196.8 Parameter Description


AKTPOS	Used in command: SELMSG;
	specifies the position of the byte in current message (setting conditionals conditions)
	Type of Input	:	single value, mandatory
	Possible Values	:	0 - 12000

ANS	Used in command: COPY, ON;
	specifies if copy is to continue
	Type of Input	:	Single value, mandatory
	Possible Values	:	Y N	Yes No

ARCHIV	Used in command AUTOTR, FLAGTR define the file name of the backup file
	Type of Input	:	Single value, mandatory
	Possible Value	:	valid file name (e.g. ":PAS:TEST" or ":DBD:TEST")

AREA	Used in command: COPY; areas for which the command is valid
	Type of Input	:	single Value, mandatory
	Possible Values		STDTR	StandardTracer buffer
			FLAGTR	FlagTracer buffer
			AUTOTR	AutoTracer buffer
			RDSTR	RDSTracer buffer
			TAB-HD	save selection table
			HD-TAB	read selection table

AUTOTR	Used in command: AUTOTR;
	type of autotracer selection
	Type of Input	:	Single value, mandatory
	Possible Values	:	FILE	save file under different name
			OFF	block or deactivate or delete trace-criteria
			ON	activate a tracer function

BITPOS	Used in command: SELMSG;
	Bit positions which may be used for building a byte mask for mask comparison
	Type of Input	:	Single value, mandatory or linked Single values and/or range entries, mandatory
	Possible Values	:	BIT1	Setting the 1. bit of a byte
			BIT2	Setting the 2. bit of a byte
			BIT3	Setting the 3. bit of a byte
			BIT4	Setting the 4. bit of a byte
			BIT5	Setting the 5. bit of a byte
			BIT6	Setting the 6. bit of a byte
			BIT7	Setting the 7. bit of a byte
			BIT8	Setting the 8. bit of a byte

BLOCKNO	Used in command: DN, DN-T; specifies the block number on the harddisk
	Type of Input	:	Single value, mandatory
	Possible Values	:	1 - 65535

CCT	Used in command: SELDYN and FLAGTR, RDSTR;
	circuit number (=CirCuiT)
	Type of Input	:	Single value, mandatory
	Possible Values	:	0 - 255

CMD	Branch parameter,
	specifies the tracer command
	Type of Input	:	Single value, mandatory
	Possible Values	:	OFF, USER, DA, DB, DF, DL, DA-T, DB-T, DF-T, DL-T, DISPLAY,DN, DN-T, ON, COPY, END, MAXNO, MSGLEN, P, RES, RST, SELDYN, FLAGTR, NETSTOP, SELMSG, SELSTOP, SETLAN, STA

			(for explanation see Functional Overview)

CNT	Used in commands: DA, DB, DF, DL; DA-T, DB-T, DF-T, DL-T;
	specifies number of trace objects to be output
	Type of Input	:	Single value, optional
	Possible Values	:	1 - 65535
	Default Value	:	10

COND	Used in commands: SELMSG, SELDYN;
	branch parameter, specifies which condition is set.
	Type of Input	:	Single value, optional in SELMSG
		:	Single value, mandatory in SELDYN
	Possible Values	:	ALL	Select all messages (SELMSG only)
			OFF	Deactivate message selection for a group
				or deactivate selection at gate trace points
			CD1	1st condition
			CD2	2nd condition
			CD3	3rd condition
			CD4	4th condition
			CD5	5th condition
			CD6	6th condition
			CD7	7th condition
			CD8	8th condition
			CCD1	1st conditional condition (SELMSG only)
			CCD2	2nd conditional condition (SELMSG only)
			CCD3	3rd conditional condition (SELMSG only)
			CCD4	4th conditional condition (SELMSG only)
			CCD5	5th conditional condition (SELMSG only)
			CCD6	6th conditional condition (SELMSG only)
			CCD7	7th conditional condition (SELMSG only)
			CCD8	8th conditional condition (SELMSG only)
	Default Value	:	OFF

