200.4 Appendix to the parameter description

Parameterdescription for WCU tables
Supplement of with the parameters TARMIN, TAR, TAR1, TAR2, TAR3, TAR4 possible values:
Output format
The calculated costs are displayed according to the settings added through the AMO-DAVF. Display settings are:
1.
Comma position: the position of the comma (-3 to 3 and 3T, 2T)
Examples:
 
Comma position: 3
Value: 30558
Output: 305,580
Comma position: 2
Value: 30558
Output: 305,58
Comma position: 1
Value: 30558
Output: 305,6
Comma position: 0
Value: 30558
Output: 306
Comma position: -1
Value: 30558
Output: 3056
Comma position: -2
Value: 30558
Output: 30558
Comma position: -3
Value: 30558
Output: 305580
Comma position: 2T (Rounded)
Value: 30558
Output: 30,56
Comma position: 3T
Value: 30558
Output: 30,558
2.
Currency identifier: Character string z.B: DEM, ATS, USD etc.
Parameterdescription for WOCU tables
Supplement of with the parameters TARBAS, TARMIN, TARDAY, NTAR1, NTAR2, NTAR3, NTAR4 possible values
Output format
The calculated costs are output according to the representation features adjustable by means of branch GEN (appropriately to the respective tariff tables)
1.
Comma position: the position of the comma (-3 to 3 and 3T, 2T)
Examples:
 
Comma position: 3
Value: 30558
Output: 305,580
Comma position: 2
Value: 30558
Output: 305,58
Comma position: 1
Value: 30558
Output: 305,6
Comma position: 0
Value: 30558
Output: 306
Comma position: -1
Value: 30558
Output: 3056
Comma position: -2
Value: 30558
Output: 30558
Comma position: -3
Value: 30558
Output: 30558
Comma position: 2T (Rounded)
Value: 30558
Output: 30,56
Comma position: 3T
Value: 30558
Output: 30,558
Comma position: 2HT (Rounded)
Value: 30558
Output: 0,31
Comma position: 3HT (Rounded)
Value: 30558
Output: 0,306
2.
Currency identifier: Character string z.B: DEM, ATS, USD etc.
Cost calculation
Cost calculation (with charge information) is performed in 1/100ths of currency units if AMO- DAVF COMPOS parameter’s value is 2T or 3T. The currency unit is the one unit with the indicated currency flags. This setting corresponds to comma position 2. For example the calculated amount is equal to 30558, which corresponds to the costs of 305,58 currency units.
If the comma position of AMO-DAVF is equal to 2T or 3T thus in 1/1000th currency units one counts. If the calculated costs amount to 30558, thus the display shows in case COMPOS=2HT the amount 30,56, in case 3HT the amount 30,558. This applies only, if the calculation takes place after the branch WCU of the AMO-TTBL.
The positive comma positions do not influence only the number of places which can be displayed after the comma, the value or amount however. From it results that all tariff specifications must be indicated in 1/100th currencies, if COMPOS is 0 to +3. If COMPOS is 2T or 3T then in 1/1000th.
For tariff values (TARMIN, TARIF1, etc.) the valid range is from 0000 to 9999.
Negative comma positions mean an output without comma position, with a shift of the comma by 1 to 3 positions to the right (this is equivalent to a division by 10 Comma position). This means that a comma position of -1 and a value of 30558 gives a cost of 305,58 / 10-1 = 3056, for comma position -2 a cost of 305,58 / 10-2 = 30558, etc.
With calculation after zone the comma position configures tariff tables-non standard. In the branch GEN the comma position administers similar to as by AMO-DAVF. If the comma position is equal to -3, -2, -1,0, +1, +2 oder +3, the cost calculation takes place in 1/100th currency units. At comma position equal to 2T or 3T the cost calculation takes place in 1/1000th currency units, at comma position 2HT or 3HT the cost calculation takes place in 1/100000th currency units.
The minimum tariff (TARMIN) and the basic tariff (TARBAS) become further 1/100th currency units.
Attention: The value of the comma position applies not only for the assigned tariff table! If there are different tariff table numbers used for the display output (tariff table 0) and the data record (tariff table from the selcection group) then a comma position is for both tariff tables to set.
Example 1:
A call charge unit costs 12,1 Pfennigs.
Input: TARIF = 0121 (00,121 DEM), comma position 3, currency identifier =’DEM’. The parameter COMPOS of AMO-TTBL ist 2T or 3T.
Example 2:
90 seconds connection time with day tariff costs 3,6 ATS.
Input: TARDAY = 0360 (03,60 ATS), INTDAY = 9000 (in 1/100ths of seconds), Comma position 1 or 2, Currency identifier = ’ATS’. The parameter COMPOS of AMO-TTBL is +2.
Example 3:
A call charge unit costs 812 Lire. We would have to enter parameter TAR = 81200 (812,00 Liras). But only 4 digits are allowed, so this is not permitted.
Solution: Add comma position -1, then TAR = 8120. That’s 81,20 Lire, but due to the negative comma position, the output is multiplied by 100.
Example 4:
A call charge unit costs 1350 Lire. We would have to enter parameter TAR = 135000 (1350,00 Lire).
Solution: Add comma position -2, then TAR = 1350. That’s 13,50 Lire, but due to the negative comma position, the output is multiplied by 100.
Example 5:
The tariff modell CITY-CALL costs 0,127 Pfennig per second (every daytime).
Input: INTDAY, INTNT1, INTNT2, INTNT3, INTNT4 = 100 (1 second), TARDAY, NTAR1, NTAR2, NTAR3, NTAR4 =127. The used tariff table 2HT or 3HT installes in the branch COMPOS (the calculation in 1/100000th currency units and output on display in 2 or 3 back comma positions)
OpenScape 4000 V10, Volume 1: AMO Descriptions, Service Documentation, Issue 5, ID: P31003H31A0S107057620
 © 09/2025 Mitel Networks Corporation. -  All rights reserved.
 Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG. All other trademarks herein are the property of their respective owners.