You can only release the feature in expert mode. Expert mode --> ComWin --> Open ...< IP> using AMO (see AMO command).

To use the AMO ZAND to release AUN:

CHANGE-FEASU:TYPE=A,CM=PU;

You can only set the mode in expert mode.

Expert mode --> ComWin --> Open ...< IP> using AMO (see AMO command).

If you want the press to call pickup key only once to pick up the call, you must set the PICKOPT parameter as follows:

CHANGE-ZAND:TYPE=OPTISET,PICKOPT=NO;

You can only configure a code (with * or #) for call pickup in expert mode. Expert mode --> ComWin --> Open ...< IP> using AMO (see AMO command).

To configure a code for call pickup using the AMO WABE:

You can only change the dimensioning data in expert mode. Expert mode --> ComWin --> Open ...< IP> using AMO (see AMO command).

Set the number of possible call pickup groups with the AMO DIMSU, parameter PUGR.

Configuration Management --> Groups --> Call Pickup, Extension tab, click New and then enter the number. To add more numbers, click Add (symbol at the right) and enter the other numbers in the new field. (You must repeat this step for each station number.)

Using default values with the AMO AUN:

ADD-AUN:STNO=<number>;

Configuration Management --> Groups --> Call Pickup, Extension tab, click New and then enter the number. To add more numbers, click Add (symbol at the right) and enter the other numbers in the new field. (You must repeat this step for each station number.) You can specify and save the separate parameters (such as alerting call) under the Suppl. Data tab.

Do not use the AMO AUN default values:

ADD-AUN:STNO=number[,DISTNO=YES][,NOTRNG=PERIOD1][,PUSECOND=YES][,SIGNAL=LED];

Configuration Management --> Groups --> Call Pickup, Extension tab, click New and then enter the number. To add more numbers, click Add (symbol at the right) and enter the other numbers in the new field. (You must repeat this step for each station number.) You can enter and then save the required group number (GRNO) for the call pickup group.

By entering the number with the AMO AUN:

ADD-AUN:GRNO=21,STNO=<number>;

You can only administer the move of station numbers from one pickup group to a new group in expert mode. Expert mode --> ComWin --> Open ...< IP> using AMO (see AMO command).

Using the AMO AUN to move them is the same as a normal configuration:

ADD-AUN:STNO=<number1&number2&number3>;

Configuration Management --> Groups --> Call Pickup, Extension tab, enter the station number of a member of the call pickup group and click Search. Click Add Entry (symbol at the right) and enter the new station number in the new field.

(You must repeat this step for each station number.)

Determine existing call pickup group by the group number and expand the group:

Or determine existing call pickup group by a user in the group:

ADD-AUN:GRSTNO=<number>,STNO=<number>;

Configuration Management --> Groups --> Call Pickup, Extension tab, enter the station number of a member of the call pickup group and click Search. You can change and save the separate parameters (such as alerting call) under the Suppl. Data tab.

Change with the AMO AUN:

CHANGE-AUN:TYPE=GR,GRNO=1,{[,DISTNO=YES][,NOTRNG=ONIDLE1][,PUSECOND=YES][,SIGNAL=NONE]};

You can only administer the time until the alerting call sounds in expert mode. Expert mode --> ComWin --> Open ...< IP> using AMO (see AMO command).

Change the parameter BURST using the AMO DTIM1:

CHANGE-DTIM1:TYPEDH=DIGITE,BURST=<sec>;

You can only administer the time for the alerting call in expert mode.

Expert mode --> ComWin --> Open ...< IP> using AMO (see AMO command).

Change the parameter NOTRNG using the AMO CTIME:

CHANGE-CTIME:TYPESWU=CPTIME1,NOTRNG=<sec>; (5 to 30 seconds)

Configuration Management --> Tables --> Class of Service, tab Voice 1, click parameter GRPCAL (checkmark appears) and save.

With AMO COSSU (class of service GRPCAL):

CHANGE-COSSU:TYPE=COS,COS=<number>,AVCE=GRPCAL;