145.5 Error Messages and Advisories

145.5.1 Error Messages


F01:	IF DCHAN2 IS ENTERED > 0, DCHAN1 MUST BE GREATER THAN 0
F02:	DCHAN1 AND DCHAN2 MUST HAVE DIFFERENT VALUES
F03:	BLOCK <blockno> IS OF CIRCUIT TYPE <circtype>
F04:	PARAMETER LNCD: SET THE VALUES "DLPT" AND "DLCD" ALTERNATIVELY ONLY
F05:	BLOCK <blockno> IS NOT ALLOCATED
F06:	BLOCK <blockno> IS ALREADY ALLOCATED
F07:	BLOCK <blockno> IS ALLOCATED TO THE CIRCUIT WITH PEN <gg-u-sss-cc>
F08:	PARAMETER COS: "CDRAC", "CDRS", "CDRC" CANNOT BE CHAINED WITH "NCDR"
F09:	PLEASE USE THE VALUES "RTA1" TO "RTA6", "TA" AND "RTA" ALTERNATIVELY ONLY
F10:	PARAMETER PARTCD: USE THE VALUES "400E" AND "EMD" ALTERNATIVELY ONLY
F11:	PARAMETER PARTCD: USE THE VALUES "ASAT" AND "CSAT" ALTERNATIVELY ONLY
F12:	PARAMETER COS: USE THE VALUES "EXTEND" AND "PU" ALTERNATIVELY ONLY
F13:	PARAMETER COS: USE THE VALUES "OVR" AND "KN" ALTERNATIVELY ONLY
F14:	INADMISSIBLE INPUT VALUE FOR THE PRE-SET DIGIT
F15:L	PARAMETER CTYPE: "HOME", "CO", "TOLL" CANNOT BE CHAINED WITH "N"
F16:	DEVICE TYPE "S2COD" (AMO TDCSU) IS NOT PERMITTED FOR ANY OF THE ALLOCATED
	CIRCUITS IF PARAMETER SMD IS CHANGED FROM "N" TO "Y"
F17:	IF PARAMETER SMD IS SET TO "Y", ALL ALLOCATED CIRCUITS MUST THEN HAVE THE PRIORITY VALUE "0" (AMO REFTA)
F18:	PARAMETER TONES: "DTN1", "DTN2", "DTNT", "DTE" CANNOT BE CHAINED WITH "NULL"
F19:	PARAMETER SPDCDSS: "SPD", "SPDC" CANNOT BE CHAINED WITH "N"
F20:	IF THE VALUE <SPD/SPDC> HAS BEEN SPECIFIED FOR SPDCDSS, THEN THE PARAMETER <DGTPR/DGTPRC> MUST CONTAIN A VALID CODE
F21:	IF THE VALUE SPDC IS SPECIFIED IN PARAMETER SPDCDSS, SPDC1 MUST THEN BE SET TO 0 (ZERO)
F22:	IF ONLY A SINGLE SPEED DIALING CODE HAS BEEN ASSIGNED, THEN THE VALUES OF DGTPR AND DGTPRC MUST BE IDENTICAL
F23:	<DGTPR/DGTPRC> DOES NOT LEAD TO DAR <SPDC1/SPDC2> IN THE DPLN
F24:	PARAMETER LNTYPE: USE THE VALUES "COPPER" AND "OWG" ALTERNATIVELY ONLY
F25:	PARAMETER LNTYPE: AERIAL IN ITSELF IS NOT ALLOWED AS A SINGLE VALUE
F26:	PARAMETERS SMD AND MASTER MUST BOTH BE SET TO „Y“ OR „N“
F27:	NOT ENOUGH MEMORY FOR INFO FIELD IN DATAPOOL TO WRITE THE INFO, INCRASE AT LEAST BY @@ WITH THE HELP OF COMMAND ADD-DIMSU:DPINFO= <>;
F28:	MAXIMUM NUMBER OF INFO FIELDS ARE USED, NUMBER HAS TO BE INCREASED AT LEAST BY @@ WITH THE HELP OF COMMAND ADD-DIMSU:INFO=<>;
F29:	INDEX OUT OF RANGE
F30:	BLNO=@@ IS STILL ASSIGNED TO AT LEAST ONE CIRCUIT OF A CDG BOARD AND HENCE CANNOT BE DELETED. DISPLAY SETTINGS WITH DISPLAY-LWPAR:TYPE=CDG,BLNO=@@,LWPARREF=YES;
F31:	COULD NOT LOAD DATA SUBSYSTEM @@@@@@@@@@@@@@@@@ FROM HARD DISK.
F32:	@@@@@@@@@@@@@@@@@ NOT FOUND ON HARD DISK!
F33:	@@@@@@@@@@@@@@@@@ OF TYPE @@@@@ NOT IN THE RANGE FROM @ TO @@@.
F34:	AN ERROR OCCURED WHILE COPYING THE @@@@@@@ @@@.
F35:	FOLLOWING VALUES CAN NOT BE CONFIGURED BECAUSE THEY ALREADY EXIST IN THE MAPPING TABLE: @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@
F36:	THE INPUT VALUES FOR PARAMETER @@@@@@@ MUST BE DIFFERENT.
F37:	THE SPECIFIED VALUE FOR PARAMETER PRIMDXTG HAS NOT BEEN CONFIGURED, BECAUSE DXTG = @@@ IS NOT CONFIGURED IN THE MAPPING TABLE.
F38:	EITHER ALL OR NONE OF THE PARAMETERS DXTGPOS, DXTG AND ITR MUST BE SPECIFIED. PLEASE CHECK INPUT BECAUSE THE ERROR COULD HAVE RESULTED FROM WRONG DXTGPOS OR DXTG FIELD VALUES.
F39:	THE GIVEN BLNO IS BIGGER THAN WITH AMO DIMSU,PARAMETER TBLMAX RESERVED MEMORY.
F41:	THE TMD BLOCK TYPE HAS NO DEV AND INFO FIELD, AND THE SEARCH CRITERIAS BY INFOPAT, DEV AND FORMAT ARE IGNORED.

OpenScape 4000 V10, Volume 1: AMO Descriptions, Service Documentation, Issue 5, ID: P31003H31A0S107057620

© 09/2025 Mitel Networks Corporation. - All rights reserved.
Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG. All other trademarks herein are the property of their respective owners.