128.4 Error messages and advisories

128.4.1 Error messages


F01:	A WAML BOARD WITH THIS PEN HAS NOT BEEN CONFIGURED
	No WAML board has been added for the specified address (LTG, LTU, EBT) or the address is incorrect or invalid. You must use the same address that was used for adding a WAML by means of AMO BCSU.
F02:	THERE ARE FORMAL ERRORS IN THE STATION NUMBER @@@@@@@@@@@@@@@@@@@@@@
	The specified station number contains invalid characters. Only digits in the 0 - 9 range may be used.
F03:	THE VALUE ’NONE’ FOR PARAMETER ’FIREWALL’ MUST BE ENTERED AS SINGLE VALUE
	The NONE parameter value must not be specified together with other values. This combination is meaningless!
F04:	TABLE ’@@@@@@@@’ IS FULL, NO ENTRY POSSIBLE
	All table elements in the table specified are already being used. In order to be able to add another entry, you must first delete an entry that is no longer needed.
F05:	THERE IS ANOTHER WAML BOARD WITH ACCESS RIGHTS TO THE ATLANTIC LAN
	In a system, only one WAML can access the ADP via the Atlantic LAN. This connection already exists and, therefore, cannot be configured here.
F06:	WHEN A NETMASK HAS BEEN ENTERED AN IP-ADDRESS IS REQUIRED ENTER PARAMETER ’@@@@@@@@’
	For the DISPLAY and REGENERATE actions, you must specify an IP address if you wish to use a network mask.
F07:	THERE ARE FORMAL ERRORS IN THE IP-ADDRESS @@@.@@@.@@@.@@@
	The IP address specified is errored. Only digits in the 0 - 9 range may be used. Furthermore, the address must comprise 4 parts separated by dots; none of these values may exceed 255 and at least one part of the address must equal ’0’.
F08:	DATA HAVE NOT BEEN LOADED
	The load job was rejected by the PIT with a negative load result (DB_LC_LR_DATA_NOT_LOADED). This was caused by the fact that, for reasons that cannot be specified further, the PIT could not load data to the board (e.g. no connection to board). One solution might be to deactivate (DEACTIVATE-BSSU) and activate (ACTIVATE-BSSU) the board, since this also serves to load the board.
F09:	TO EACH STATION NUMBER ITS USAGE HAS TO BE ENTERED
	When adding or changing station number(s), you must specify the usage type and the STNOx and INOUTCHx parameters must be specified together. This determines whether a station number can be used for incoming calls only or can also be used for the WAML’s callback function.
F10:	THE SPECIFIED IP-ADDRESS HAS NOT BEEN CONFIGURED
	The IP address specified in the command is not contained in the table selected. The address must first be configured in the table by means of the ADD action.
F11:	THE ENTERED NETWORK INTERFACE HAS NOT BEEN CONFIGURED
	The network interface specified in the command is not contained in the table selected. The interface must first be configured in the table by means of the ADD action.
F12:	THE ENTERED IP-ADDRESS HAS BEEN ALREADY CONFIGURED
	The IP address specified in the command is contained in the table selected. You can reconfigure this address by means of the CHANGE action or delete it using the DELETE action.
F13:	DATA HAVE BEEN ALREADY CONFIGURED
	The data in the global parameter table is already configured. You can change this data by means of the CHANGE action or delete the entire table using the DELETE action.
F14:	THE ENTERED NETWORK INTERFACE HAS BEEN ALREADY CONFIGURED
	The network interface specified in the command is contained in the table. You can reconfigure this interface by means of the CHANGE action or delete it from the table using the DELETE action.
F15:	NO DATA HAVE BEEN CONFIGURED
	The relevant table contains no entries; it is empty. You can configure entries by means of the ADD action.
F16:	NO ANSWER FROM @@@
	Instead of an acknowledgment of the load job, a message was received from an invalid task. It may be possible to correct the problem by repeating the job.
F17:	LTU NUMBER @@@ DOES NOT HAVE ADMISSIBLE VALUE
	The LTU number specified is not within the limiting values permitted in the system.
F18:	THERE ARE FORMAL ERRORS IN THE MAC-ADDRESS @@.@@.@@.@@.@@.@@
	The MAC address specified is errored. Only characters from 0 to 9 and from A to F may be used. Moreover, the address must comprise 6 parts separated by dots; none of these values may exceed ’FF’ and at least one part of the address must equal ’0’.
F19:	NO PLAUSIBLE EVENT FROM @@@
	The acknowledgment from the task specified contains an incorrect event code. It may be possible to correct the problem by repeating the command.
F20:	THE IP-ADDRESS 255.255.255.255 IN PARAMETER @@@@@@@@ IS NOT ALLOWED
	The IP address specified cannot be used in the parameter named.
F21:	THE DYNAMIC BOARD-ID FOR WAML IS NOT AVAILABLE
	This error message could indicate an inconsistency in the board’s ADD data. Using ’DISPLAY-BCSU:TBL,..’, check whether the board has been properly added and is operating. If yes, repeat the command.
F22:	LOW WATERMARK MUST BE LESS THAN HIGH WATERMARK
	An invalid limiting value was specified for the low watermark or high watermark.
F23:	DATA HAVE NOT BEEN LOADED BECAUSE THE BOARD IS NOT IN STATE ’READY’
	The relevant load job could not be executed because the WAML is not operating. Using ’DISPLAY-BCSU:TBL,..’, check whether the board has been properly added and determine its current status.
F24:	THIS IP-ADDRESS IST NOT ALLOWED FOR ATLANTIC-LAN. THE FOURTH PART OF THE IP-ADDRESS MUST HAVE EVER THE VALUE ’4’.
	The value of the fourth part of the IP address for the Atlantic LAN interface on each WAML is parmanently defined as ’4’. All other values are therefore invalid.
F25:	IT WAS NOT POSSIBLE TO READ THE WAML MAC-ADDRESS, THE BOARD IS NOT IN STATE ’READY’
	Due to a dump problem on the WAML board, it was not possible to read a MAC address. Using ’DISPLAY-BCSU:TBL,..’, check whether the board has been properly added and determine its current status.

F26:	THE ENTERED NET MASK CAN NOT BE USED IF DESTINATION=NET
	At network IP addresses the network mask 255.255.255.255 is not allowed to use. Type in a valid network mask.
F27:	THE ENTERED STATION NUMBER IS ALREADY USED BY ANOTHER WAML BOARD AT PEN <ltg>.<ltu>.<slot>.
	The WAML station number added only once. Each WAML board must have its own station number.
F28:	THE ENTERED IP-ADDRESS IS ALREADY USED BY ANOTHER WAML BOARD AT PEN <ltg>.<ltu>.<slot> TO ACCESS THE NETWORK INTERFACE <param>.
	Each IP address must be unique within a system. Take care of it, if you try to add more than one WAML board.
F29:	THE PARAMETER VALUE 'OUT' MAY BE ENTERED ONLY FOR ONE STATION NUMBER.
	The WAML uses the station number with specified OUT flag for its callback function.

OpenScape 4000 V10, Volume 1: AMO Descriptions, Service Documentation, Issue 5, ID: P31003H31A0S107057620

© 09/2025 Mitel Networks Corporation. - All rights reserved.
Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG. All other trademarks herein are the property of their respective owners.