215.4 Messages and Advisories

215.4 Messages and Advisories

215.4.1 Error messages

SPECIFY CODE FOR DIAL PULSE DEVICES

SPECIFY CODE FOR PARTNER DIGIT ANALYSIS RESULT

ENTRY FOR CODE @@@@@@@@@@@@@@@ IS NOT POSSIBLE DUE TO SHORTAGE OF MEMORY SPACE (@@@ TABLES)

(The following steps help minimize memory space requirements:

•

create digit analysis results for only a few CPSs and so that they are DPLN-independent

•

create DAR STN as far as possible for complete (!) blocks of 10, 100 or 1000 units.)

DELETION OF NUMBER @@@@@@@@@@@@@@@ NOT POSSIBLE DUE TO SHORTAGE OF MEMORY SPACE (CD TABLES)

(When (individual) stations are being deleted, excessive memory may be required if a number of stations belonging to different blocks of ten is specified.)

FOR CODE @@@@@@@@@@@@@@@ THIS DIGIT ANALYSIS RESULT WAS ALREADY ADDED

FOR CODE @@@@@@@@@@@@@@@ ANOTHER DIGIT ANALYSIS RESULT WAS ALREADY ADDED

CALL PROGRESS STATE @@ NOT PERMITTED FOR THIS DIGIT ANALYSIS RESULT

NO SPECIAL CHARACTERS ARE POSSIBLE FOR THIS DIGIT ANALYSIS RESULT

DPLN GROUP MAY NOT BE SPECIFIED FOR THIS DIGIT ANALYSIS RESULT

SECOND CODES (CD2/CDDP2) ARE NOT PERMITTED
- FOR A DIGIT ANALYSIS RESULT THAT DOES NOT BELONG TO A PAIR
- IF CHECK=N

ACTION NOT POSSIBLE - CODE @@@@@@ IS STILL ASSIGNED TO A STATION OR KNDEF ENTRY

(Any additional information must first be deleted with the appropriate AMOs.)

DELETION OF CODE @@@@@@ FOR DPLN @@@@ AND CPS @@ NOT POSSIBLE AS ATTENDANT GROUP STILL ASSIGNED

DELETION OF CODE @@@@@@ FOR DPLN @@@@ AND CPS @@ NOT POSSIBLE AS ROUTE STILL ASSIGNED

FOR CODE RANGES, BOTH LIMITS MUST HAVE THE SAME NUMBER OF DIGITS

TARGET RANGE EXCEEDS THE DECIMAL CODE RANGE

(In the destination range, the number of digits in the calculated upper limit is not the same as for the specified lower limit. However, only ranges with an equal number of digits are permitted.)

CHANGING OF CODE @@@@@@ NOT POSSIBLE AS USED BY ANOTHER DAR

CHANGING OF CODE @@@@@@ NOT POSSIBLE AS SAME DAR ALREADY ASSIGNED

FOR DPLN @@ THE DIGIT ANALYSIS RESULT @@@@@@@@ HAS NOT YET BEEN ADDED

(The correct DAR sequence has not been observed. The digit analysis result shown must be created first.)

FOR DPLN @@ THE DIGIT ANALYSIS RESULT @@@@@@@@ HAS NOT YET BEEN DELETED

(The correct DAR sequence has not been observed. The digit analysis result shown must be deleted first.)

DAR @@@@@@@@ HAS NOT YET BEEN ADDED INDEPENDENTLY OF DPLN,I.E. WITHOUT SPECIFICATION OF SPECIFIC DPLN

(See explanation for F18:.)

DAR @@@@@@@@ HAS NOT YET BEEN DELETED INDEPENDENTLY OF DPLN, I.E. WITHOUT SPECIFICATION OF SPECIFIC DPLN

(See explanation for F19:.)

SPECIAL CHARACTERS ARE PERMITTED ONLY IN SINGLE ENTRIES FOR CODE

ONLY SINGLE CODE ENTRIES ARE PERMITTED FOR A PAIRED DAR

SPECIAL CHARACTERS IN THE SPECIFIED CODES ARE NOT COMPATIBLE

(The numbers concerned must belong to the same special character category:

Cat DEC : digits 0...9 only

Cat 12-key: as for DEC, also *, #

Cat 16-key: as for DEC and 12-key, also A,B,C,D

IF DIAL PULSE STATION CODE IS SPECIFIED, ONLY ONE CODE IS PERMITTED

WITH ENTRY OF A CODE RANGE, LOWER LIMIT MUST BE <= UPPER LIMIT

THIS DIGIT ANALYSIS RESULT IS NOT PERMITTED FOR DIAL PULSE DEVICES

(Therefore, it makes no sense to specify CDDP.)

