154.6.4 Appendix 2, Part 4: Initblocks 61 till 80

Longtimer	Default (ms)	Description	Remark
L1	600	Guard time for release after preemption (600- 5800 ms)
L2	326	Minimum time for recognition of 345ms valid pulse (315- 375 ms)
L3	345	Time for preemption transmission 345ms pulse (300- 390 ms)
L4	0	reserve
L5	0	reserve
L6	0	reserve
L7	0	reserve

Shorttimer	Default (ms)	Description	Remark
S1	34	Total tolerance time (+/-17ms) for recogniton of pulse (8- 60 ms)
S2	81	Minimum time for recognition of 100ms valid pulse (70- 130 ms)
S3	100	Time for preemption transmission 100ms pulse (70- 130 ms)
S4	0	reserve
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve

Parameter	Default	Description		Remark
P1	0	Trunk used as MLPP trunk
		0	Not used as MLPP trunk
		1	Used as MLPP trunk
P2	0	reserve
P3	0	reserve
P4	0	reserve
P5	0	reserve
P6	0	reserve
P7	0	reserve
P8	0	reserve
P9	0	reserve
P10	0	reserve
P11	0	reserve
P12	0	reserve
P13	0	reserve
P14	0	reserve

Longtimer	Default (ms)	Description	Remark
L1	5000	maximum recognition time for seizure acknowledge pulse (40-10000 ms)
L2	180	maximum recognition time for release guard (40- 500 ms)
L3	120	minimum recognition time for clear forward or release backward (0-600 ms)
L4	85	transmission time of release guard (40- 500 ms)
L5	100	minimum recognition time for seizure (0- 500 ms)
L6	200	minimum recognition time for release acknowledge (0- 1000 ms)
L7	400	minimum transmission time for answer (0- 1000 ms)

Shorttimer	Default (ms)	Description	Remark
S1	80	min. recognition time for seizure acknowledge pulse (40- 200 ms)
S2	100	min. transmission time for clear backward before release guard (0- 255 ms)
S3	30	supervision time for glare seizure 0 2.4 s 1 - 255 time in ms
S4	140	transmission time for wink start 0 300ms 60 - 255 time in ms
S5	100	minimum transmission time for delay dial (0- 255 ms)
S6	60	minimum recognition time for metering pulse (20 - 255 ms)
S7	0	alarm recognition (only for Q2092-X200) 0 without alarm recognition 1 with alarm recognition
S8	28	number of override impulses (0-50)
S9	0	allowed time for override impulse 0 without override 1 override without time limit (valid after eod_busy, eod_free and before end-of-dial) 2-60 s time in sec.
S10	0	supervision time for ready line signal (seizure ackn.) (0-6s) 0 no supervision of ready signal 1-6 time in sec
S11	0	supervision time for clearback line signal (0-6s) 0 no supervision of ready clearback signal 1-6 time in sec
S12	1 s	retry timer for active phase of test procedure - time in sec. (1-10 s)
S13	60 s	retry timer for passive phase of test procedure - time in sec. (1- 255 s)
S14	1 s	supervision time for clear forward (blocking or alarm recognition 0 no supervision of blocking 1- 255 supervision in sec

