27.2.2 CHANGE-BCSU

•

It is only possible to change code numbers of modules within the same module-line-type (e.g. SLMA).

Exception: The change of some boards with newer HW modules is possible even though the module-line-type is different and is handled AMO internally (e.g. STMD<->STMD2, SLMS<->SLMS2, DIUS2<->DIUN2,...).

If the module is not already blocked, the AMO blocks it. After the change is carried out, the module is put back into service.

•

In the case of a DIUC, the parameters FIDX1/2 and LWPAR1/2 of the associated PCM paths can be modified.

•

With the new branch "HWYBDL" the access to the upper (F) or lower (A) highwaybundle of a board can be set, to use a previously by AMO UCSU configured overlay configuration. At the moment, bundle "F" can only be used for STMI, DIUN2- and DIUN4 boards.

•

With the new branch "HWYBDL" the number of usable b-channels can be reduced and also reset to the original value for each configured function on the HG3500 board, respectively the pre-reserved amount of circuits (for trunks) and/or b-channels (for subscribers) can be re-configured to usable circuits/b-channels.

The calculation of values for automatic b-channel reduction is always done if a value is specified for the according parameter - but it is not possible to configure more than the maximum possible values.

Procedure Overview


Command Code	Parameter
CHANGE-BCSU	TYPE=PARTNO,[LTG=<number>],[LTU=<number>]
	,[SLOT=<number>],[PARTNO1=<string>]
	,PARTNO2=<string>,[FCTID1=<number>]
	,[FCTID2=<number>],[ALARMNO=<number>];

	\|TYPE=DIU,[LTG=<number>],LTU=<number>
	,SLOT=<number>,{(min 1)LWPAR1=<string>,FIDX1=<string>
	,LWPAR2=<string>,FIDX2=<string>};

	\|TYPE=SIGNOFF,[LTG=<number>],LTU=<number>,SLOT=<number>
	,[CCT=<number>],[TSI=<number>],[DEVTYPE=<param>]
	,[COFIDX=<number>],[OPS=<param>];

	\|TYPE=RELEASE,[LTG=<number>],LTU=<number>,SLOT=<number>
	,[CCT=<number>],[TSI=<number>];

	\|TYPE=FLOWCTRL,[LTG=<number>],[LTU=<number>]
	,[SLOT=<number>],[ACTFC=<number>],[STERM=<number>]
	,[LTERM=<number>],[PTERM=<number>];

	\|TYPE=HPA,[LTG=<number>],LTU=<number>
	,SLOT=<number>,[MACADDR=<hex>]
	,[TDMLAW=<number>];

	\|TYPE=HWYBDL,[LTG=<number>],[LTU=<number>]
	,[SLOT=<number>],PARTNO=<string>
	,[FCTID1=<number>],[HWYBDL=<param>];

	\|TYPE=TMD,[LTG=<number>],LTU=<number>
	,SLOT=<number>,[LWPAR=<number>],[FIDX=<string>];

	\|TYPE=IPGW,[LTG=<number>],LTU=<number>
	,SLOT=<number>,[IPADDR=<number>]
	,[BCHL3530=<number>],[BCHLSIP=<number>]
	,[BCHL3550=<number>],[BCHLWAML=<number>]
	,[BCHL3570=<number>],[CHNGRSL=<number>];

Examples

Change the SLMA module with the code number Q2041-X and the parameters LTG=1, LTU=1, SLOT=31 to an SLMA module with the code number Q2057-X100.

Input:

CHANGE-BCSU:PARTNO,1,1,31,,"Q2057-X100";

Change all SLMA modules of LTG 1 with the code number Q2041-X to SLMA modules with the code number Q2057-X100.

Input:

CHANGE-BCSU:PARTNO,1,,,"Q2041-X","Q2057-X100";

Output:

H01: BG 1.1. 25 CHANGED - IN SERVICE
H01: BG 1.1. 31 CHANGED - OUT OF SERVICE (NPR)
. . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . .

Change the highwaybundle of a DIUN2 to bundle "F":

CHANGE-BCSU:HWYBDL,1,1,37,Q2196-X,1,F;

Change pre-reserved trunk circuits to configurable HG3550 circuits for IP gateway by means of parameter CHNGRSL.

Prerequists are pre-reserved HG3550 circuits:

ADDRESS :  LTG  1   LTU 3    SOURCE GROUP 1    ALARMNO-LTU 0
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
     |           |        |   |S|H|AL-|N|            |            |
     | ASSIGNED  | MODULE |FCT|E|W|ARM|P| INSERTED | HW- | MODULE
PEN | MODULE    | TYPE   |ID |C|Y|NO |R| MODULE     |STATE INFO  | STATUS
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
  55 | Q2324-X510 STMI4      1 * A   0|*| UNKNOWN    |            | UNACH
     +--------------------------------+-+------------+------------+------------
     | IP ADDRESS : 192.168. 11. 55         B-CHANNELS : 120    BCHLCNT : 120
     | BLOCK NO   :  11                     PRERESERVED LINES ASSIGNED :   NO
     |  1. FUNCT  : HG3570        1 LINES   B-CHANNELS :  21    BCHLCNT :  21
     |  2. FUNCT  : HG3530       70 LINES   B-CHANNELS :  59    BCHLCNT :  59
     |  3. FUNCT  : HG3550        1 LINES   B-CHANNELS :  10    BCHLCNT :  10
     |  4. FUNCT  : HG3550R       3 LINES   B-CHANNELS :  30    BCHLCNT :  30
     | SECURITY STATUS: 1:[ ]  2:[ ]  3:[ ]  4:[ ]  5:[ ]  6:[ ]  7:[ ]  8:[ ]
     |  (SEE BOTTOM)    9:[ ] 10:[ ] 11:[ ] 12:[ ] 13:[ ] 14:[ ] 15:[ ] 16:[ ]
     +--------------------------------+-+------------+------------+------------

