14.6.1.2.2. Configuration in Node 10-69-200 
An LEGK should also be active in node 10-69-200. As the configuration
procedures for nodes 10-69-200 and 10-69-100 are identical, this section
only lists the appropriate AMO commands for the steps described above.
Step 0:
CHANGE-ZANDE:TYPE=ALLDATA,GATEKPR=YES;
Step 1:
ADD-BFDAT:FCTBLK=1,FUNCTION=HG3550,BRDBCHL=BCHAN60&BCHAN120; CHANGE-BFDAT:CONFIG=CONT,FCTBLK=1,FUNCTION=HG3550,LINECNT=1, UNITS=3; /* 30 B channels for HG3550 functionality (IP trunking, SIP trunking, SIP subscriber) CHANGE-BFDAT:CONFIG=OK,FCTBLK=1,ANSW=YES; /* Close the configuration ADD-BCSU:MTYPE=IPGW,LN=1,LTU=2,SLOT=49,PARTNO="Q2316-X ", FCTID=1,LWVAR="0",FCTBLK=1,BCHL3550=30,ALARMNO=0;
Step 2:
ADD-CGWB:LTU=2,SLOT=49,SMODE=NORMAL, IPADDR=1.69.21.80,NETMASK=255.255.255.0,TRPRHSIPQ=10; ADD-CGWB:LTU=2,SLOT=49,SMODE=NORMAL, IPADDR=1.69.21.80,NETMASK=255.255.255.0,TRPRHSIP=10;
Step 3:
CHANGE-CGWB:MTYPE=CGW,LTU=2,SLOT=49,TYPE=GLOBIF,DEFRT=1.69.21.254;
Step 4:
CHANGE-CGWB:MTYPE=CGW,LTU=2,SLOT=49,TYPE=LEGKDATA,GWNO=2;
Step 5:
CHANGE-CGWB:MTYPE=CGW,LTU=2,SLOT=49,TYPE=LEGKDATA, GWNO=2,REGEXTGK=NO;
SSA:
CHANGE-CGWB:MTYPE=CGW,LTU=1,SLOT=49,TYPE=SIPTRSSA,SIPREG=NO;
ERH:
CHANGE-CGWB:MTYPE=CGW,LTU=2,SLOT=49,TYPE=SIPTRERH,GWAUTREQ=NO;
IMPORTANT:
The SIPREG and REGEXTGK
parameters must always have the same value.
Step 6:
ADD-BUEND:TGRP=50,NAME="IP TRUNK GWID 2 ",NO=30; ADD-TDCSU:OPT=NEW,PEN=1-02-049-0,COTNO=36, COPNO=32,DPLN=0,ITR=0, COS=2,LCOSV=1,LCOSD=1, CCTN="CIRCUIT from GW2",PROTVAR="ECMAV2",SEGMENT=8,ISDNIP=00, ISDNNP=0,TRACOUNT=31,SATCOUNT=MANY,NNO=1-69-499, ALARMNO=12, COTX=36,CCHDL=SIDEA,CLASSMRK=EC&G711,TCCID="IP RS", TGRP=50,SRCHMODE=DSC,INS=Y,DEV=HG3550IP,BCHANNEL=1&&30,BCNEG=N,BCGR=1,LW PAR=0(=Master),DMCALLWD=YES;CHANGE-CGWB:MTYPE=CGW,LTU=<ltu>,SLOT=<slot>,TYP=ASC,PRIO=PRIO1,VAD=YES;
Step 7:
The GKREG contains the configuration for both HG 3500 boards. Here,
GWNO=2 is now the local gateway in node 10-69-200 with the attributes
INTGW and HG3550V2 and SIPQ/SIP, while GWNO=1
(the partner gateway in node 10-69-100) contains the attributes EXTGW,
HG3550V2 and SIPQ/SIP in this system. The parameter REGGW
is not necessary because the gateway does not have to register at another
gateway.
ADD-GKREG:GWNO=1,GWATTR=EXTGW&HG3550V2&SIPQ or SIP,GWIPAD DR=1.69.11.80,DIPLNUM=0,DPLN=0,LAUTH=1; ADD-GKREG:GWNO=2,GWATTR=INTGW&HG3550V2&SIPQ or SIP,DIPLNUM=0,DPLN=0,LAUTH=1;