THE SPECIFICATION OF A DIAL PULSE STATION CODE IS NOT PERMITTED

ENTRY OF CDDP2 WITHOUT ENTRY OF CDDP IS NOT PERMITTED

PARAMETERS @@@@@ AND @@@@@ HAVE THE SAME VALUES

(Some combinations of numbers make it necessary to enter two values for certain parameters. In particular, this occurs if one number is contained in a higher number in the combination.)

ENTRY OF CPS2 WITHOUT ENTRY OF CD2 IS NOT PERMITTED

IF CD IS EXPANDED, NEITHER CDDP NOR CD2 MAY BE SPECIFIED

(A digit analysis result is already assigned to this code. At this stage, the DAR can only be entered when expanding the CPS allocation. Therefore, a (new) CDDP or CDDP2 is not permitted.)

EXPANSION OF PARAMETER @@@@@@@@ IS NOT PERMITTED

(The digit analysis result is already assigned to this number with a different CPS allocation. In this case, the DAR must be assigned to a different number.)

AN ENTRY FOR CODE @@@@@@ IS NOT POSSIBLE BECAUSE A @@@@ DIGIT ANALYSIS RESULT ALREADY EXISTS HERE.

PLEASE DISPLAY USING: DIS-WABE:GEN,@@@@@@&&@@@@@@;

(The assignment of central office and tie trunk digit analysis results or station and individual attendant console digit analysis results to the same number is not permitted.)

ENTRY FOR CODE @@@@@@ IS NOT POSSIBLE BECAUSE A CENTRAL OFFICE OR TIE TRUNK DIGIT ANALYSIS RESULT ALREADY EXISTS

(The assignment of central office and tie trunk digit analysis results to numbers which are contained in higher numbers (e.g. 12 and 125) is not permitted.)

DELETION OF CODES @@@@@@@@@@@@@@@ IS NOT POSSIBLE BECAUSE THERE IS EITHER NO SUCH ENTRY OR THE ENTRY DOES NOT CORRESPOND EXACTLY WITH THE DATA INPUT

(The entries in the DPLN table do not match the data in the DELETE command. The parameter values entered in the DELETE command must match the entries in the table exactly, i.e. not only the CD, but also the CPS and DPLN allocations are checked. Use the DISPLAY function to view the table entries for the number (CD) concerned.)

SPECIFY CODE FOR DIAL PULSE DEVICES FOR PARTNER DIGIT ANALYSIS RESULT

CODES @@@@@@ - @@@@@@ NOT DELETED

(This error message occurs only in conjunction with F11. If individual stations of a specified block of 10, 100 or 1000 cannot be deleted, the stations concerned are shown in F11. In order to prevent such stations from unnecessarily occupying memory space, the entire range is not deleted. If individual stations within a range are to be kept, they must be explicitly left out of the range to be deleted, i.e. several smaller ranges must be entered instead of one large one.)

SOURCE AND TARGET RANGES OVERLAP

(If two ranges overlap, the second range must initially be specified outside the first range (in the ADD command), and then changed to the actual range desired by means of a CHANGE command.)

NO DIGIT ANALYSIS RESULTS COULD BE CHANGED

SPECIFY DESTNO > 0

STATIONS AND DIGIT ANALYSIS RESULT WITH ROUTING OR ATTENDANT GROUP ASSOCIATIONS CANNOT BE CHANGED

(If no digit analysis result is explicitly specified in the change command, then this error message means that no station, route or attendant DARs were changed.)

