153.5 Parameter description


BOARD	Module type for determination of class of table
	Type of input	:	Single value
			mandatory (CHANGE)
			optional (CHANGE,REGENERATE)
	Possible Values	:	LEVEL = BOARD	CDG DIUC DIUC64 DIUN2 DIUN4 DIU2U DIUS2 NCUI SLMB16 SLMC SLMO SLMQ SLMS SLMU16 SLMY STHC STMA2T STMAS STMI STMIHFA STMIIGW STMI2IGW TMDN VCM WAML1 WAML2 OTHER
			LEVEL = BOARD1	DIUC DIUC64
			LEVEL = BOARD2	DIUC64
	The value OTHER is not valid for the actions CHANGE and REGENERATE.

COUNTACT	Counter action
	Action on reaching counter limit
	Type of Input	:	Single value, optional
	Possible Values	:	0	Counter remains unchanged
			2 to 254	Reset by n
				(only even values permitted)
			255	Reset to 0

CPTYPE	CP device type
	Type of Input	:	Single value, linked single values,
			ranges, up to 12 values, hexadecimal,
			optional
	Possible Values	:	0 to 48
	Default value	:	all device types

DECREM	Decrement
	Decrement on reaching the interval defined with TIME
	Type of Input	:	Single value, optional
	Possible Values	:	0	Counter remains unchanged
			2 to 254	Reset by n
				(only even values permitted)
			255	Reset to 0

DHTYPE	DH device type
	Type of Input	:	Single value, linked single values,
			ranges, up to 12 values, hexadecimal,
			optional
	Possible Values	:	0 to 5A
	Default value	:	all device types

ERROR	Class of errors where the command is effective
	Type of Input	:	1 to 12 single values, concatenated with &,optional (DISPLAY, TYPE=VECO)
			1 to 13 single values, concatenated with &,optional (CHANGE, TYPE=VECOLEVL / VECOSWCH)
			1 to 4 single values, concatenated with &,optional (REGENERATE, TYPE=VECO)
	Possible Values	:	CPBCHL	cp_bchl
			CPDEV	cp_dev
			CPKONS	cp_kons
			CPNOANSW	cp_no_answ
			CPNWCR	cp_nwcr
			CPSBCRI	cp_sbcri
			DHCONF	dh_conf
			DHDEV	dh_dev
			DHLINE	dh_line
			DHLINK	dh_link
			DHNWCR	dh_nwcr
			DHSBCRI	dh_sbcri
			DHSIU	dh_siu
	Default value	:	all error classes

FAULT	Fault counter in table
	Type of Input	:	Single value, optional
	Possible Values	:	COUNT1	counter 1
			COUNT2	counter 2
			COUNT3	counter 3; only LEVEL=BOARD1 or BOARD2
			COUNT4	counter 4; only LEVEL=BOARD1 or BOARD2
			Meanings for levels BOARD and CIR:
			COUNT1 Pairs counter
			COUNT2 Flood of messages
			Meanings for levels BOARD1 and BOARD2:
			COUNT1 local alarms
			COUNT2 remote alarms
			COUNT3 AIS (Alarm Indication Signal)
			COUNT4 automatic removal of module
	Default value	:	all counters

LEVEL	Table level
	Type of Input	:	Single value, mandatory (CHANGE,TYPE=CTRLTAB/LOCKTIM/RESET/STABTIM; DISPLAY,TYPE=COUNTER/CTRLTAB; REGENERATE,TYPE=CTRLTAB)
			Single value, optional ( REGENERATE, TYPE=LOCKTIM/ STABTIM)
	Possible Values	:	BOARD	Module level
			BOARD1	Module level 1
			BOARD2	Module level 2
			CIR	Circuit level
			DEV	Device level
			LTUC	LTUC-level
			For CHANGE/REGENERATE, TYPE=CTRLTAB only BOARD and CIR are permissible.
			For CHANGE, TYPE=RESET, only BOARD1 and BOARD2 are permissible.
			For DISPLAY, TYPE=COUNTER and CTRLTAB only BOARD, BOARD1, BOARD2 and CIR are permissible.
			For CHANGE/REGENERATE, TYPE=LOCKTIM and STABTIM, BOARD, CIR, DEV und LTUC are permissible.
LINE	Line Type for Determination of Class of Table
	Type of Input	:	Single value, mandatory (CHANGE, TYPE=CTRLTAB, LEVEL=CIR)
			Single value, optional (DISPLAY/ REGENERATE, TYPE=CTRLTAB, LEVEL=CIR)
	Possible Values	:	CDG	cdg
			DIUC	diuc
			DIUC64	diuc64
			DIUN2	diun2
			DIUN4	diun4
			DIUS2	dius2
			NCUI	ncui
			OTHER	all other
			SLMB16	slmb16
			SLMC	slmc
			SLMO	slmo
			SLMQ	slmq
			SLMS	slms, slms2, stmd2 (q2163-x100)
			SLMU16	slmu16
			SLMY	slmy
			STHC0	sthc (sircuit 0-15)
			STHC16	sthc (circuit 16-19)
			STMANW20	stma networking 2.0
			STMANW21	stma networking 2.1
			STMAPSW	stma port-switching
			STMI	stmi
			STMI2IGW	stmi2-igw (HG3550-2)
			TMDNBOS	tmdn64 bos
			TMDNMOS	tmdn64 mos
			VCM	vcm

