Section 5.36.3.3.7. Future Expansions

5.36.3.3.7. Future Expansions

If another virtual node were to be added in Germany, the following additional measures would be required:

Configure the virtual node number as OWNNODE.
If the station numbers do not correspond to an existing DPLN group, you may need to configure a new DPLN group.
The new virtual node must be configured with the AMO KNDEF.
The new subscribers must be configured.
The subscribers must then be assigned the LCR profile if this is not already specified by the hardware configuration.
Configure the trunk group with the trunks for this node.
Expansion of LCR level 1:
- For every new city, a new outdial rule must be configured with the number 1xx for Hamburg.
- This outdial rule must be configured for the LCR route with the number of the outdial rule as the LRTE number.
- The new LRTE must be assigned LCR profile 1.
- In addition, LCR profile 2 (Germany) must be expanded to include new source groups.

Expansion of LCR level 2:

A new LTRE must be configured for this source group for all LCR routes from LTRE 3xx onwards (in our example LTRE 3xx to 6xx).
Existing LCR profiles greater than or equal to 3 (3 to 5 in our example) must be expanded to include the new source group.
The new station number must be assigned LCR profile 4 for internal destinations in Germany.

Example:

The system is expanded to include an IPDA shelf in the Reperbahn district. The AP is assigned the LTU number 40. Accordingly, it is assigned source group 40. The virtual node number is 1-1-4 with the node code 94. The ISDN station number is +49 40 2889 – X.

ADD-WABE:CD=94,DAR=OWNNODE,CHECK=N; 

ADD-KNDEF:NNO=1-1-4,TYPE=OWN, ISDNCC=49,ISDNAC=40,
ISDNLC=2889,ISDNSK=4, NODECD=94,NODECDSK=2,DPLN=2,ADPLN=2; 

ADD-SBCSU:STNO=941007,OPT=OPTI,CONN=DIR, PEN=1-40-3-0,
DVCFIG=OPTIIP,COS1=1,COS2=1,LCOSV1=1, LCOSV2=1,LCOSD1=1,LCOSD2=1; 

(CHANGE-SDAT:STNO=941000&&941999,TYPE=DATA1,SRCGRP=40;) 

ADD-BUEND:TGRP=4,NAME="TRUNK GROUP ND 1-1-4",NO=30; 

ADD-TDCSU:OPT=NEW,PEN=1-40-1-0,COTNO=20,COPNO=20,DPLN=0,ITR=0,COS=1,
LCOSV=1,LCOSD=1,CCT="CO Hamburg 194", DESTNO=99,PROTVAR=EDSGER,SEGMENT=1,
ATNTYP=CO,ISDNIP=00,ISDNNP=0,TRACOUNT=8,NNO=1-1-194,TGRP=4,SRCHMODE=ASC,
INS=Y,DEV=S2COD,BCHAN=1&&30,BCNEG=Y,BCGR=1,LWPAR=1, SRCGRP=40; 

ADD-LODR:ODR=103,CMD=OUTPULSE,DGTS=0004940; 

ADD-LODR:ODR=103,CMD=ECHO,FIELD=3; 

ADD-LODR:ODR=103,CMD=NPI,NPI=ISDN,TON=INTERNAT; 

ADD-LODR:ODR=103,CMD=END; 

ADD-LODR:ODR=103,INFO="LODR FOR Hamburg"; 

ADD-RICHT:MODE=LRTENEW,LRTE= 103,LSVC=ALL,NAME="SRC Hamburg",
TGRP=4,DNNO=1-1-194; 

ADD-LDAT:LROUTE=103,TGRP= 4,ODR=103,LAUTH=1,LATTR=RERTEINT; 

CHANGE-LPROF:PROFIDX=1,SRCGRP=40,LRTE=103; 

CHANGE-LPROF:PROFIDX=2,SRCGRP=40,LRTE=200; 

ADD-RICHT:MODE=LRTENEW,LRTE=340,LSVC=ALL,,
NAME="SRC40 INTERNAT",TGRP=4,DNNO=1-1-194; 

ADD-LDAT:LROUTE=340,TGRP=4,ODR=300,LAUTH=1; 

ADD-RICHT:MODE=LRTENEW,LRTE=440,LSVC=ALL,NAME="SRC40 INLAND",
TGRP=4,DNNO=1-1-194; 