NO CHAINED VALUES ARE PERMITTED FOR CODE

CODE VALUES 0 TO 9 ONLY FOR DAR FLASHCD

SPECIFIED DAR NOT PERMITTED FOR THIS COMMAND

ACTION IMPOSSIBLE DUE TO SHORTAGE OF CD TABLES

ACTION IN RULO NOT POSSIBLE FOR STNO @@@@@@ BECAUSE VALUE FOR DIMSU-PARAMETER @@@@@@ IS TOO SMALL

PARAMETERS DESTNO, CDNEW, ARN, CFREMVAR AND CFREMSE
ARE VALID ONLY ALTERNATIVELY
EXCEPTION: CFREMVAR AND CFREMSE CAN BE ENTERED TOGETHER

IF 01 TO 99 IS ENTERED FOR ARN CD IS VALID ONLY UP TO 4 DIGITS

ARN IS ALLOWED ONLY FOR DAR OWNNODE

FOR CD @@@@@@ WITH DAR OWNNODE AND ARN > 00
CDNEW IS VALID ONLY UP TO 4 DIGITS

DNNO IS INVALID
VALUE RANGE: <0-29> - <0-253> - <0-999>

ACTION NOT POSSIBLE FOR CODE @@@@@@ - RCG IS STILL ASSIGNED (AMO ACDSD)

FOR CODE STARTING WITH @@@@@@ A DIGIT ANALYSIS RESULT WAS ALREADY ADDED
PLEASE DISPLAY USING: DIS-WABE:GEN,@@@@@@&&@@@@@@,0&&15;

LOWER BOUND OF @@@@@@@@ FOR DAR=PARK MUST END IN 0

NOT ENOUGH CONSECUTIVE ACCESS CODES AVAILABLE
FOR DAR=PARK @@@@@@ - @@@@@@

ACCESS CODE FOR DAR PARK CANNOT BE CHANGED
-> DELETE AND ADD WITH NEW ACCESS CODE

CODE <xxxxxx> IS STILL ASSIGNED AS A COMBI CODE (AMO RUFUM)

DELETION OF CODE <xxxxxx> FOR DPLN <xxxx> AND CPS <xx> NOT POSSIBLE AS GATEWAY NUMBER STILL ASSIGNED

CHINA_7_DIG_NUMBERING IS NOT ACTIVE AND NUNP IS ACTIVE , ARN CAN NOT BE USED

CODE <RNR> IS NOT A STN OR A COMBINATION OF OWNNODE AND STN FOR VNR

PARAMETER DESTNO CAN NOT BE SET, AS NO DEFAULT NODE IS ASSIGNED (AMO KNDEF).

DELETION OF CODES <xxxxxx>-<xxxxxx> IS NOT POSSIBLE AS ROUTE STILL ASSIGNED.
IF YOU ARE SURE TO DELETE WABE ENTRIES , FIRSTLY YOU SHOULD DELETE THESE ROUTES BY USING FOLLOWING COMMANDS :
CHA-WABE:<xxxxxxxxxxxx>&&<xxxxxxxxxxxx>,0;

DELETION OF CODE <xxxxxx> IS NOT POSSIBLE AS ROUTE STILL ASSIGNED.
IF YOU ARE SURE TO DELETE WABE ENTRY , FIRSTLY YOU SHOULD
DELETE THESE ROUTES BY USING FOLLOWING COMMANDS :
CHA-WABE:<xxxxxxxxxxxxxx>,0;

IT IS NOT POSSIBLE TO ADD <xxxxxx> AS DPLN INDEPENDANT. PLEASE ADD THIS NUMBER AS DPLN DEPENDANT (E.G. DPLN = 0&&15).

OWNNODE CAN BE ADDED/DELETED ONLY DPLN INDEPENDENT, SINCE IT IS A VNR SYSTEM.

OWNNODE IS POSSIBLE FOR ALL DPLN (0&&15) TOGETHER. IT CAN NOT BE DELETED FOR SUBSETS OF DPLN (0&&15).

DELETION OF CODE <xxxxxx> IS NOT POSSIBLE WHEN IT IS ASSIGNED TO UFIP DEVICES. ONLY CHANGE IS ALLOWED.

DELETION OF CODE <xxxxxx> IS NOT POSSIBLE AS ROUTE STILL ASSIGNED. PLEASE CHECK AMO KNDEF CONFIGURATION.

${DocTitle}, ID: ${DocID}

© 02/2025 Mitel Networks Corporation. - All rights reserved.
Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG.
All other trademarks herein are the property of their respective owners.