AANT

With this parameter "synchronized" announcements can be handled like "asynchronous" announcements. The application is for second announcements with music which are injected immediately. With this parameter, the device handler controls the TMOM to activate the announcement device immediately. The COT parameter ANOD is essential. (In this case, the announcement device is connected to a/b, the c/d wires on the TMOM must be jumpered.)

x

ABAN

Line with answer before synchronized announcement is injected (for incoming seizure).

x

ABPD

Line with answer before postdial

x

ACKB

Backward release acknowledgment

x

ACKF

Forward release acknowledgment

x

Accept a-law in bearer-capability, that is, convert to y-law

x

USA

ANIC

Line with ANI Codogram (transmission with incoming seizure, see COT value ANIC), CIS

x

CIS

ANIO

ANI without tone, CIS

x

CIS

ANIW

ANI with tone, CIS

x

CIS

ANNC

With incoming seizure in analog tie traffic, a local announcement (SIU tone, AMO ZAND) instead of a dial tone is injected.

The DTN parameter must not be set!

x

ANS

This parameter is for lines supporting the signalling method "Answering".

x

APPR

Set only for test purposes and approvals

x

ASEG

APDU segmentation not allowed (CorNet-NQ) As the default for OpenScape 4000, APDUs that are too long and do not fit in an ECMA/ISO standardized Facility Information Element, will be segmented (CorNet-NQ Issue V2.2 APDU SEGMENTATION). Parameter must be set for all CorNet-NQ protocol versions, HV1.0 IM and later, if you do not want APDU segmentation.

x

ASNM

Display ASN.1 error messages (QSIG)

This parameter is used for error diagnosis!

x

AST1

ANI supervision timer 1 if ANI without tone, (for route1/ trunk1)

When the OpenScape 4000 is installed in CIS countries, the CO might request the A station's number for outgoing calls. If the AST1 parameter is set this request is accepted within a time span of 1-60 sec. The A station's number is then transmitted to the CO.

See also parameter DT1A.

x

CIS

AST2

ANI supervision timer 2 if ANI without tone, (for route2/ trunk2)

When the OpenScape 4000 is installed in CIS countries, the CO might request the A station's number for outgoing calls. If the AST2 parameter is set this request is accepted within a time span of 1-60 sec. The A station's number is then transmitted to the CO.

See also parameter DT2A.

x

CIS

BR64

With DP, the pulse series are transmitted with a make/break ratio of 60/40 ms according to the TKO. If the parameter is not set, so-called speed dialing (for example, 30/30 ratio) is used for transmission.

x

BTN1

Busy tone timeout 1 for incoming calls,

for times with DTIM2, TYPEDH=GEN, BTN1, see also NBAR (for example, Poland)

x

Poland

BTN2

Busy tone timeout 2 for incoming calls,

for times with DTIM2, TYPEDH=GEN, BTN2, see also NBAR (for example, Poland)

x

Poland

BTN3

Timeout for busy status for incoming calls. (times with DTIM2, TYPEDH=GEN, BTN3)

Calls to busy stations go to retesting within this time (only applies if COT: CWBS is set). After timeout the connections are released backwards. During this time the remote CO can override, provided the station's relevant COS allows this. Calls with other negative results are immediately released backwards.

x

Italy

BTOF

Busy tone in response to "CO offering" instead of attendant intercept (exact renunciation tone request). Applies to terminating (incoming) seizure.

x

CCM

CCS voice connection directly using meet me is possible

x

CCR

Release with CCS comfort after every task

x

CCTN

With CCE and CCM: wait for an audible tone after the A block has been transmitted.

x

COCN

CO consultation call possible.

x

COEI

Determines whether the IAM/SAM message must evaluate the "Class-Index" (for example, China)

With MFC-R2 signalling, COE is transmitted in transit cases.

x

China

CO tone in transit traffic for CO trunks

x

CTGF

Continuous tone in the event of group failure TL-CF.

For analog tie traffic with CF signalling in remote incoming blocking state or resp. line alarm, the continuous tone in the event of group failure of the integrated carrier frequency device is processed accordingly.

x

DITW

Incoming MSI seizure leads to a defined destination.

If DITW is set, the digit information from the DGTPR memory (parameter DGTPR in the AMO TACSU) is transmitted to the digit analysis for incoming seizure. This results in automatic connection setup to the predefined station.

x

DT1A

ANI delay timer 1 used with ANI procedures without tone (for direction 1/trunk1), CIS

If the A station number requested by the CO was transmitted in a codogram, this timer is used to delete the request.

