199.5.2 Advisories

 
H01:
PLEASE SPECIFY LTG NUMBER
H02:
SYSTEM UNIT NOT DUPLICATED
H03:
PARAMETER LOOPBACK HAS BEEN IGNORED
H04:
TEST IN PROGRESS
H05:
PARAMETER TSI HAS BEEN IGNORED
H06:
PARAMETER SELFTEST IS SET YES AUTOMATICALLY
H07:
TEST: EXTERNAL REMOTE LOOPBACK TMD/T1DN/SLMN-T1
 
-----------------------------------------------
 
BOARD <pen> ** BOARD IS REMOTE BOARD **
 
** INTERNAL REMOTE LOOPBACK (IDC) ACTIVATED **
 
PLEASE CONTINUE TEST ON LOCAL BOARD (TEST-TSU:LOOPBACK = EDC)
H08:
TEST: EXTERNAL REMOTE LOOPBACK TMD/T1DN/SLMN-T1
 
-----------------------------------------------
 
BOARD <pen> ** BOARD IS LOCAL BOARD **
 
** TEST EDC COMPLETED **
 
PLEASE DEACTIVATE THE INTERNAL REMOTE LOOPBACK ON THE REMOTE BOARD
 
(TEST-TSU:....LOOPBACK = IDL)
H09:
TEST: EXTERNAL REMOTE LOOPBACK TMD/T1DN/SLMN-T1
 
-----------------------------------------------
 
BOARD <pen> ** BOARD IS REMOTE BOARD **
 
INTERNAL REMOTE LOOPBACK (IDC) DEACTIVATED
H10:
AFTER CALL OF ’DIAGNOSE-TSU’ TEST ERRORS ARE TREATED AUTOMATICALLY
 
BY FAULT ANALYSIS ! IN THIS CASE FA CAN CAUSE LOCKS,SWITCHING OR RESTARTS!
 
(IN CASE OF ERRORS SIGNALLING MESSAGES ARE DISPLAYED
 
ON SCREEN IF OUTPUT IS ASSIGNED RIGHT)
H11:
TEST: EXTERNAL REMOTE PAYLOAD LOOPBACK TMD/SLMN-T1
 
--------------------------------------------------
 
BOARD <pen> ** BOARD IS REMOTE BOARD **
 
** INTERNAL REMOTE PAYLOAD LOOPBACK (IPON) ACTIVATED
 
PLEASE CONTINUE TEST ON LOCAL BOARD (TEST-TSU: ..LOOPBACK = EDC)
H12:
TEST: EXTERNAL REMOTE PAYLOAD LOOPBACK TMD/SLMN-T1
 
--------------------------------------------------
 
BOARD <pen> ** BOARD IS REMOTE BOARD **
 
INTERNAL REMOTE PAYLOAD LOOPBACK (IPON) DEACTIVATED
H13:
FRAME TABLE CAN NOT BE LOADED FROM HARD DISK
H14:
TSI IS SET TO 1 FOR LINEPOWER TEST
H15:
ACTIONS OF FA CAN LAST ABOUT 5 MINUTES WHEN MAJOR DEFECTS
 
OCCUR ON CSN HIGHWAY !
H16:
ALL TERMINALS AT THIS CIRCUIT ARE TESTED
H17:
THE TESTS CAN BE STOPPED USING CTRL/X
 
WHILE DISPLAYING TEST RESULTS (PLEASE DO NOT USE ’CANCEL:..’ TO STOP AMO TSU !)
H18:
LOCKS ARE THE RESULTS OF THIS TEST ! IT MAY NOT BE STARTED IN NORMAL OPERATION !! LAST CHANCE TO STOP (CTRL/X) !
H19:
SUBSCRIBER STATE HAS CHANGED DURING MEASUREMENT ! THE MEASUREMENT RESULTS ARE PROBABLY NOT USEFUL ! PLEASE REPEAT THE TEST !
H20:
SUBSCRIBER STATE (ONHHOOK OR OFFHOOK) CAN NOT BE DETERMINED AT THE MOMENT (THERE IS NO DIFFERENCE IN MEASUREMENT BETWEEN ONHOOK AND OFFHOOK LOOP).
H21:
SIMPLE LINECHECK : SEE IMPORTANT INFORMATION IN SERVICE MANUAL ! THIS TEST SHOULD BE CARRIED OUT A FEW TIMES ! (TEST USEFUL UP TO 8 KM ONLY)
H22:
TIMESLOT IS SET TO ’1’
H23:
TIMESLOT IS CHOSEN BY RTO.
H24:
HIGHWAY IS CHOSEN BY RTO.
H25:
THE BOARD HIGHWAY TEST CAN ONLY BE STARTED WITHOUT DIFFICULTIES, IF IT IS NOT ACTIVATED AS A ROUTINE TEST BY AMO FUNSU. PLEASE CHECK BY USING AMO FUNSU, WETHER THE TEST IS ACTIVE.
 
IF IT IS SO, THE ROUTINE TEST HAS TO BE DEACTIVATED BEFORE RUNNING THE MANUAL TEST AND IT HAS TO BE ACTIVATED AFTERWARDS.
H26:
WRONG USAGE OF THIS FUNCTION CAN CAUSE HEAVY PROBLEMS IN THE SWITCH ! PLEASE CHECK THE INPUT PARAMETERS AND SKIP FUNCTION IF YOU ARE NOT SURE ! DO YOU WANT TO CONTINUE THIS FUNCTION ?
H27:
COMMAND EXECUTION SUCCESSFULLY DONE
H28:
COMMAND HAS NOT BEEN EXECUTED
 
 
${DocTitle}, ID: ${DocID}
 © 02/2025 Mitel Networks Corporation. -  All rights reserved.
 Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG.
 All other trademarks herein are the property of their respective owners.