CONDGRP	Used in commands: MSGLEN, SELDYN, SELMSG, SETLAN;
	specifies group for which conditions are to be set
	Type of Input	:	Single value, optional (SELDYN, SELMSG)
		:	Single value, mandatory (MSGLEN, SETLAN)
	Possible Values	:	For MSGLEN, SETLAN:
			G1	Condition group 1
			G2	Condition group 2
			G3	Condition group 3
			G4	Condition group 4
			For SELDYN, SELMSG:
			G1	Condition group 1
			G2	Condition group 2
			G3	Condition group 3
			G4	Condition group 4
			OFF	Deactivate message selection at a trace point
	Default Value	:	OFF

CONVERT	Used in commands: SELMSG;
	conversion of switching values
	Type of Input	:	Single value, 2 linked Single values, optional
	Possible Values	:	DTI	device table index
			LINE	line number
			LODAD	logical device address
			LODADP	lodad packed
			LODEN	logical device number
			LTGLINE	ltg line

CPCOND	Used in command: SELDYN;
	indicates whether dynamic memories are also entered in the trace
	buffer for a selected SW message or a CALL gate.
	Type of Input	:	Single value, linked Single values optional
	Possible Values	:	ALL	select all dynamic memories
			OFF	deactivate memory selection
			CPB	DB_D_CPB_TBL
			CPCRF	DB_D_CP_NW_CR_TBL
			DCLD	DB_D_CP_LOGICAL_DEV_TBL
				additionally, depending on device type:
				DB_D_CP_DD_EXT_G_ATND
				DB_D_CP_DEV_TBL_EXT_ATND
				DB_D_TM_M_ATND_TIME_I_SERV
				DB_D_CP_DEV_TBL_TRUNK
			DCLT	DB_D_TLN_DATA_TBL or DB_D_TRUNK_DATA_TBL
			DDHD	DB_D_DH_DEV_TBL
			DHCRF	DB_D_DH_NW_CR_TBL
	Default Value	:	OFF

CPPNT	Used in command: SELDYN;
	specifies the trace point at a call processing trace interface or the GATE trace point for
	which a dynamic memory is to be output (message-dependent address for SW trace points,
	explicit for GATEs)
	Type of Input	:	Single value, mandatory
	Possible Values	:	CP	call processing
			FLAGTR	CP and PP messages with set flag
			PP	peripheral processing
			SW	CP and PP
			START	start condition
			GATE	gate trace point
			AUTOTR	CP and PP of AutoTracer

DI	Used in command: SELDYN, FLAGTR and RDSTR;
	device indicator
	Type of Input	:	Single value, optional
	Possible Values	:	0 - 255

DISPLACE	Used in commands: DA, DB, DF, DL, DN, DA-T, DB-T, DF-T, DL-T, DN-T, SELMSG;
	indicates the displacement of the byte in the trace object which is to be compared
	with the values of parameter VAL
	Type of Input	:	Single value,
			mandatory in SELMSG
			optional in DA, DB, DF, DL, DN, DA-T, DB-T, DF-T, DL-T, DN-T
	Possible Values	:	For DA, DB, DF, DL, DN, DA-T, DB-T, DF-T, DL-T, DN-T
			and SELMSG with FLDTYPE = BYTE, PST:
			0 - 12000
			For SELMSG with FLDTYPE = SDNO:
			0 - 1

FILE	Used in command: COPY, DISPLAY, ON, RDSTR; defines the file name of a file for storing the trace buffer on hard disk.
	Type of Input	:	Single value, mandatory
	Possible Values	:	valid file name (e.g. ":PAS:TEST" or ":DBD:TEST")

FLDTYPE	Used in command: SELMSG;
	branch parameter, specifies the field in the trace
	object on the basis of which selection is to be made.
	Type of Input	:	Single value, mandatory
	Possible Values	:	BYTE	next defined byte
			DEST	destination task
			EV	event code
			PST	powerset resp. mask comparison
			SRC	source task
			SEVT	subevent code
			SU	subunit
			SDNO	status diagram number