Parameter	Default	Description		Remark
P1	0	seizure acknowledge
		0	immediate dial
		1	delay dial
		2	Wink Start
		3	continuous signal
P2	0	test procedure
		0	no test procedure
		1	with test procedure
P3	0	signalling direction
		0	bothway directed (glare seizure: priority of incoming seizure)
		1	outgoing directed
		2	incoming directed
		3	bothway directed (glare seizure: release of line)
P4	0	conversation supervision
		0	endless (no supervision)
		1-255	multiplied with 30 sec.
P5	1	guard time before new outgoing seizure in seconds
		0	500 msec
		1-255	multiplied with 1 sec.
P6	0	dial tone recognition
		0	no dial tone recognition
		1	dial tone recognition
P7	120	answer supervision in case of outgoing directed traffic
		0	no answer supervision
		1-255	answer supervision in seconds
P8	1	blocking as line signal, if bothway or incoming directed traffic
		0	without blocking as line signal
		1	with blocking as line signal
P9	0	metering pulse recognition
		0	no metering pulse recognition
		1	metering pulse recogniton
P10	0	release guard as line signal
		0	without release guard as line signal
		1	with release guard as line signal
P11	1	answer as line signal
		0	without answer as line signal
		1	with answer as line signal
P12	0	dialing method
		0	without digit pulsed
		1	digit pulsed
P13	2	special clear backward with pseudo-answer and backward release on incoming side before answer
		0	not used
		1	after called subscriber busy
		2	after release from DH
		3	after called subscriber busy or release from DH
P14	0	inverse signaling
		0	normal signalling (idle state : M=OFF / E=OFF)
		1	inverse signalling (idle state : M=ON / E=ON)
		2	inverse signalling only on E-wire (idle state : M=OFF / E=ON)
		3	inverse signalling only on M-wire (idle state : M=ON / E=OFF)

Longtimer	Default (ms)	Description	Remark
L1	5000	supervision time for start dial signal after seizure on outgoing traffic (40-10000 ms)	out
L2	625	transmission time for long impulse on outgoing traffic (200- 2000 ms)	out
L3	300	transmission time for long pause on incoming traffic (clear back pulse train) (100-1000 ms)	in
L4	270	minimum recognition time for long impulse on incoming traffic (S3 + S4 + L4) (100-1000 ms)	in
L5	2000	maximum recognition time for long impulse on incoming traffic (L5 > S3 + S4 + L4) (4000- 5000 ms)	in
L6	400	recognition time for long pause on outgoing traffic (clear back pulse train) (50- 1000 ms)	out
L7	0	reserve

Shorttimer	Default (ms)	Description	Remark
S1	100	transmission time for short impulse on incoming and outgoing traffic (40- 250ms)	out
S2	100	transmission time for short pause on incoming traffic (0- 255 ms)	in
S3	70	minimum recognition time for short impulse on incoming and outgoing traffic (40- 250 ms)	in/out
S4	60	maximum recognition time for short impulse on incoming and outgoing traffic (S3 + S4) (20- 250 ms)	in/out
S5	150	recognition time for short pause on outgoing traffic (EOD_free, EOD_busy) (20- 250 ms)	out
S6	50	supervision time for glare seizure on outgoing traffic (20- 255 ms)	in
S7	0	reserve
S8	0	reserve
S9	0	reserve
S10	0	reserve
S11	0	reserve
S12	0	reserve
S13	0	reserve
S14	0	reserve

Parameter	Default	Description		Remark
P1	0	start dial line signal		out
		0	no start dial line signal
		1	with start dial line signal
P2	0	restore procedure, if bothway or outgoing directed traffic		out
		0	no restore procedure
		1	with restore procedure (put in service)
		2	with restore procedure (line alarm)
		3	with restore procedure (in service and line alarm)
P3	0	signalling direction		in/out
		0	bothway directed (glare seizure: priority of incoming seizure)
		1	outgoing directed
		2	incoming directed
		3	bothway directed (glare seizure: release of line)
P4	0	end-of-dial line signal		in/out
		0	no End-of-dial line signal
		1	with End-of-dial line signal (EOD_free and EOD_busy)
P5	1	guard time before new outgoing seizure in seconds		in/out
		0	500 msec
		1-255	multiplied with 1 sec.
P6	0	dial tone recognition		out
		0	no dial tone recognition
		1	dial tone recognition
P7	0	answer supervision in case of outgoing directed traffic		out
		0	no answer supervision
		1-255	answer supervision in seconds
P8	0	blocking as line signal, if bothway or incoming directed traffic		in
		0	without blocking as line signal
		1	with blocking as line signal
P9	0	forward release after EOD-busy (valid only when P4=1)		out
		0	without forward release
		1	with forward release
P10	0	reserve
P11	0	reserve
P12	0	dialing method		in/out
		0	MF-Dial (multifrequency)
		1	DP-Dial (dial pulse)
P13	5	reanswer supervision time on outgoing traffic		out
		0	immediate forward release to the line after clear back
		1-254	delayed forward release to the line after clear back (... x 1s)
		255	endless (no forward release to the line after clear back, waiting for release from DH)
P14	40	supervision time for release forward after clear back on incoming traffic		in
		0	endless forward release supervision
		1-255	alarm to DH after supervision time (... x 1s)

