199.4
Parameter Description
BCHAN1
B CHANNEL 1 (only for JITTERLP )
Type of Input
:
Single Value, optional
Possible Values
:
1 to 30 or 255 (loop over all b channels)
Default Value
:
255
BCHAN2
B CHANNEL 2 (only for JITTERLP)
Type of Input
:
Single Value, optional
Possible Values
:
1 to 30
Default Value
:
2
CCT
Circuit/trunk number
Type of Input
:
Single value, mandatory
Possible Values
:
0 to 255
(UNIT=CCT / CCTPATH / T / LINE)
0 to 3
(UNIT=JITTERLP)
HALF
Identifier for processor half
Type of Input
:
Single value, optional
Possible Values
:
ACT
= active system half
SBY
= standby system half
PARTA
= system half A
PARTB
= system half B
Default Value
:
ACT
HWY
Highway
Type of Input
:
Single value, optional
Possible Values
:
0 to 127
Default Value
:
(is defined by RTO)
LOOPBACK
Type of loopback (test loop number)
Type of Input
:
Single value, optional
Possible Values
:
2
only for PNT or NT (UNIT=T)
:
4
only for Cornet-T devices (UNIT=T)
SLMRV
only for Board SLMR (VOICE)
SLMRD
only for Board SLMR (DATA)
SMIDIG
only for LTUR SM Boards (DIGITAL)
SMIANA
only for LTUR SM Boards (ANALOG)
ILOC
internal local LB (TMD24, T1DN)
IDC
activate int. remote LB (TMD24, T1DN)
IDL
deactivate int. rem. LB (TMD24,T1,TMDN)
EDC
external remote LB (TMD24, T1,TMDN)
RLITDM
data channel LB (RLI)
IPON
payload loopback on (TMDN)
IPOFF
payload loopback off (TMDN)
ONHOOK
test loop for a subscriber in state ’onhook’(line test on SLMA)
OFFHOOK
test loop for a subscriber in state ’offhook’(line test on SLMA)
Default Value
:
look at list of possible test loops
LTG
Line/trunk group
Type of Input
:
Single value, mandatory
Possible Values
:
1 bis 32
LTU
Line/trunk unit
Type of Input
:
Single value, mandatory
optional (UNIT=LTU)
Possible Values
:
1 to 99
Default Value
:
1
OBJECT
Choice between test of one terminal or test of all terminals of a circuit
Type of Input
:
Single value, mandatory
Possible Values
:
SINGLE (Test of a single terminal)
ALL (Test of all terminals of circuit using loop 4)
PCMLINE
PCM line number
Type of Input
:
Single value, optional
Possible Values
:
1 to 4
Default Value
:
1
SERVICE
Specify the type of service of the terminal to be tested
Type of Input
:
Single value, optional for Workstations
:
Single value, mandatory
Possible Values
:
DTE, FAX, VCE
SLOT
Slot number in the LTU
Slots are numbered from left to right. Always state the lowest slot number for modules
which occupy more than one location. (A mounting location is made up of 6 slots ;
thus, valid slot numbers are 1, 7, 13, 19 etc.
However: some modules - e.g. SLMA - occupy two locations; for this reason the valid
slot number must always be the first, or lowest, of the two. LTUC cannot be tested!)
Type of Input
:
Single value, mandatory
Possible Values
:
1 - 121 (non compact hardware)
:
19 - 121 (compact hardware)
A suitable module must be configured for the slot addressed by PEN (AMO
BCSU
).
The possible Slot values depend on the systems architecture and can be found in the BCSU AMO description.
STNO
Station number of terminal to be tested
Type of Input
:
Single value, mandatory
Possible Values
:
0 - 999999
TESTTYPE
Type of terminal test (parameter exists only in Hicom 300 V3.4)
Type of Input
:
Single value, mandatory
:
Possible Values
SELFTEST
LOOPBACK
CHKALIV
LINEPOW
TSI
Terminal selection identifier
Type of Input
:
Single value, optional
Possible Values
:
1 - 8
Default Value
:
LOOPBACK
=4 : all devices of a S0-bus or
a hole Workstation or
LOOPBACK
=2 : PNT or NT
TSL
Timeslot
Type of Input
:
Single value, optional
Possible Values
:
0 to 31
Default Value
:
1
TYPE
Type of definiton of terminal to be tested
Type of Input
:
Single value, mandatory
:
Possible Values
PEN
= Port equipment number
STNO
= Station number
UNIT
System unit to be tested
Type of Input
:
Single value, mandatory
Possible Values
:
LTG
= Line trunk group
CC
= Common control
CLTG
= Central parts of LTG
LTU
= Line trunk unit
BRDHWY
=Board highway of LTUC
MDL
= Module (in an LTU shelf)
CCT
= Circuit
CCTPATH
= Circuit using defined hwy and tsl
SIU
= Signaling unit (Standard)
CONF
= Conference board
SPHW
= Speech highway
T
= Terminal
PCMLINE
= PCM line
JITTERLP
= Special loop on DIUS2, DIUS7, SLMN-E1
(only for jitter measurements)
CONWADP
= Connection betw WAML board and ADP
LINE
= Line testing on SLMA boards
SURVMOD
=IPDA survivability modem
SURVPATH
=IPDA survivability path
CBMM
=Central byte manipulation module
OpenScape 4000 V10, Volume 1: AMO Descriptions, Service Documentation, Issue 5
, ID:
P31003H31A0S107057620
©
09/2025
Mitel Networks Corporation. - All rights reserved.
Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG. All other trademarks herein are the property of their respective owners.