MAXCOUNT	Threshold of statistics counter
	Type of Input	:	Single value,	optional (TYPE = CTRLTAB)
				mandatory (TYPE = VECOLEVL)
	Possible Values	:	0	Counter is deactivated
			1 to 255	Threshold is n
				(at TYPE = CTRLTAB only odd values permitted)

MODE	Operation mode of VECO
	Type of Input	:	Single value, optional
	Possible Values	:	ONWMSG	veco statistics with periodic statistics printout
			ONWOMSG	veco statistics without periodic printout
			STATOFF	VECO Statistics off
	Default value	:	no change of mode

PEN	Pen of a module or of a circuit
	Type of Input	:	3 single values, linked with -, mandatory at LEVEL=BOARD, BOARD1 or BOARD2
		:	4 single values, linked with -, mandatory bei LEVEL=CIR
	Possible Values	:	g-uu-sss for LEVEL = BOARD, BOARD1 or BOARD2
			gg-u-sss-cc for LEVEL = CIR
			g	= LTG 1 (no other value)
			uu	= LTU 1 to 15 in HHS (Host Shelf)
				16 not defined
				17 to 99 in P (Access Point Shelf)
			sss	= Slot 1 to 121
			cc	= Circuit number 0 to 254
A suitable module must be configured to the slot addressed by PEN (AMO BCSU).
The possible LTU and Slot values for PEN depend on the systems architecture and can be found in the BCSU AMO description.
The possible Line values depend on the module type and its functionality. They can be listed using DISP-BCSU: TYPE=PEN1 [,LTG=, LTU=, SLOT=, CCT=]; which will also output the actual PEN status (e.g. NOT CONNECTED).

PERIOD	Distance of periodic outputs (hours)
	Type of Input	:	Single value, optional
	Possible Values	:	1 - 65535
	Default value	:	24

STIM	Stabilisation time
	Type of Input	:	Single value, mandatory
	Possible Values	:	10 - 30

SWITCH	State for single error class
	Typ of Input:	:	Single value, mandatory
	Possible Values	:	ON	Threshold signalling on
			OFF	Threshold signalling off

TIME	Size of time interval as multiple of Basic time (currently 60 seconds)
	Type of Input	:	Single value, optional
	Possible Values	:	1 to 65535

TIM1...TIM 8	Lock time 1...8
	Type of Input	:	Single value, optional
	Possible Values	:	1 - 60 (TIM1) 0 - 60 (TIM2 - TIM8)
	The Parameters TIM1...TIM8 form a group. At least 1 parameter is to be entered.

TYPE	Branch Parameter
	Type of Input	:	Single value, optional (REGENERATE)
			Single value, mandatory (other branches)
	Possible Values	:	CTRLTAB, RESET, VECOGEN, VECOLEVL, VECOSWCH, LOCKTIM, STABTIM (CHANGE)
			COUNTER ,CTRLTAB, VECO, LOCKTIM, STABTIM (DISPLAY)
			CTRLTAB, VECO, LOCKTIM, STABTIM, ALL (REGENERATE)
	Default value	:	ALL

OpenScape 4000 V10, Volume 1: AMO Descriptions, Service Documentation, Issue 5, ID: P31003H31A0S107057620

© 09/2025 Mitel Networks Corporation. - All rights reserved.
Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG. All other trademarks herein are the property of their respective owners.