FILETYPE	Used in command: DISPLAY; defined from which tracer type the file is displayed
	Type of Input	:	Single value, mandatory
	Possible Value	:	STDTR	StandardTracer file
			FLAGTR	FlagTracer file
			AUTOTR	AutoTracer file
			RDSTR	RDSTracer file
			OFF	Stop read from file
			FILE	User defined file name
			*	synonym for the file name of StandardTracer

FLAGTR	Used in command: FLAGTR
	type of flagtrace selection
	Type of Input	:	Single value, mandatory
	Possible Values	:	ADD	add tracing flag for a line or add selection value
			DEL	remove tracing flag or dyn. deleting of values
			FILE	save file under different name
			OFF	block or deactivate or delete trace-criteria
			ON	activate a tracer function
			STOPALL	stop systemwide or stop of flag tracing at stopall

INFO	Used in command: STA
	indicates how much or form wich trace type information is output
	Type of Input	:	Single value, optional
	Possible Values	:	S	short information of StandardTracer
			L	long information of StandardTracer
			M	medium information of StandardTracer
			C	selection conditions of the StandardTracer
			HD	Tracefile info of the StandardTracer
			STDTR	long information of StandardTracer
			FLAGTR	long information of FlagTracer
			AUTOTR	long information of AutoTracer
			RDSTR	long information of RDSTracer
			ALL	information of all tracer types
	Default Value	:	S

LEN	Used in commands: DA, DB, DF, DL, DN, DA-T, DB-T, DF-T, DL-T, DN-T, MSGLEN;
	For DA, DB, DF, DL, DN, DA-T, DB-T, DF-T, DL-T, DN-T:
	Maximum output length of a trace object in bytes
	For MSGLEN:
	Maximum entry length for a message
	The supplementary data, e.g. SDNO, etc., is not included.
	Type of Input	:	Single value, optional
	Possible Values	:	0 - 65535
			(may be reduced by the AMO to the maximum value implemented)
	Default Values	:	For DA, DB, DF, DL, DN, DA-T, DB-T, DF-T, DL-T, DN-T:
			None (full object length is default value)
			For MSGLEN:
			16

LN	Used in command: SELDYN, FLAGTR and RDSTR;
	Specifies the line number
	Type of Input	:	Single value, in FLAGTR also range entries, mandatory
	Possible Values	:	1 - 65535

LOCK	Used in command: SELMSG;
	Specifies the lock of dynamic manipulations of conditions
	Type of Input	:	Single value, optional
	Possible Values	:	BLOCK	blocking execution of conditional conditions
			UNBLO	unblocking execution of conditional conditions

LTU	Used in command: SELDYN, FLAGTR and RDSTR;
	Specifies the LTU number
	Type of Input	:	Single value, mandatory
	Possible Values	:	1 - 15 and 17 - 99

MAXBLOCK	Used in command: AUTOTR, FLAGTR, RDSTR, ON;
	Specifies the filesize in multiple of trace buffer.
	Type of Input	:	Single value, optional
	Possible Values	:	For AUTOTR, FLAGTR
			10 - 99
	Default Value	:	20
	Possible Values	:	For ON
			1 - 2000
	Default Value	:	10
	Possible Values	:	For RDSTR, ON
			1 - 99
	Default Value	:	10

MAXNO	Used in command: MAXNO;
	Specifies the maximum number of trace objects to be written into the buffer.
	Type of Input	:	Single value, optional
	Possible Values	:	0 to 65535
	Default Value	:	0 (= unlimited)

NETPROT	Used in command: NETSTOP;
	branch parameter, specifies the type of netprotocol of switch networking.
	Type of Input	:	Single value, mandatory
	Possible Values	:	CORNET	switch connected via CORNET-N

NO	Used in command: DN;
	the objects in the trace buffer are consecutively numbered from 1 to 65535 (0 is 65536).
	This consecutive number can be used to specifically address each trace object.
	Type of Input	:	Single value, linked Single values, mandatory
	Possible Values	:	0 - 65535

NODEACC	Used in command: NETSTOP
	Node access of target hicom
	Type of input		Single value, optiona
	Possible Values		0 -65535