See also AST1.

x

CIS

DT2A

ANI delay timer 2 used with ANI procedures without tone (for direction 2/trunk2) CIS

If the A station number requested by the CO was transmitted in a codogram, this timer is used to delete the request.

See also AST2.

x

CIS

DTBR

Line with renewed dialtone instead of backward releasing (only with DP!).

This parameter must be set, if the B station goes on hook and the A station wants to call a further station in the B system. The line is not released. Dialtone is injected in the B system to signal ready-to-dial condition.

x

DTM1

Make/break ratio for DTMF dialing, variant 1 (80/80 ms).

The DTMF parameter must be set.

x

DTM2

Make/break ratio for DTMF dialing, variant 2 (150/150 ms)

The DTMF parameter must be set.

x

DTM3

Make/break ratio for DTMF dialing, variant 3 (200/200 ms)

The DTMF parameter must be set.

x

DTM4

Make/break ratio for DTMF dialing, variant 4 (300/300 ms)

The DTMF parameter must be set.

x

DTMF

Line with DTMF dialing (one of the DTM1-4 parameters must be set).

x

DTN

With incoming seizure the dialtone is injected according to the COT setting (NTON, DTNI, DTNE, ANNC)

x

DTT

Dialtone instead of start-dialing signal. With outgoing traffic the dialtone is evaluated using dialtone receivers. Then the digits are transmitted.

x

DTV

Line with multiple dialtones

x

EMOV

This parameter must be set to allow emergency override/disconnect for incoming analog tie trunks.

x

EO10

Emergency override via analog tie trunks with E&M or CF signalling with 10 instead of 11 pulses. (Interworking for example, with EMS601)

x

EOD

This parameter is for lines supporting the "End-of-dialing" signalling method.

End-of-dialing is transmitted if 'dialing complete' was recognized. With analog tie traffic this signal has no meaning (for example, STN free/busy)

x

EODA

End-of-dialing analyzed (interworking with GTD systems)

This parameter must be set, if weighted end-of-dialing (free/busy) is to be evaluated with analog tie traffic using CF signalling and a GTD system as partner node. With "End-of-dialing busy" from the remote system manual override on the busy station and retesting can be registered.

Attention: the COP parameter EOD must be set.

x

FDGT

Line is switched through immediately, no digits are sent.

x

ICAC

Acknowledge first digit with line signals (MFP2), China.

With MFP2 signalling and this parameter set, the first received digit is acknowledged with the appropriate line signal. This is required for the control of the line signal INITIAL_CODE_ACKNOWLEDGE in the Chinese signalling variant DIUC32/64 for the MFP2 signalling method.

x

China

IDP1

Interdigit pause 1, that is, the pause between the pulse dialing series. One of the parameters IDP1-4 must be specified (associated time, parameter IDGT1 in AMO DTIM2).

x

IDP2

Interdigit pause 2, that is, the pause between the pulse dialing series. One of the parameters IDP1-4 must be specified (associated time, parameter IDGT2 in AMO DTIM2).

x

IDP3

Interdigit pause 3, that is, the pause between the pulse dialing series. One of the parameters IDP1-4 must be specified (associated time, parameter IDGT3 in AMO DTIM2).

x

IDP4

Interdigit pause 4, that is, the pause between the pulse dialing series. One of the parameters IDP1-4 must be specified (associated time, parameter IDGT4 in AMO DTIM2).

x

ILRW

Italian Railway

x

Italy

IMEX

Conversion of implicit to explicit number with DSS1.

If the OpenScape 4000 is used as DSS1 trunk and the "TYPE OF NUMBER" = "UNKNOWN" for incoming seizure, the transmitted prefixes of the B number are deleted. The prefixes set with AMO TDCSU are used for this purpose.

If this parameter is not set, the "TYPE OF NUMBER" = "SUBSCRIBER" must be set.

x

IVSN

Adjustment of the OpenScape 4000 interface on IVSN (CIS)

x

CIS

L3AR

Registration of the ISDN layer 3 advisory messages.

If this parameter is set, layer 3 error messages are output on the operating terminal in case of protocol violations.

This parameter only applies for ISDN circuits.

x

LA03

Level ANI outgoing -3.5 dB0 (alternative to LAO0, default value -7 dB0) CIS

x

CIS

LAI8

Level ANI incoming -0.8 dB0 (default value -4.3 dB0) CIS

x

CIS

LAO0

Level ANI outgoing 0 dB0 (alternative to LAO3, default value -7dB0) CIS

x

CIS

LCOS

Limitation of the LCOS index to 32

x

LCR

LKNQ

This parameter is set if the partner PBX is a OpenScape 4000 and the networking protocol Cornet-NQ/Qsig is used.

