

CHANGE-DIDCR:SVC,INWATS,1,33,SIDPREF;

Output:

CHANGE-DIDCR:SVC,INWATS,1,33,SIDPREF;
H500: AMO DIDCR STARTED
AMO-DIDCR-... DIRECT INWARD DIAL DIGIT_CONVERSION_RULE
CHANGE EXECUTED;

OpenScape 4000 V10, Volume 1: AMO Descriptions, Service Documentation, Issue 5, ID: P31003H31A0S107057620

© 09/2025 Mitel Networks Corporation. - All rights reserved.
Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG. All other trademarks herein are the property of their respective owners.