ADD-LDAT:LROUTE=440,TGRP=4,ODR=400,LAUTH=1; 

ADD-RICHT:MODE=LRTENEW,LRTE=540,LSVC=ALL,NAME="SRC40 RERT INT",
TGRP=4,DNNO=1-1-194; 

ADD-LDAT:LROUTE=540,TGRP= 4,ODR=300,LAUTH=1,LATTR=RERTEINT;

ADD-LDAT:LROUTE=540,TGRP=4,ODR=300,LAUTH=1; 

ADD-RICHT:MODE=LRTENEW,LRTE=640,LSVC=ALL,NAME="SRC40 RERT NAT",
TGRP=4,DNNO=1-1-194; 

ADD-LDAT:LROUTE=640,TGRP= 4,ODR=300,LAUTH=1,LATTR=RERTEINT; 

ADD-LDAT:LROUTE=640,TGRP=4,ODR=400,LAUTH=1; 

CHANGE-LPROF:PROFIDX=3,SRCGRP=40,LRTE=340; 

CHANGE-LPROF:PROFIDX=4,SRCGRP=40,LRTE=640; 

CHANGE-LPROF:PROFIDX=5,SRCGRP=40,LRTE=440; 

ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LAUTH=1, 
LDP=0-W-00-49-40-2889-X,PROFIDX=4;

If another virtual node were to be added in a new country, for example Austria, then the following measures are required:

Configure the virtual node number as OWNNODE.
If the station numbers do not correspond to an existing DPLN group, you may need to configure a new DPLN group. (In our example we expand the DPLN to include five-digit station numbers.)
The new virtual node must be configured with the AMO KNDEF.
The new subscribers must be configured.
The subscribers must then be assigned the LCR profile if this is not already specified by the hardware configuration. (In our example, two source groups are required because the location is large and is distributed over 2 APs.)
Configure the trunk group with the trunks for this node.
Expansion of LCR level 1:
- For every new city, a new outdial rule must be configured with the number 1xx for the company in Austria.
- This outdial rule must be assigned to the LCR route with the LRTE number of the outdial rule.
- The new LRTE must be assigned to LCR profile 1 for both source groups.
- A new outdial rule with the number 2xx must be configured for the new country, Austria.
- This outdial rule should be assigned to the LCR route with the LRTE number of the outdial rule.
- The new LRTE is to be assigned to LCR profile 2 with both source groups.

Expansion of LCR level 2:

A new LTRE must be configured for this source group for all LCR routes from LTRE 3xx onwards (in our example LTRE 3xx to 6xx).
Existing LCR profiles greater than or equal to 3 (3 to 5 in our example) must be expanded to include the new source group.
Two new LCR profiles must be configured for the destination Austria, Profile 6 for reroute internal and Profile 7 for direct breakout to the central office.
The new station number must be assigned LCR profile 6 for internal destinations in Germany.
External station numbers in Austria must be assigned LCR profile 7.

Example:

The system is expanded to include two IPDA shelves at the Prater site. The APs are assigned the LTU numbers 42 and 43. This is why they are assigned source groups 42 and 43. The virtual node number is 1-1-3 with the node code 93. The ISDN station number is +43 5 1707 – X.

ADD-WABE:CD=93,DAR=OWNNODE,CHECK=N; 

ADD-WABE:CD=20000&&39999,DPLN=3,DAR=STN; 

ADD-KNDEF:NNO=1-1-3,TYPE=OWN, ISDNCC=43,ISDNAC=5,ISDNLC=1707,
ISDNSK=4, NODECD=93,NODECDSK=2,DPLN=3,ADPLN=3; 

ADD-SBCSU:STNO=9420100,OPT=OPTI,CONN=DIR, PEN=1-42-3-0,DVCFIG=OPTIIP,
COS1=1,COS2=1,LCOSV1=1, LCOSV2=1,LCOSD1=1,LCOSD2=1,DPLN=3; 

ADD-SBCSU:STNO=9430100,OPT=OPTI,CONN=DIR, PEN=1-43-3-0,DVCFIG=OPTIIP,
COS1=1,COS2=1,LCOSV1=1, LCOSV2=1,LCOSD1=1,LCOSD2=1,DPLN=3; 