This parameter must not be set, if the partner PBX is a remote system.

x

LSI0

Level MFR-Shuttle incoming 0 dB0 (alternative to LSI3, default value -7 dB0) CIS

x

CIS

LSI3

Level MFR-Shuttle incoming 3.5 dB0 (alternative to LSI0, default value -7 dB0) CIS

x

CIS

LSO0

Level MFR-Shuttle outgoing 0 dB0 (alternative to LSO3, default value -7 dB0) CIS

x

CIS

LSO3

Level MFR-Shuttle outgoing -3.5 dB0 (alternative to LSO0, default value -7 dB0) CIS

x

CIS

LSRB

Line supervision for analog tie traffic with E&M signalling with remote blocking. If the seizure acknowledgment is missing a remote blocking signal is transmitted (Spain).

x

Spain

LSUP

Line with line supervision.

If this parameter is set the line is supervised. This parameter only applies for analog trunks with line supervision.

The reseizure lockout is implemented on the board (LW) (release to the line is always acknowledged):

a) For lines with supervision for line interruptions in idle state

b) For lines with supervision for line interruptions in the state "Waiting for receipt of seizure acknowledgment" or "Start-dialing signal" (with E&M only)

x

LWCC

Line with continuity check in case of seizure (CSN7, China)

x

China

MCHI

Channel ID can be repeated in the restart message

x

North American Analog Trunk

x

USA

NBAR

No busy tone on the line after release (for example, Poland)

See BTN1/2/3 for busy tone.

x

NO1A

No 1A signalling method.

With lines without end-of-dialing, the end-of-dial detection is deactivated using signalling method 1A.

x

NOAN

No answer on receipt of first charge pulse.

If the parameter is not set, the reception of a charge pulse equals answering.

This applies only for signalling methods without answer (analog).

x

NOCH

Line without charge (CIS).

If this parameter is set, the device handler transmits the classes of service COSSU and NOCHRG to the LW. The corresponding E&M circuit must be configured with "Answering".

If this parameter is not set or if NCOHRG is not set in the AMO COSSU, no corresponding message is sent to the LW.

x

CIS

NONA

Send no name.

If this parameter is set, the OpenScape 4000 does not transmit names and ignores received names.

This parameter is only relevant for the Swissnet 3 protocol, Swissnet 3 allows the transmission of names as UINFO information elements.

x

NOTO

No tone between end-of-dialing and answer.

x

NOTR

No transparency mode between ECMA and ISO Qsig

x

NSDL

Auxiliary parameter for AMO COP. It allows the setting of TIM1/2 on its own without the SDL parameter which will otherwise be automatically set.

x

NTON

Identification of a pulsed tone as dialing tone.

Applies to trunk and tie lines. Must be set, if the first tone to be evaluated is a pulsed dialing tone. (Default continuous tone)

x

PDIG

The first digit is treated as an MLPP precedence digit

x

MLPP

PDP1

Pause before first dial string, only with analog lines. At least one of the parameters PDP 1/2/3/4 must be set (for time, see AMO DTIM2, PDLY1).

x

PDP2

Pause before first dial string, only with analog lines. At least one of the parameters PDP 1/2/3/4 must be set (for time, see AMO DTIM2, PDLY2).

x

PDP3

Pause before first dial string, only with analog lines. At least one of the parameters PDP 1/2/3/4 must be set (for time, see AMO DTIM2, PDLY3).

x

PDP4

Pause before first dial string, only with analog lines. At least one of the parameters PDP 1/2/3/4 must be set (for time, see AMO DTIM2, PDLY4).

x

PNIO

This parameter allows activation of controlled disconnect, for example, with E&M priorities, on analog tie lines.

x

PRMT

Line with preemption signaling

x

MLPP

R176

Digital device is configured for API

x

RBLK

Line with remote blocking.

If the circuit is blocked either manually or by soft restart, a blocking signal is transmitted to the partner system.

x

RCLA

Timed recall to AC. If after an incoming seizure the backward release is not acknowledged, a timed recall is carried out. (Or: if the external A station waits after the internal B station has released, the A station is signaled at the AC.)

