14.4.11.4.4. 5-digt On-Base-Number Configuration Example 
The OpenScape 4000 uses the timer LCREOD to determine whether a 5
digit number is dialed. If there is no other digit dialed within this
timer (or if the user dials the pound "#') the OpenScape 4000 assumes
that all digits are dialed and routes them accordingly.
The timer LCREOD (LCR End Of Dialing) is used for dialing supervision
and can be changed with the AMO-CTIME (recommended value 4 seconds):
CHA-CTIME:TYPESWU=CP1,LCREOD=4;
The digits 2 through 8 have to be configured as a routing digit since 2 to 8 are possible
start digits for DSN numbers (see Section 174.1, "Interswitch and Intraswitch Dialing").
ADD-WABE:CD=2,DAR=TIE; ADD-WABE:CD=3,DAR=TIE; ADD-WABE:CD=4,DAR=TIE; ADD-WABE:CD=5,DAR=TIE; ADD-WABE:CD=6,DAR=TIE; ADD-WABE:CD=7,DAR=TIE; ADD-WABE:CD=8,DAR=TIE;
OpenScape 4000 internal stations need to be configured with a token number since the
"real"
station numbers are used to route the calls (in this example 1 is added to the on
base number
KXXXX):
ADD-WABE:CD=171234,DAR=STATION; ADD-WABE:CD=181234,DAR=STATION; ...
It is recommended to turn off displaying the station number since the OpenScape 4000
shows
the station number (in this case it would be the token number 98xxxx).
CHANGE-ZAND:TYPE=ALLDATA2,DSPOWNNO=NO;
A route needs to be configured to be used later in the AMO LDAT:
ADD-RICHT:MODE=LRTENEW,LRTE=lrt1,LSVC=VCE, NAME="ROUTE OpenScape 4000",TGRP=tg1;
The AMO LODR (Out-Dial Rule) adds a 1 to the KXXXX and dials the token number 1KXXXX:
ADD-LODR:ODR=ODR1,CMD=OUTPUSLE,DGTS=1; ADD-LODR:ODR=ODR1,CMD=ECHO,FIELD=1; ADD-LODR:ODR=ODR1,CMD=END;
AMO LDAT specifies that the dialed number has to be rerouted back to the OpenScape
4000,
LATTR=RERTEINT:
ADD-LDAT:LROUTE=LRT1,LVAL=1,TGRP=TG1, ODR=ODR1,LAUTH=1,LATTR=RERTEINT;
All on-base-numbers within the OpenScape 4000 have to be configured individually with
a
timeout as an indication that the number is complete if there is no additional digit
dialed
(or '#') within the timeout.
ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP=7-1234-T, LROUTE=lrt1,LAUTH=1; ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP=8-1234-T, LROUTE=lrt1,LAUTH=1; ...
Numbers that don't reside within the OpenScape 4000 can be routed immediately to the
base
switch.
Route to the base switch:
ADD-RICHT:MODE=LRTENEW,LRTE=lrt2,LSVC=VCE, NAME="RTE TO BASE",TGRP=tg1;
Out-Dial Rule for calls to the base switch:
ADD-LODR:ODR=ODR2,CMD=ECHO,FIELD=1; ADD-LODR:ODR=ODR2,CMD=ECHOALL; ADD-LODR:ODR=ODR2,CMD=END;
LDAT for calls to the base switch:
ADD-LDAT:LROUTE=LRT2,LVAL=1,TGRP=TG1,ODR=ODR2, LAUTH=1;
Dial-Patterns of all calls to base switch phones:
ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP=2-XXXX-T, LROUTE=lrt2,LAUTH=1; ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP=3-XXXX-T, LROUTE=lrt2,LAUTH=1; ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP=4-XXXX-T, LROUTE=lrt2,LAUTH=1; ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP=5-XXXX-T, LROUTE=lrt2,LAUTH=1; ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP=6-XXXX-T, LROUTE=lrt2,LAUTH=1; ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP=7-XXXX-T, LROUTE=lrt2,LAUTH=1; ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP=8-XXXX-T, LROUTE=lrt2,LAUTH=1;
Dial-Patterns of all calls to the DSN:
ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP=2-XXXX-Z, LROUTE=lrt2,LAUTH=1; ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP=3-XXXX-Z, LROUTE=lrt2,LAUTH=1; ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP=4-XXXX-Z, LROUTE=lrt2,LAUTH=1; ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP=5-XXXX-Z, LROUTE=lrt2,LAUTH=1; ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP=6-XXXX-Z, LROUTE=lrt2,LAUTH=1; ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP=7-XXXX-Z, LROUTE=lrt2,LAUTH=1; ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP=8-XXXX-Z, LROUTE=lrt2,LAUTH=1;