NUMCD	Used in command: SELMSG;
	Specifies the NUMber of ConDitions which are dynamic to change.
	Type of Input	:	Single value, optional
	Possible Values	:	1 - 8
	Default Value	:	1

OVERWRT	Used in command: ON, RDSTR;
	Specifies whether a file is overwritten or not
	Type of Input		Single value, optional
	Possible Values		Y	File will be overwritten
			N	File will be not overwritten

PHYSEL	Used in command: SELDYN;
	physical selector of the call gate in the GDT.
	Type of Input	:	Single value, mandatory
	Possible Values	:	0 - FFFF

POOLSIZE	Used in command: ON, RDSTR; specifies the number of trace buffers in the trace buffer pool
	Type of Input	:	Single value, optional
	Possible Value	:	0 (no trace buffer pool)
			7 - 99
	Default Value	:	20

RESOBJ	Used in command: RES;
	parts of the tracer that are reset.
	Type of Input	:	Single value, optional
	Possible Values	:	BUF	Trace buffer of the StandardTracer, i.e. the buffer contents are deleted.
			TBL	All selection tables, i.e.:
				No message is selected.
				No dynamic memory addressed by a message
				is selected.
				No control condition is set.
				All the length fields are set to 16 bytes.
				(The condition bits for post-selection
				remain unchanged).
			GATE	Gate trace point.
				No dynamic memory is selected at gate.
			STDTR	The trace buffer and all selection tables of the StandardTracer are reset. StandardTracer is switched off.
			ALL	Like STDTR: The trace buffer and all selection tables of StandardTracer are reset.
			FLAGTR	The trace buffers of FlagTracer are reset; Selection table is reset to default. FlagTracer is switched on.
			AUTOTR	Selection table of AutoTracer is reseted to default, AutoTracer is switched on.
			RDSTR	The trace buffer and all selection tables of the RDSTracer are reset. RDSTracer is switched off.
			TRPOOL	Release the trace buffer pool. The buffers of the resident tracer are not affected.
	Default Value	:	BUF

SELADR	Used in command: SELDYN, FLAGTR and RDSTR;
	Specifies the type of address of dynamic memory at call gate.
	Type of Input	:	Single value, mandatory
	Possible Values	:	CIR	Circuit address
			LN	Line address
			STNO	Input of station number (only in FLAGTR)

SELLINE	Used in command: NETSTOP;
	Specifies the selection of the CORNET - Line (switch networking).
	Type of Input	:	Single value, mandatory
	Possible Values	:	OFF	delete all NETSTOP conditions
			L1	Line of 1st partner switch
			L2	Line of 2nd partner switch
			L3	Line of 3rd partner switch
			L4	Line of 4th partner switch
			L5	Line of 5th partner switch
			L6	Line of 6th partner switch
			L7	Line of 7th partner switch
			L8	Line of 8th partner switch

SLOT	Used in command: SELDYN, FLAGTR and RDSTR;
	Specifies the slot number
	Type of Input	:	Single value, mandatory
	Possible Values	:	1 - 121
A suitable module must be configured for the slot addressed by PEN (AMO BCSU).
The possible Slot values depend on the systems architecture and can be found in the BCSU AMO description.

STNO	Used in command: FLAGTR, RDSTR
	specifies the station number
	Type of Input:		Single value, mandatory
	Possible values:		Letter A-D, digit, "#" and "*"

STYPE	Used in commands: ON, RST, SELMSG, SELSTOP;
	specifies how the criterion for restart stability (RST)
	and/or the serialization mechanism is to be set (SELSTOP)
	and/or what action is to execute (SELMSG)
	and/or if the trace result is also to store on harddisk (ON)
	Type of Input	:	Single value, optional in ON Single value, mandatory in RST, SELMSG, SELSTOP
	Possible Values	:	For ON:
			BUF	Tracing only in trace buffer (Default Value)
			HD	the full trace buffer is to store in a file on HD
			For RST:
			OFF	Tracer is not to have restart stability
			ON	Tracer is to have restart stability
			For SELMSG:
			ADD	adding of a selection value
			DEL	deleting of selection values of a condition
			SET	setting of a selection value
			SUB	deleting of a selection value
			For SELSTOP:
			OS	Serialization with OS resources
			LOCK	Serialization with interrupt disable