Timer: DTIM1, TYPEDH=MFCDID, RBANSW=xx

x

RDIG

The first/second digit is treated as an MLPP RouteCodeDigit

x

MLPP

RF0C

Repeat factor 0 for ANI-codogram, CIS

The transmitted codogram is not repeated.

x

RF1C

Repeat factor 1 for ANI-codogram, CIS

The transmitted codogram is repeated once.

x

RF2C

Repeat factor 2 for ANI-codogram, CIS

The transmitted codogram is repeated twice.

x

RF3C

Repeat factor 3 for ANI-codogram, CIS

The transmitted codogram is repeated three times.

x

RGSZ

Dialing after register seizure

This parameter applies for analog lines with two seizure types ("Directional seizure"). The parameter must be set in the A system if the second seizure type is used and the destination to be seized is transmitted from the A system via the line.

If the destination address for the "directional seizure" is stored as fixed presetting in the remote system, the parameter must not be set.

x

RLSA

This parameter is for lines supporting "Backward release after release".

x

RLSB

This parameter is for lines supporting "Backward release when busy".

x

RMSG

If this parameter is set, a RESTART message is sent to the remote PBX when layer 1 is activated.

x

RRST

If this parameter is set, the Restart Indicator, which was transmitted in the RESTART message from the remote PBX during RESTART_ACK, is sent back unmodified.

This parameter must be set if not all B channels of an S2 line have been configured, for example, for connections to special servers or to T1 trunks via a/u law converters.

x

SACK

Seizure acknowledgment on the line is transmitted, if the seizure was recognized and accepted. As soon as the acknowledgment is received, either digits can be dialed after a signal interval or the line waits for further signals such as start-dialing or dialing tone.

x

SDL

The start-dialing signal is transmitted, if the seizure was recognized and the system is ready for dialing. When the start-dialing signal is received, digits can be dialed after a signal interval. Together with SDL, a start-dialing signal time must be set, see parameters TIM. If TIM1/2 is not specified, the AMO automatically sets TIM1

x

SEDL

This parameter is used to identify circuits for series/supplementary dialing.

This parameter is used in power utility company networks and allows the local announcement of the selected node to be heard. This parameter can only be set in association with DP on the line. With outgoing seizure end-of-dialing is activated immediately.

x

SFRM

Line with special mode.

(For a detailed description, see comments in the AMO description after the parameter descriptions.)

x

SPD

Device handler recognizes speed calling.

x

SPTR

If this parameter is set, the ISDN service information (BC, HLC, or LC) are routed transparently through the system and are not mapped into the OpenScape 4000 service profiles.

BC - Bearer Capability HLC - High Layer Compatibility LLC - Low Layer Compatibility

Rule: Always set this parameter up to and including EV1.0.

From EV2.0 the meaning of this parameter was reversed, that is, do not set this parameter as standard.

x

TDED

Line with time dependent CO dialtone to the station.

x

TIE

If this parameter is set, incoming traffic on MFC lines is processed as tie traffic.

Used to configure the trunk circuits BWFIN (R2 Finland) and SOCFR (R2 France) as "tie trunks" (trick solution!).

x

TIM1

If this parameter is set, the start-dialing signal timer 1 is used for monitoring the start-dialing time on lines using the start-dialing signal (STADIAL1 in the AMO DTIM2).

x

TIM2

If this parameter is set, the start-dialing signal timer 2 is used for monitoring the start-dialing time on lines using the start-dialing signal (STADIAL1 in the AMO DTIM2).

x

TIM3

If this parameter is set, the start-dialing signal timer 3 is used for monitoring the start-dialing time on lines using the start-dialing signal (STADIAL1 in the AMO DTIM2).

x

TIM4

If this parameter is set, the start-dialing signal timer 4 is used for monitoring the start-dialing time on lines using the start-dialing signal (STADIAL1 in the AMO DTIM2).

x

TRAC

Line with pre-tracing, signalling of emergency disconnect is possible.

Only in connection with analog tie lines with E&M or CF signalling and the feature "Emergency override". The neighboring node must also be a OpenScape 4000 system. If a disconnect request has already been signaled, the signal "line traced" (12 pulses) is transmitted to the neighboring node before the destination number is transmitted. Because of this, this node is alerted that in case of "all trunks busy" a circuit of the desired trunk group is to be released immediately.

x

UU7B

The Display Info in the User Information Element is coded with 7 Bit and an Extension Bit.

x

WOT2

Only for trunk circuits (DP/MSI) if a "pulsed" dial tone is to be evaluated as further dial tone marker.

x

ZMFV

Send out a digit at MFV after end of dialing

x