Input:

CHA-BCSU:IPGW,1,3,55,,,,,,,2;

Result:

ADDRESS :  LTG  1   LTU 3    SOURCE GROUP 1    ALARMNO-LTU 0
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
     |           |        |   |S|H|AL-|N|            |            |
     | ASSIGNED  | MODULE |FCT|E|W|ARM|P| INSERTED   |    HW-     | MODULE
PEN | MODULE    | TYPE   |ID |C|Y|NO |R| MODULE     |STATE INFO  | STATUS
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
  55 | Q2324-X510 STMI4      1 * A   0|*| UNKNOWN    |            | UNACH
     +--------------------------------+-+------------+------------+------------
     | IP ADDRESS : 192.168. 11. 55         B-CHANNELS : 120    BCHLCNT : 120
     | BLOCK NO   :  11                     PRERESERVED LINES ASSIGNED :  YES
     |  1. FUNCT  : HG3570        1 LINES   B-CHANNELS :  21    BCHLCNT :  21
     |  2. FUNCT  : HG3530       70 LINES   B-CHANNELS :  59    BCHLCNT :  59
     |  3. FUNCT  : HG3550        3 LINES   B-CHANNELS :  30    BCHLCNT :  30
     |  4. FUNCT  : HG3550R       1 LINES   B-CHANNELS :  10    BCHLCNT :  10
     | SECURITY STATUS: 1:[ ]  2:[ ]  3:[ ]  4:[ ]  5:[ ]  6:[ ]  7:[ ]  8:[ ]
     |  (SEE BOTTOM)    9:[ ] 10:[ ] 11:[ ] 12:[ ] 13:[ ] 14:[ ] 15:[ ] 16:[ ]
     +--------------------------------+-+------------+------------+------------

Manual reduction of b-channels. In this example the number of b-channels is reduced for HG3530 but set to the for each function in maximum possible value for HG3550 and HG3550-WAML (not configured).

Input:

CHA-BCSU:IPGW,1,3,55,,40,,120,120;

Output:

H31: THE AMOUNT OF AVAILABLE B-CHANNELS ON CGW BOARD HAS BEEN CHANGED !
     PLEASE CHECK THE RESOURCE MANAGER CONFIGURATION (ALSO AMO-CGWB)
H32: IF THE B-CHANNEL PARAMETER IS SPECIFIED, THE AVAILABLE B-CHANNELS ON CGW
     FUNCTIONS IS SMALLER/EQUAL AS THE CONFIGURED VALUES FOR CGW FUNCTIONS !
     THE RESOURCE MANAGEMENT IS ALSO AFFECTED BY SPECIFIYING THIS
     PARAMETER, THEREFORE FEWER B-CHANNELS WILL BE CONFIGURED IN TOTAL.
H39: THE PARAMETERS FOR CHANGING THE NUMBER OF B-CHANNELS WILL BE IGNORED IF
     THE ACCORDING FUNCTION IS NOT CONFIGURED.
H35: THE PROCESSED CHANGES HAVE NEEDED A DEACTIVATED STMI BOARD.
     THE BOARD IS INITIATED TO BE TAKEN IN SERVICE AGAIN RIGHT NOW.

Result:

ADDRESS :  LTG  1   LTU 3    SOURCE GROUP 1    ALARMNO-LTU 0
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
     |           |        |   |S|H|AL-|N|            |            |
     | ASSIGNED  | MODULE |FCT|E|W|ARM|P| INSERTED   |    HW-     | MODULE
PEN | MODULE    | TYPE   |ID |C|Y|NO |R| MODULE     |STATE INFO  | STATUS
-----+-----------+--------+---+-+-+---+-+------------+------------+------------
  55 | Q2324-X510 STMI4      1 * A   0|*|            |            | NPR
     +--------------------------------+-+------------+------------+------------
     | IP ADDRESS : 192.168. 11. 55         B-CHANNELS : 120    BCHLCNT : 101
     | BLOCK NO   :  11                     PRERESERVED LINES ASSIGNED :  YES
     |  1. FUNCT  : HG3570        1 LINES   B-CHANNELS :  21    BCHLCNT :  21
     |  2. FUNCT  : HG3530       70 LINES   B-CHANNELS :  59    BCHLCNT :  40
     |  3. FUNCT  : HG3550        3 LINES   B-CHANNELS :  30    BCHLCNT :  30
     |  4. FUNCT  : HG3550R       1 LINES   B-CHANNELS :  10    BCHLCNT :  10
     | SECURITY STATUS: 1:[ ]  2:[ ]  3:[ ]  4:[ ]  5:[ ]  6:[ ]  7:[ ]  8:[ ]
     |  (SEE BOTTOM)    9:[ ] 10:[ ] 11:[ ] 12:[ ] 13:[ ] 14:[ ] 15:[ ] 16:[ ]
     +--------------------------------+-+------------+------------+------------

OpenScape 4000 V10, Volume 1: AMO Descriptions, Service Documentation, Issue 5, ID: P31003H31A0S107057620

© 09/2025 Mitel Networks Corporation. - All rights reserved.
Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG. All other trademarks herein are the property of their respective owners.