Longtimer	Default (ms)	Description	Remark
L1	700	release gap to tie (outgoing) (300- 1000 ms)
L2	150	release gap minimum from tie (incoming) (50- 300 ms)
L3	1000	blocking against new seizure (500- 5000 ms)
L4	120	time between reversals by start of dial in time (100- 300 ms)
L5	4000	time for recognition of line alarm by line supervision (2000- 6000 ms)
L6	4000	waiting time for release acknowledge from tie (incoming) (2000- 6000 ms)
L7	0	reserve

Shorttimer	Default (ms)	Description	Remark
S1	120	remote blocking pulse (outgoing) (80-255 ms)	only if P1=1.
S2	40	minimal time for seizure recognition (20- 40 ms)	only if P1=0 or P1=2. (for P1=1 minimal time for seizure recognition is S7 + S8)
S3	60	minimal time after outgoing seizure untill current recognition (outgoing) (40-100 ms)	only if P1=0. (for P1=1 or 2: see S9)
S4	200	maximal time for start of dial in time (outgoing) (100-250 ms)
S5	40	minimal time for recognition of a line interruption (incoming) (10-80 ms)
S6	20	time between potential-recognition and acknowledge to DH (outgoing) (10- 250 ms)	for P1=1 do S6=150m, for P1=0 or P1=2 do S6=20ms.
S7	110	remote blocking pulse minimum (incoming) (80- 200 ms)
S8	40	remote blocking pulse tolerance (incoming) (10- 60 ms)
S9	100	maximal time after outgoing seizure until current recognition (outgoing) (50- 200 ms)	only if P1=1 or P1=2. (for P1=0 see S3)
S10	20	dialing pulse minimum (incoming) (10- 30 ms)
S11	20	dialing pause minimum (incoming) (10- 30 ms)
S12	20	recogniton of a saved potential after line alarm (incoming) (10- 50 ms)
S13	0	reserve
S14	130	interdigit time minimum (incoming) (100- 200 ms)

Parameter	Default	Description		Remark
P1	0	operating mode
		0	feeding with line supervision
		1	feeding with remote blocking
		2	loop without line supervision and remote blokkingrt	P2=1 only if P1=1
P2	0	send remote blocking (only valid if p1=1)
		0	without blocking signal
		1	with blocking signal
P3	0	start of dial signal
		0	without start of dial signal
		1	with start of dial signal in time (L4, S4)	P3=1 only if P1=0 or P1=1
		2	with continuous start of dial signal	P3=2 only if P1=0 or P1=1
P4	2	end of dial and answer
		0	without end of dial, without answer
		1	with end of dial, without answer	P4=1 only if P1=0 or P1=1
		2	without end of dial, with answer	P4=2 only if P1=0 or P1=1
		3	with end of dial, with answer	P4=3 only if P1=0 or P1=1
P5	0	automatic end of dial signal (only valid if p1=0 or 1)
		0	without
		n	no. of digits till automatic end of dial (n=1...20)	P5=1 only if P4=1 or P4=3
P6	0	seizure acknowledge
		0	acknowledge with BEL_QUITTUNG (a dialtone receiver will be connected, digits will be send from DH after a valid dialtone)	P6=0 only if P3=0
		1	acknowledge with WAHLABRUF (digits will be send from DH immediately)
P7	1	alarm in case of release supervision:
		0	with alarm by release supervision (L6)	P7=0 only if P1=1 and P8=1
		1	without alarm
		2	ignore release from tie line	P7=2 only for test
P8	0	backward release transmission after answer (incoming):
		0	with feeding gap	P8=0 only if P1=0 or P1=1.
		1	with reversal	P8=1 only if P1=0 or P1=1
P9	0	backward release recognition after answer (outgoing):
		0	ignore reversal after answer	P9=0 only if P1=0 or P1=1
		1	interpret reversal after answer as release	P9=1 only if P1=0 or P1=1.
P10	0	change of level by message PEGEL_SCHALTEN:
		0	no change of level
		1	change of level possible
P11	0	reserve
P12	0	reserve
P13	0	reserve
P14	0	reserve