SU	Used in command: SELDYN, FLAGTR, RDSTR;
	specifies the sub-unit
	Type of Input	:	Single value, optional
	Possible Values	:	0 - 16
	Default Value	:	0

SVC	Used in command		FLAGTR, RDSTR;
	specifies the service identifier (SerViCe)
	Type of Input:		Single Value, mandatory
	Possible Values	:	VTX	videotext
			DTE	data
			FAX	fax
			TTX	teletext
			VCE	voice

TARGETCD	Used in commands: SELMSG;
	indicates weather dynamic condition is to be set
	Type of Input	:	Single value, optional
	Possible Values	:	CD1	first condition
			CD2	second condition
			CD3	third condition
			CD4	fourth condition
			CD5	fifth condition
			CD6	sixth condition
			CD7	seventh condition
			CD8	eighth condition
	Default Value	:	Value of the parameter COND

TARGETGRP	Used in commands: SELMSG;
	indicates for what group a dynamic condition is to be set
	Type of Input	:	Single value, optional
	Possible Values	:	G1	condition group 1
			G2	condition group 2
			G3	condition group 3
			G4	condition group 4
	Default Value	:	Value of the parameter CONDGRP

TARGETPO	Used in commands: SELMSG;
	indicates the byte position in the target message (for setting conditional conditions)
	Type of Input	:	Single value, mandatory
	Possible Values	:	0 - 12000

TARGETTP	Used in commands: SELMSG;
	indicates the target trace point for conditionals conditions
	Type of Input	:	Single value, optional
	Possible Values	:	AUTOTR	automatic restart tracer
		:	CP	call processing in switching software module
			FLAGTR	CP and PP messages with set flag
			LAN	LAN data
			PP	preprocessing in switching software module
			PT	stop condition for periphal lw tracer
			RCV	tracepoint in OS_RECEIVE_message
			SD	tracepoint in OS_SEND_ message
			RDSISDN	isdn messages of pp of set monitors
			RDSMON	cp and pp messages of the set monitors
			START	start condition for tracer
			STOP	stop condition for tracer
			STOPALL	stop condition for all tracer in system

	Default Value	:	Value of the parameter TRACEPT

TEST	Used in commands: DA, DB, DF, DL, DN, DA-T, DB-T, DF-T, DL-T, DN-T, SELMSG;
	specifies how the value is to be tested in
	pre- or post-selection (comparison TEST).
	Type of Input	:	Single value, optional
	Possible Values	:	Commands DA, DB, DF, DL, DN, DA-T, DB-T, DF-T, DL-T, DN-T:
			E	equal
			NE	not equal
			SELMSG in accordance with the set condition bits
			(For SELMSG,BUF,..?)
			For SELMSG:
			E	equal
			NE	not equal
	Default Value	:	E

TEXT	Used in commands: USER;
	contains infotext assigned to other users of the tracer and/or a name of own switch for in the net stopped partner switch
	Type of Input	:	Single value, optional
	Possible Values	:	Text, max 70 chars (in USER)

TRACEPT	Used in commands: MSGLEN, SELMSG;
	Specifies the trace point or the control condition
	at which a select criterion is to be set for messages.
	Type of Input	:	Single value, mandatory
	Possible Values	:	AUTOTR	CP and PP of AutoTracer
			BUF	Buffer; setting of condition bits for post-selection (only SELMSG)
			CP	Call processing
			FLAGTR	CP and PP messages with set flag
			OS	SD and RCV
			LAN	LAN trace point
			PP	Peripheral processing
			PT	PETRA Stop condition
			RCV	RECEIVE_MESSAGE in OS
			RDSMON	CP and PP messages of set monitors
			RDSISDN	ISDN messages of PP of set monitors
			SD	SEND_MESSAGE in OS
			SW	CP and PP
			START	Start condition
			STOP	Stop condition
			STOPALL	Stopall condition
			TIME	(dummy)

