168.2.1 ADD-SCSU

The ADD command will only be completed successfully if the following preconditions are met: the required station numbers must be entered in the dial plan (DAR=STN), the relevant module must have a free circuit and the required classes-of-service must be set up.

The parameter PEN designates the port equipment number (LTG-LTU-SLOT-CCT) to which the device with the STNO (station number) is connected. If this parameter is missing, a search is made automatically for an available equipment number in the system which is compatible with the other parameter values. For signed off and floating stations the PEN is ignored without an advisory message.

The connection type (parameter CONN) defines how a station is connected to the system: Either via direct line (DIR) or off premised via TMDNH or SLMA board (OPST1/OPSSLMA). This information is kept in a PEN-specific memory. This is the reason why it does not move with the subscriber during signoff/signon process but remains tied together the physical port (PEN).

Please note when specifying ranges:
Ranges and/or strings of single values may be entered for STNO, but not for the parameter PEN. In this case, a single entered PEN is used as a starting point for the automatic port search.

Exception: Automatic port search for ANATE’s does not consider SLMAR-PEN, even if a SLMAR-PEN is entered as starting point for the search.

Automatic port search for ANATECM’s considers only SLMAR-PEN’s.

The device configuration for which the PEN is to be assigned is defined by the parameter DVCFIG.

Non-voice terminals can only be used by the user if the basic classmark (BASIC) for the relevant service has been added (AMO COSSU) to his class-of-service.

If INS=Y (default), the added connection together with all voice and non-voice terminals will be transferred to the dependability system for further processing. When all preconditions are met, the relevant terminal will be taken into operation.
If INS=N, the subscriber remains in a state which will not be processed by the dependability system, the terminal will not be taken "into operation", and advance provision will only be made with respect to the data required. AMO DSSU allows the terminal to be "ACTIVATED" , "DEACTIVATED" at a later stage. The exact state of the terminal can be queried using AMO SDSU.
The LCOS-Parameters for voice and data are mandatory, because of path selection is always done by Least Cost Routing mechanism. If a device has no data equipment, the LCOSD-Parameters are required but without effect.

Procedure Overview


Command Code	Parameter
ADD-SCSU	STNO=<number>,[PEN=<gg-u-sss-cc>],DVCFIG=<param
	,DPLN=<number>,ITR=<number>,
	,COS1=<number>,COS2=<number>
	,LCOSV1=<number>,LCOSV2=<number>
	,LCOSD1=<number>,LCOSD2=<number>
	,[SPDC1=<number>],[SPDC2=<number>]
	,[COSX=<number>],[SPDI=<number>],[COFIDX=<param>
	,[CCTIDX=<number>],[SPEC=<param>],[DIAL=<param>]
	,[DHPAR=<param>],[RCBKB=<param>],[RCBKNA=<param>]
	,[TEXTSEL=<param>],[INS=<param>]
	,[ACKST=<param>],[SSTNO=<param>],[ALARMNO=<number>]
	,[PULSTYPE=<param>],[PULSLEV=<param>]
	,[HMUSIC=<number>],[CONN=<param>],[FLASH=<param>]
	,[DTMFBLK=<param>],[PMIDX=<number>]
	,[NEONMWI=<param>];

Examples

Create Station 311 as AUXDIGI. The PEN is determined automatically by the AMO.

Input:

ADD-SCSU:STNO=311,DVCFIG=AUXDIGI,DPLN=0,ITR=0,LCOSS1=1,LCOSS2=1,LCOSD1=2,LCOSD2=2,COS1=1,COS2=6;

Output:

H06: 311 THIS STATION IS CONFIGURED AT PEN 1-1-97-1.
H11: 311 CONTROL HAS BEEN PASSED TO CALL PROCESSING FOR STATION ACTIVATION

Assign subscriber 3653 with an ANATE voice terminal at a specific PEN.

Input:

ADD-SCSU:STNO=3653,PEN=1-2-121-5,DVCFIG=ANATE,DPLN=0,ITR=0,COS1=9,
COS2=9,LCOSV1=9,LCOSV2=9,LCOSD1=9,LCOSD2=9,DIAL=VAR;

Output:

H06: 3653 THIS STATION IS CONFIGURED AT PEN 1-2-121-5.
H11: 3653 CONTROL HAS BEEN PASSED TO CALL PROCESSING FOR STATION ACTIVATION

Assign 3 ANATEs with charge metering. The required SLMAR-Port is determined automatically by AMO. The search for free PENs should start at 1-1-43-0 (in this example, the circuits 0,1,3 are assumed to be already seized)

Input:

ADD-SCSU:STNO=2161&&2163,PEN=1-1-43-0,DVCFIG=ANATECM,DPLN=0,ITR=0,COS1=9,COS2=8, LCOSV1=7,LCOSV2=6,LCOSD1=5,LCOSD2=4,PULSTYPE=POL12,PULSLEV=VEFF5;

Output:

H45: THE AUTOMATIC PEN SEARCH FOR FREE PENS TAKES PLACE IN LTU SHELVES WITH SOURCE-GROUP=1 (SEE AMO UCSU).
H33: 2161 FOR DVCFIG = ANATECM CHARGE PULSE DURATION AND PAUSE CAN BE CHANGED BY AMO PTIME.
H06: 2161 THIS STATION IS CONFIGURED AT PEN 1-1-43-2
H11: 2161 CONTROL HAS BEEN PASSED TO CALL PROCESSING FOR STATION ACTIVATION
H33: 2162 FOR DVCFIG = ANATECM CHARGE PULSE DURATION AND PAUSE CAN BE CHANGED BY AMO PTIME.
H06: 2162 THIS STATION IS CONFIGURED AT PEN 1-1-43-4
H11: 2162 CONTROL HAS BEEN PASSED TO CALL PROCESSING FOR STATION ACTIVATION
H33: 2163 FOR DVCFIG = ANATECM CHARGE PULSE DURATION AND PAUSE CAN BE CHANGED BY AMO PTIME.
H06: 2163 THIS STATION IS CONFIGURED AT PEN 1-1-43-5
H11: 2163 CONTROL HAS BEEN PASSED TO CALL PROCESSING FOR STATION ACTIVATION

${DocTitle}, ID: ${DocID}

© 02/2025 Mitel Networks Corporation. - All rights reserved.
Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG.
All other trademarks herein are the property of their respective owners.