Longtimer	Default (ms)	Description	Remark
L1	300	max recognition time for answer (300-3000 ms)
L2	0	reserve
L3	0	reserve
L4	0	reserve
L5	0	reserve
L6	0	reserve
L7	0	reserve

Shorttimer	Default (ms)	Description	Remark
S1	100	verification of line signal end (20-200 ms)
S2	0	reserve
S3	0	reserve
S4	0	reserve
S5	0	reserve
S6	0	reserve
S7	0	reserve
S8	0	send level for 2 VF fwd / bwd release signal 0 send level is equal 1 VF signals 1 send level is higher than 1VF signals
S9	0	send level for 2 VF out of service signal 0 send level is equal 1 VF signals 1 send level is higher than 1VF signals	if P4=3 or 4
S10	0	incoming seizures during line supervision alarm	if P12=1
		0 no incoming seizure is accepted
		1 - inc. dispatcher seizures accepted at once - inc. normal seizures are not accepted
		2 - inc. dispatcher seizures accepted at once - inc. normal seizures accepted as 3rd f1 test pulse
S11	0	LTG-alarm printout
		0 only one LTG_ALARM type	HICOM version <V1.0 (ZEITUEBERLAUF_4 to DH)
		1 different LTG_ALARM types	HICOM version >= V1.0 (SPERREN to DH)
S12	0	reserve
S13	0	reserve
S14	0	reserve

Parameter	Default	Description		Remark
P1	1	send level for VF signals
		0	high =0 dBm0 (FW1) / low =-8,8 dBm0 (FW2)
		1	standard=-4,4 dBm0 (FW1 + FW2)
P2	0	restriction of normal calls by dispatcher dialling		for time limit refer to P9
		0	no dailling by dispatcher possible
		1	restrict normal calls by dispatcher dialling	digit to be dialed by dispatscher corresponds the value of P3
		2	restrict normal calls by dispatcher dialling and transmit digit to remote switch (only outgoing traffic)
P3	0	restriction of normal calls by initialisation		for time limit refer to P9
		0	no restriction
		1	restriction of outgoing + incoming normal calls
		2	restriction of outgoing normal calls
		3	restriction of incoming normal calls
P4	0	blocking transmission
		0	no blocking
		1	blocking with 1200Hz
		2	blocking with 1600Hz
		3	blocking with 1200/1600Hz
		4	alternating blocking cycles for line frequency test	for timing refer to P10/P11
P5	0	speech path through connection befor answer
		0	one way through connection
		1	both way through connection
P6	0	post dialling
		0	no post dialling
		1	post dialling
P7	4	answer supervision in outgoing traffic
		0	no answer supervision
		1-60	answer supervision time in 30 sec. steps
P8	0	change of level attenuation
		0	no change of level attenuation
		1	change of level attenuation possible
P9	12	time limit for restriction of normal calls		refer to P3
		0	no time limit for restriction
		1-255	time limit for restriction of normal calls in 10 min. steps
P10	4	transmission time of frequency in line test		only if P4=4
		0	10s test tone on
		1-100	transmission time in multiples of 10s
P11	1	pause time between frequencies in line test		only if P4=4
		0	10s test tone off
		1-100	pause time in multiples of 10s
P12	0	line supervision in idle
		0	no line supervision
		1	with line supervision
P13	0	suppression of received line signals
		0	during transmission received line signals are accepted
		1	during transmission received line signals are suppressed
P14	4	answer supervision for incoming traffic
		0	no answer supervision
		1-60	answer supervision time in multiples of 30s