128.4.2 Advisories

 
H01:
THERE ARE NO DATA CONFIGURED IN TABLE ’@@@@@@@@’
 
The relevant table contains no entries; it is empty. You can configure entries by means of the ADD action.
H02:
THE IP-ADDRESS @@@.@@@.@@@.@@@ OF THE NEXT ROUTER DO NOT CORRESPOND
TO A WAML INTERFACE.
 
The IP address specified does not match the IP address of a WAML network interface or the WAML’s network interface(s) has/have not yet been added. NO data can currently be routed with this IP address. You can use the ’DISPLAY-LANC:TABTYPE=NETWORK;’ command to view the configured network interfaces (IP addresses).
H03:
BEFORE USING ACTION 'CHANGE, THE TABLE @@@@@@@@ MUST BE ADMINISTERED WITH THE VERB 'ADD'
H04:
TABLE ’@@@@@@@@’ - NO DATA FOUND
 
The table specified contains no entries that match the command entered. The relevant entry was not found.
H05:
USER ADVISORY: THIS ACTION POSSIBLY MAY RESULT IN AN INCONSISTENT
CONFIGURATION OF THE LAN. FOR MORE INFORMATION READ THE AMO DESCRIPTION.
 
Changing these tables without taking into account the cross-references may result in an inconsistency in the LAN connectivity configuration. This could mean that when, for example, the IP routing table is deleted, no data packets can be assigned to a WAML interface by means of the WAML router function. Deleting a firewall table may mean that when a check is activated, the check result will be negative and a data connection will be rejected. Under such circumstances, it is the user’s responsibility to determine the effect of his or her command; in such cases, the AMO LANC can provide no support.
H07:
CHANGED CONFIGURATION DATA AVAILABLE - LOAD WAML BOARD WITH COMMAND
’EXEC-LANC’ REQUIRED.
 
Changes were made to the WAML configuration data since the last load command. In order for these changes to become valid, they must be loaded to the board by means of the ’EXEC-LANC:...’ command.
H08:
THE NETWORK INTERFACE(S) @@@@@@@ @@@@@@@ @@@@ (PARAMETER ’ACTNETIF’)
IS/ARE NOT CONFIGURED IN THE NETWORK INTERFACE TABLE.
 
This message means that the network interfaces specified were activated in the global parameter table but have not yet been added to the network interface table. You can configure the specified network interfaces by means of the ’ADD-LANC::TABTYPE=NETWORK,..’ command.
H09:
THE NETWORK INTERFACE(S) @@@@@@@ @@@@@@@ @@@@ (PARAMETER ’ACTNETIF’)
IS/ARE STILL ACTIVE IN THE GLOBAL TABLE.
 
This message means that the network interface(s) specified has/have been deleted from the network interface table but is/are still activated in the global parameter table. You can deactivate the specified network interface(s) by means of the ’CHANGE-LANC:TABTYPE=GLOBAL, ACTNETIF=...’ command. At least one active interface is required for operating the WAML.
H10:
THE IP-ADDRESS IS CONFIGURED AS HOST, SO THE NET MASK (IPNMASK) IS NOT EFFECTIVE.
 
At host IP addresses the network mask is ignored and automatically the default value 255.255.255.255 shall be written in the database.
H11:
THE IP-ADDRESS @@@.@@@.@@@.@@@ IS USED BY THE WAML AS DEFAULT ROUTER.
 
It is indicated that an entry in the IP routing table with the “wild card address” 0.0.0.0 has been added or changed.
 
 
 
OpenScape 4000 V10, Volume 1: AMO Descriptions, Service Documentation, Issue 5, ID: P31003H31A0S107057620
 © 09/2025 Mitel Networks Corporation. -  All rights reserved.
 Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG. All other trademarks herein are the property of their respective owners.