5.21.2.2.2. Closed numbering of network in OpenScape 4000 specific numbering
plan 
In the following example, the subscribers on Level 0 in Munich should
be closed-numbered in the OpenScape 4000 specific numbering plan. According
to definition, ISDN and PRIVATE are always open-numbered. For this reason,
the configuration for ISDN and PRIVATE remains unchanged for Section .
Again, it should be based in the network topology shown in Figure
55. The numbers are shown in the following table:
|
Node
|
Number UNKNOWN
|
Number ISDN
|
Number PRIVATE
|
|
1-1-100
|
[30]-XXXX 30=area code
|
0-(00)49-(0)89-722-XXXX
|
15-(11)39-(1)719-6051-XXXX
|
|
1-1-400
|
[30]-XXXX 30=area code
|
0-(00)49-(0)89-636-XXXX
|
15-(11)39-(1)719-5116-XXXX
|
|
1-2-200
|
37-XXXX
|
0-(00)49-(0)211-734-XXXX
|
15-(11)39-(1)1573-634-XXXX
|
|
2-1-300
|
39-XXXX
|
0-(00)41-(0)1-636-XXXX
|
15-(11)31-(1)0-536-XXXX
|
Configuration in physical node 1-1-111
Here, only the differences in comparison with Section 41.2.2.1,
"Three-level, open-numbered network/one-level OpenScape 4000 specific
numbering plan" are listed.
- Set the node table:
ADD-KNDEF:NNO=1-1-100,TYPE=OWN,ISDNCC=49,ISDNAC=89,ISDNLC=722, ISDNSK=3,ISDNUL=EXT,PNPL2C=39,PNPL1C=719,PNPLC=6051,PNPSK=4, PNPUL=EXT,NODECD=30,NODECDSK=2; CHANGE-KNDEF:NNO=1-1-100,DFLT=Y;
- Set the own area code for UNKNOWN in WABE:
ADD-WABE:CD=30,DAR=OWNNODE;
- Set the tie line code for Switzerland (NPI=UNKNOWN) in WABE:
ADD-WABE:CD=39,DAR=TIE;
- Set the tie line for Dusseldorf (NPI=UNKNOWN) in WABE:
ADD-WABE:CD=37,DAR=TIE;
- Set closed-numbered subscribers in WABE:
ADD-WABE:CD=001,DAR=NETRTE,CHECK=NO; ADD-WABE:CD=2400&&2499,DAR=STN,DESTNO=4,CHECK=NO; /* Subscriber in 1-1-400 */ ADD-WABE:CD=4000&&4799,DAR=STN,DESTNO=0,CHECK=NO; /* Subscriber in own node */
IMPORTANT:
The number within an area must always be set fully qualified in AMO WABE (e.g. 43xxx is not valid!). - The node connection matrix is to be set for the UNKNOWN numbering plan. You can see
that the
area code is treated like a normal node code in AMO KNMAT.
CHA-KNMAT:NPI=UNKNOWN,LEVEL=0,ONNOL=OWN,DNNOL=ROW, MODCON=OUT,NUMEXT=#####; CHA-KNMAT:NPI=UNKNOWN,LEVEL=0,ONNOL=ROW,DNNOL=OWN, MODCON=IN&TRANSI,NUMRED=#####;
- Set the tie line routes, outdial rules, route elements, and dial pattern plan in LCR
for the
UNKNOWN numbering plan:
/* Open for Node 2-1-300 */ ADD-RICHT:MODE=LRTENEW,LRTE=101,LSVC=ALL,NAME=UNKNOWN, TGRP=74,DNNO=2-0-0; ADD-LODR:ODR=6,CMD=ECHO,FIELD=1; ADD-LODR:ODR=6,CMD=ECHO,FIELD=2; ADD-LODR:ODR=6,CMD=END; ADD-LDAT:LROUTE=101,LSVC=ALL,LVAL=1,TGRP=74,ODR=6; ADD-LDPLN:LDP=39-X,LROUTE=101,LAUTH=1; /* Open for Node 1-2-200 */ ADD-RICHT:MODE=LRTENEW,LRTE=102,LSVC=ALL,NAME=UNKNOWN, TGRP=75,DNNO=1-2-0; ADD-LDAT:LROUTE=102,LSVC=ALL,LVAL=1,TGRP=74,ODR=6; ADD-LDPLN:LDP=37-X,LROUTE=102,LAUTH=1; /* Closed for Node 1-1-400 */ ADD-RICHT:MODE=CD,LRTE=103,CD=001,CPS=0,SVC=ALL, NAME=LCR_VERDECKT,TGRP1=84,DESTNO=4,DNNO=1-1-400; ADD-LODR:ODR=7,CMD=ECHO,FIELD=1; ADD-LODR:ODR=7,CMD=END; ADD-LDAT:LROUTE=103,LSVC=ALL,LVAL=1,TGRP=84,ODR=7,LAUTH=1;
Configuration in other nodes
The setting of the other nodes can be derived from Node 1-1-111.