CHANGE SDAT is omitted because in this case the source group is already 
assigned to the PEN via the AMO UCSU. Luckily, neither of the APs contains an 
additional virtual node :-) 

ADD-BUEND:TGRP=2,NAME="BDL AP42 KN1-1-3",NO=30; ADD-BUEND:TGRP=3,
NAME="BDL AP43 KN1-1-3",NO=30; 

ADD-TDCSU:OPT=NEW,PEN=1-42-1-0,COTNO=20,COPNO=20,DPLN=0,ITR=0,COS=1,LCOSV=1,
LCOSD=1,CCT="CO Vienna 192",DESTNO=92,PROTVAR=EDSAUT,SEGMENT=1,ATNTYP=CO,ISDNIP=00,
ISDNNP=0,TRACOUNT=8,NNO=1-1-192,TGRP=2,SRCHMODE=ASC,INS=Y,DEV=S2COD,BCHAN=1&&30,
BCNEG=Y,BCGR=1,LWPAR=1, SRCGRP=42; 

ADD-TDCSU:OPT=NEW,PEN=1-43-1-0,COTNO=20,COPNO=20,DPLN=0,ITR=0,COS=1,LCOSV=1,
LCOSD=1,CCT="CO Vienna 193",DESTNO=93,PROTVAR=EDSAUT,SEGMENT=1,ATNTYP=CO,
ISDNIP=00,ISDNNP=0,TRACOUNT=8,NNO=1-1-193,TGRP=3,SRCHMODE=ASC,INS=Y,DEV=S2COD,
BCHAN=1&&30,BCNEG=Y,BCGR=1,LWPAR=1, SRCGRP=43; 

ADD-LODR:ODR=104,CMD=OUTPULSE,DGTS=000435; 
ADD-LODR:ODR=104,CMD=ECHO,FIELD=3; 
ADD-LODR:ODR=104,CMD=NPI,NPI=ISDN,TON=INTERNAT; 
ADD-LODR:ODR=104,CMD=END; ADD-LODR:ODR=104,INFO="LODR for Company in Austria"; 

ADD-RICHT:MODE=LRTENEW,LRTE= 104,LSVC=ALL, NAME="SRC Company in Austria",TGRP=3,DNNO=1-1-193; 

ADD-LDAT:LROUTE=104,TGRP= 3,ODR=104,LAUTH=1,LATTR=RERTEINT; 

CHANGE-LPROF:PROFIDX=1,SRCGRP=42,LRTE=104; 
CHANGE-LPROF:PROFIDX=1,SRCGRP=43,LRTE=104; 
ADD-LODR:ODR=201,CMD=OUTPULSE,DGTS=00043; 
ADD-LODR:ODR=201,CMD=ECHO,FIELD=3; 
ADD-LODR:ODR=201,CMD=NPI,NPI=ISDN,TON=INTERNAT; 
ADD-LODR:ODR=201,CMD=END; ADD-LODR:ODR=201,INFO="LODR FOR Austria"; 
ADD-RICHT:MODE=LRTENEW,LRTE= 201,LSVC=ALL, NAME="Austria",TGRP=3,DNNO=1-1-193; 
ADD-LDAT:LROUTE=201,TGRP= 3,ODR=201,LAUTH=1,LATTR=RERTEINT; 

CHANGE-LPROF:PROFIDX=1,SRCGRP=42,LRTE=201; 
CHANGE-LPROF:PROFIDX=1,SRCGRP=43,LRTE=201; 

ADD-RICHT:MODE=LRTENEW,LRTE=342,LSVC=ALL,NAME="SRC42 INTERNAT",TGRP=2,DNNO=1-1-192; 
ADD-RICHT:MODE=LRTENEW,LRTE=343,LSVC=ALL,NAME="SRC43 INTERNAT",TGRP=3,DNNO=1-1-193; 

ADD-LDAT:LROUTE=342,TGRP=2,ODR=300,LAUTH=1; ADD-LDAT:LROUTE=343,TGRP=3,ODR=300,LAUTH=1; 
ADD-RICHT:MODE=LRTENEW,LRTE=442,LSVC=ALL, ,NAME="SRC42 INLAND",TGRP=2,DNNO=1-1-192; 
ADD-RICHT:MODE=LRTENEW,LRTE=443,LSVC=ALL,,NAME="SRC43 INLAND",TGRP=3,DNNO=1-1-193; 