TYPE	Used in commands: DA, DB, DF, DL, DN, DA-T, DB-T, DF-T, DL-T, DN-T, SETLAN;
	For DA, DB, DF, DL, DN, DA-T, DB-T, DF-T, DL-T, DN-T:
	specifies which type of trace objects is to be output
	For SETLAN:
	specifies which type of LAN objects is to be traced
	Type of Input	:	Single value, for SETLAN mandatory, else optional
	Possible Values	:	For SETLAN:
			ETHRV	Ethernet driver: protocol headers of incoming frames
			ETHSD	Ethernet driver: protocol headers of outgoing frames
			IPDSD	IP data: dual-port-ram send
			IPDRV	IP data: dual-port-ram receive
			TCP	TCP data (Transmission Control Protocol)
			TPI	TPI data
			For DA, DB, DF, DL, DN, DA-T, DB-T, DF-T, DL-T, DN-T:
			ALL	all objects
			AUTOTR	CP and PP messages of AutoTracer
			AUTOC	like AUTOTR, additional SD-information
			CP	all messages from trace point CP
			CPC	like CP, additional SD-information
			CPB	DB_D_CPB_TBL
			CPCRF	DB_D_CP_NW_CR_TBL
			DCLD	DB_D_CP_LOGICAL_DEV_TBL
				additionally, depending on device type:
				DB_D_CP_DD_EXT_G_ATND
				DB_D_CP_DEV_TBL_EXT_ATND
				DB_D_TM_M_ATND_TIME_I_SERV
				DB_D_CP_DEV_TBL_TRUNK
			DCLT	DB_D_TLN_DATA_TBL or DB_D_TRUNK_DATA_TBL
			DDHD	DB_D_DH_DEV_TBL
			DHCRF	DB_D_DH_NW_CR_TBL
			ETHRV	Ethernet driver: protocol headers of incoming frames
			ETHSD	Ethernet driver: protocol headers of outgoing frames
			FLAGC	CP and PP messages with ZD-Infos
			FLAGTR	CP and PP messages with set flag
			IPDSD	IP data: dual-port-ram send
			IPDRV	IP data: dual-port-ram receive
			LAN	all LAN objects: ETHRV, ETHSD, TCP, TPI
			MSG	OS and SW
			OS	SD and RCV
			PP	all messages from trace point PP
			PT	message, which stopped PETRA
			PPC	like PP, additional SD-information
			RCV	all messages from trace point RCV
			RDS	RDSMON and RDSISDN, and additional all suplementary data
			RDSMON	CP and PP messages of set monitors
			RDSISDN	ISDN messages of PP of set monitors
			SD	all messages from trace point SD
			SW	CP and PP
			SWC	like SW, additional SD-information
			TCP	TCP data (Transmission Control Protocol)
			TPI	TPI data
	Default Value	:	MSG

UNIT	Used in commands: P and RDSTR;
	Type of Input	:	Single value, mandatory
	Possible Values	:	For P:
			BP	Base processor active
			BPA	Base processor A
			BPB	Base processor B
			BPS	Base processor stand by
			For RDSTR:
			1-4	prime monitor index
			ALL	all prime monitors

VAL	Used in commands: DA, DB, DF, DL, DN, DA-T, DB-T, DF-T, DL-T, DN-T, SELMSG;
	values with which the specified field is compared for selection.
	Linked Single values are treated as ’or’ strings.
	Type of Input	:	Single value,
			linked Single values and/or range entries
			mandatory in SELMSG
			optional in DA, DB, DF, DL, DN, DA-T, DB-T, DF-T, DL-T, DN-T
	Possible Values	:	hex values 00 - FF.

WRAP	Used in commands: ON, RDSTR;
	indicates whether the trace file is to be wrap around
	Type of Input	:	Single value, optional
	Possible Values	:	Y	wrap around the file
			N	if file is full trace data are written only in the TB
	Default		Y

OpenScape 4000 V10, Volume 1: AMO Descriptions, Service Documentation, Issue 5, ID: P31003H31A0S107057620

© 09/2025 Mitel Networks Corporation. - All rights reserved.
Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG. All other trademarks herein are the property of their respective owners.