215.2.1
ADD-WABE
With this command it is possible to create 1 DAR for one or more CDs or several DARs for one CD.
In the case of digit analysis result pairs, it is possible to assign both partners for the same station number if the desired call progress states are completely mutually exclusive.
If parameter DPLN is omitted, the DAR is created without DPLN branching for all DPLN groups.
When DARs for central offices and tie trunks are created, the AMO prevents the assignment of another CO/tie trunk DAR to the same station number using different CPS‘s only. The assignment is also prevented in the case of various long station numbers for CO and tie trunk DARs that correspond up to the number of digits of the shorter station number.
When a DAR for station is created, the AMO prevents the assignment of an individual attendant console DAR to the same station number using different CPS‘s only and vice versa. This is because stations are stored in station line memory only depending of the station number, but data cannot be stored depending on CPS.
The DAR NETRTE can be preset for a suitable route with the AMO WABE. The connection between all DARs NETW, NETWFAX and NETWDTE with the same DESTNO and a suitable NETRTE must be set up with the AMO
RICHT
.
If CHECK is not specified, CHECK=ALL is taken as default value.
The DAR STN can be marked as external with DESTNO as supplementary information. For operating reasons, the DESTNO should only be specified for individual STNs in the ADD command but for ranges in the CHA command. In the case of regeneration, normal ADD commands (without DESTNO) are also created for the external STN, followed by a list of CHA commands sorted in ascending order added to the end.
Station numbers for DAR=STN should, where possible, be set up in closed ranges. This applies both to external and internal STNs, as no external/internal distinction is made in WABE. This saves a significant amount of memory and runtime.
The specification of a value greater than 00 for the parameter ARN is only permitted in the case of a CD containing up to 4 digits and the DAR OWNNODE. The CD is then assigned to the ARN as office code for call number display. This action overwrites any previous office code assignment.
The assignment of CFREMVAR and/or CFREMSE is only permitted in the case of the DARs AFWDREM, DFWDREM and FWDREM.
Station number categories
A number of special characters cannot be dialed from all terminals. The digits are therefore split into categories:
a)
A,B,C,D only for devices with a 16-key keypad
b)
*, # also for devices with a 12-key keypad
c)
0...9 for all devices
The highest value that occurs must correspond in both specified access codes.
Examples:
CD=A35
CD2=C*
permitted
CD=#5
CD2=*48
permitted
CD=#A37
CD2=B
permitted
CD=A
CD2=#
not permitted
CD=*12
CD2=123
not permitted
The following table provides a summary of the possible combinations of input parameters.
Table 53
Combinations of possible input parameters
Add
CHECK
CD
CD2
2
1. Indep. DAR w/o SC
in any case
DARw/oSC
2. " " with SC
PART,N
DAR w SC
3. " " " SC
(ALL)
DAR w SC
DARw/oSC
4. DAR pair w/o SC
(ALL),PART
DARw/oSC
DARw/oSC
5. " " " SC
N
DARw/oSC
6. " " with SC
(ALL)
DAR w SC
DARw/oSC
DAR w SC
DARw/oSC
7. " " " SC
PART
DAR w SC
DAR w SC
8. " " " SC
N
DAR w SC
Explanation:
SC: Special Characters
Digit analysis result without special characters
Digit analysis result with special characters
CD,CD2: Code 0 to 9, *, #, A to D
,2: Code for dial pulsing devices 0 to 9
Procedure Overview
Command Code
Parameter
ADD-WABE
CD=<key-num>,[DPLN=<number>],[CPS=<number>]
,DAR=<param>,[CHECK=<param>],[=<number>]
,[CD2=<key-num>],[CPS2=<number>],[2=<number>]
,[DESTNO=<number>],[ARN=<number>]
,[CFREMVAR=<param>],[CFREMSE=<param>];
Examples
1.
Assign the DAR=STN (station) to station numbers 3200-3299 for all call progress states allowed for STN.
Input:
ADD-WABE:CD=3200&&3299,DAR=STN;
2.
Assign the DAR ’saved number redial’ in DPLN group 2, for the CPSs ’station prefix dialing’, ’in-house consultation’, ’CO consultation’; code = *11 for dial pulsing = 5111.
Input:
ADD-WABE:CD=*11,DPLN=2,CPS=5&8&9,DAR=SNR,=5111;
3.
Assign the DAR ’add station to hunt group, voice’ in DPLN group 2 for all CPSs allowed for AHTVCE, with code = *56, dial pulsing = 5156. Since the DAR is part of a DAR pair, reporting of the partner code = #56 or 5256 in the CPS = ’station prefix dialing’.
Input:
ADD-WABE:CD=*56,DPLN=2,DAR=AHTVCE,=5156,CD2=#56,CPS2=5,2=5256;
4.
Assign the DAR ’network point’, without taking individual DPLN groups into account, in all CPSs provided for CDs 4800 to 4999, with DESTNO 213.
Input:
ADD-WABE:CD=4800&&4999,DAR=NETW,DESTNO=213;
5.
Assign the DAR ’add station to hunt group, voice’ in DPLN group 3, for all CPSs permitted for this DAR and CD = *86. Assign the partner DAR ’DHTVCE’ with CD2 = #86, without associated DP station numbers.
Input:
ADD-WABE:CD=*86,DPLN=3,DAR=AHTVCE,CHECK=PART,CD2=#86;
CPS expansion
Each DAR is assigned a fixed range of possible CPSs (display with DIS‑WABE:TYPE=CPS). By specifying the parameter CPS, a CD for a DAR can also be added for a subset of the possible CPSs of a DAR. The CD can be extended to the other CPSs by repeating the ADD action. Please note that the parameters , CD2 and 2 must not be specified. The ADD action must be activated separately for CPS expansion for the , CD2 and 2 station number. A CPS expansion is only possible for the applicable
CPS range
for the relevant DAR, provided a DAR has not yet been assigned for this CD/CPS combination (neither this nor another).
Example:
1.
Add a DAR pair with CPS subset (specify parameter CD2)
Input:
ADD-WABE:CD=*75,CPS=1,DAR=CAFAFWD,CD2=#75,CPS2=1;
2.
CPS expansion for the new station numbers of the DAR pair (parameter CD2 must not be specified - separate ADD command necessary for partner DAR)
Input:
ADD-WABE:CD=*75,CPS=5,DAR=CAFAFWD;
ADD-WABE:CD=#75,CPS=5,DAR=CAFDFWD;
3.
Add a DAR for devices with dial pulse only option with DAR subset (specify parameter )
Input:
ADD-WABE:CD=*76,CPS=2,DAR=HUNT,=876;
4.
CPS expansion for the new station numbers of the DAR for devices with dial pulse only option (parameter must not be specified - separate ADD command necessary for station number)
Input:
ADD-WABE:CD=*76,CPS=3,DAR=HUNT;
ADD-WABE:CD=876,CPS=3,DAR=HUNT;
OpenScape 4000 V10, Volume 1: AMO Descriptions, Service Documentation, Issue 5
, ID:
P31003H31A0S107057620
©
09/2025
Mitel Networks Corporation. - All rights reserved.
Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG. All other trademarks herein are the property of their respective owners.