ADD-LDAT:LROUTE=442,TGRP=2,ODR=400,LAUTH=1; ADD-LDAT:LROUTE=443,TGRP=3,ODR=400,LAUTH=1; 

ADD-RICHT:MODE=LRTENEW,LRTE=542,LSVC=ALL,NAME="SRC42 RERT INT",TGRP=2,DNNO=1-1-192; 
ADD-RICHT:MODE=LRTENEW,LRTE=543,LSVC=ALL,NAME="SRC43 RERT INT",TGRP=3,DNNO=1-1-193;  

ADD-LDAT:LROUTE=542,TGRP= 2,ODR=300,LAUTH=1,LATTR=RERTEINT; 
ADD-LDAT:LROUTE=542,TGRP=2,ODR=300,LAUTH=1; 
ADD-LDAT:LROUTE=543,TGRP= 3,ODR=300,LAUTH=1,LATTR=RERTEINT; 
ADD-LDAT:LROUTE=543,TGRP=3,ODR=300,LAUTH=1; 

ADD-RICHT:MODE=LRTENEW,LRTE=642,LSVC=ALL,NAME="SRC42 RERT NAT",TGRP= 2,DNNO=1-1-192; 
ADD-RICHT:MODE=LRTENEW,LRTE=643,LSVC=ALL,NAME="SRC43 RERT NAT",TGRP=3,DNNO=1-1-193;  

ADD-LDAT:LROUTE=642,TGRP= 2,ODR=300,LAUTH=1,LATTR=RERTEINT; 
ADD-LDAT:LROUTE=642,TGRP=2,ODR=400,LAUTH=1; 
ADD-LDAT:LROUTE=643,TGRP= 3,ODR=300,LAUTH=1,LATTR=RERTEINT; 
ADD-LDAT:LROUTE=643,TGRP=3,ODR=400,LAUTH=1; 

CHANGE-LPROF:PROFIDX=3,SRCGRP=42,LRTE=342; 
CHANGE-LPROF:PROFIDX=3,SRCGRP=43,LRTE=343; 
CHANGE-LPROF:PROFIDX=4,SRCGRP=42,LRTE=542; 
CHANGE-LPROF:PROFIDX=4,SRCGRP=43,LRTE=542; 
CHANGE-LPROF:PROFIDX=5,SRCGRP=42,LRTE=342; 
CHANGE-LPROF:PROFIDX=5,SRCGRP=43,LRTE=343; 

ADD-LPROF:PROFNAME="RERT AUSTRIA", SRCGRP=1,LRTE= 501,PROFIDX=6; 
CHANGE-LPROF:PROFIDX=6,SRCGRP=2,LRTE=502; CHANGE-LPROF:PROFIDX=6,SRCGRP=17,LRTE=517; 
CHANGE-LPROF:PROFIDX=6,SRCGRP=26,LRTE=526; CHANGE-LPROF:PROFIDX=6,SRCGRP=40,LRTE=540; 
CHANGE-LPROF:PROFIDX=6,SRCGRP=42,LRTE=642; CHANGE-LPROF:PROFIDX=6,SRCGRP=43,LRTE=643; 

ADD-LPROF:PROFNAME="CO AUSTRIA", SRCGRP=1,LRTE= 301,PROFIDX=7; 
CHANGE-LPROF:PROFIDX=7,SRCGRP=2,LRTE=302; CHANGE-LPROF:PROFIDX=7,SRCGRP=17,LRTE=317; 
CHANGE-LPROF:PROFIDX=7,SRCGRP=26,LRTE=326; CHANGE-LPROF:PROFIDX=7,SRCGRP=40,LRTE=340; 
CHANGE-LPROF:PROFIDX=7,SRCGRP=42,LRTE=442; CHANGE-LPROF:PROFIDX=7,SRCGRP=43,LRTE=443; 

ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LAUTH=1, LDP=0-W-00-43-5-1707-X,PROFIDX=6; 

ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LAUTH=1, LDP=0-W-00-43-X,PROFIDX=7;

A separate description will be created for the topic of networking.

${DocTitle}, ID: ${DocID}

© 03/2026 Mitel Networks Corporation. All rights reserved. Mitel and the Mitel logo are trademark(s) of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH & Co. KG. All other trademarks herein are the property of their respective owners.