Collapse AllExpand All

5.6.9.1. Configuration of 'Partial-integration-RG' solution Previous topic Parent topic Child topic Next topic

  • Configuration of 'Partial-integration-RG' solution
  • Configuration of DIUS2
    The DIUS2 is configured identical to other DIUS2 in system (e.g. for CORNET-NQ networks). The DIUS2-Loadware need not be informed by AMO LWPAR, that a PBXXX is connected to it. The OpenScape 4000 switch gets the reference clock directly from the DIUS2. Therefore if PBXXX is connected to a DIUS2, the LWPAR-Parameter CDG=NO has to be configured for the DIUS2. AMO commands (applicable to an empty Database, important commands are shown bold):
    Please pay attention to the functional id of the PBXXX
  • Configuration of the PBXXX board as 'Ring Generator': 
    ADD-BCSU:MTYPE=RG, LTG=1, LTU=1, SLOT=67, PARTNO="Q6401-X", FCTID=1;
  • Configuration of DIUS2
    • DIMSU configuration for DIUS2 (all dimsu needed for DIUS2) 
      ADD-DIMSU:TYPE=ADMCC, CCIDXS=2000; 

ADD-DIMSU:TYPE=BASIC, LODEN=2000, PRI=20, TRK=100, SG=100, 
NWBCHL=600, CRCP=50, DPLNCD=800, ....; 

ADD-DIMSU:TYPE=SYSTEM, PERMDL=100, ..;
    • Configuration fo LTG, LTU and DIUS2 
      ADD-UCSU:UNIT=LTG, LTG=1, SIPARTNO="Q2234-X "; 

ADD-UCSU:UNIT=LTU, LTG=1, LTU=1, LTPARTNO="Q2248-X"; 
ADD-BCSU:MTYPE=DIU, LTG=1, LTU=1, SLOT=61, PARTNO="Q2096-X200",  LWVAR=0;
    • Basic configuration of LCR 
      ADD-WABE:CD=19, DAR=OWNNODE; 

ADD-WABE:CD=16, DAR=TIE; 

CHANGE-ZAND:TYPE=ALLDATA, NNO=100, NODECD=19; 

ADD-COP:COPNO=5; 

ADD-COT:COTNO=20; 

ADD-BUEND:NO=30, TGRP=23, NAME="QV-DPNSS1"; 

CHANGE-LWPAR:TYPE=DIUS2, BLNO=2, CDG=N; /* CDG MUST BE SET TO "NO" */
    • Configuration of trunk (use a proper LCOSS and LCOSD to get the necerssary access and a node number ) 
      ADD-TDCSU:OPT=NEW, PEN=1-1-061-00, BCGR=1, CCT="CDG-DPNSS1", 
COTNO=20, COPNO=5, LCOSV=1, LCOSD=1, PROTVAR=ECMAV2, DEV=S2CONN, 
TGRP=23, LWPAR=2; 

CHANGE-REFTA:TYPE=CIRCUIT, PEN=1-1-061-00, PRI=80;
      OpenScape 4000 can accept the clock from DPNSS1 (depending on prio and error counters) And if the circuit is configured through CDGM to retrieve th clock from DPNSS/DASS
      OR
      OpenScape 4000 does not accept clock from DPNSS-Network but delivers it (PRIO=0) (for details see also Section 46.5.6, "Network Clock Supply"). OpenScape 4000 should always accept the clock from a DASS circuit and never deliver it.
${DocTitle}, ID: ${DocID}
© 03/2026 Mitel Networks Corporation. All rights reserved. Mitel and the Mitel logo are trademark(s) of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH & Co. KG. All other trademarks herein are the property of their respective owners.