166.3 Parameter Description

ALARMNO	Alarm number of logical device class (Alarm must have been assigned with AMO VADSU, ANTYPE=DIR or ANTYPE=PERS before) >> refer to Feature Usage Example Alarm Message Administration << *** only relevant if OPTISET, OPTIP500, OPTIIP, ANADEV, BASE, SET600, S0PP or S2PP specified for DVCFIG ***
	Type of Input	:	Single value, optional
	Possible values	:	0 (no alarm assigned) 8 - 583
	Default Value	:	0
APICLASS	API Protocol Class >> refer to Feature Usage Example Workstation Protocol << *** only relevant if API specified for DVCFIG ***
	Type of Input	:	Single value, optional
	Possible values	:	TS	= Protocol CorNet-TS
			TSX	= Protocol CorNet-TS X-Messages
			WP	= Protocol CorNet-WP
			WPPLUS	= Protocol CorNet-WP+
	Default Value	:	TS
APMOBUSR	Mobile User activation via application >> refer to FeatureUsage Example Smart Card Application << *** only relevant if OPTIP500, OPTIIP specified for DVCFIG ***
	Type of Input	:	Single value, optional
	Possible values	:	Y	= Mobile User activation via application
			N	= Mobile User activation via CP
	Default Value	:	N
APPM	Station with identity application module *** only relevant if OPTIP500 specified for DVCFIG ***
	Type of Input	:	Single value, optional
	Possible values	:	Y, N
	Default Value	:	N
ASYNCT	Timer for short synch losses *** only relevant for modules SLC16, SLMO , SLMO (FCTID=1) , SLMQ (only Q2153-X), SLMQ3, STMA (FCTID=4), STMI-HFA (FCTID=3) and STMI2-HFA (FCTID=3) ***
	Type of Input	:	Single value, optional
	Possible values	:	10 - 2530 (internally always rounded to tens)
	Default Value	:	500
	Note	:	This parameter is intended for test purposes only - therefore, the default value specified should not be changed for no reason
	Note	:	Download of changed value to the module must be initiated by deactivation/activation of corresponding circuit either by using parameter OFFTYPE or via AMO DSSU.
AUTHREQ	Authentication required *** only relevant for STMI2-IGW (SIP subscriber) ***
	Type of Input	:	Single value, optional
	Possible values	:	Y N
	Default Value	:	N
BASICSVC	Basic Service Default Value for devices with NI-BRI protocol *** only relevant if SET600, DTE, FAX, MSN specified for DVCFIG ***
	Type of Input	:	Single value, optional
	Possible values	:	SPEECH	= Speech
			AUDIO3K1	= 3.1 kHz Audio
			UDI64	= 64 kbps Unrestricted Digital Information
			UDI64RA	= 64 kbps Unrestricted Digital Information (Rate-Adapted)
BLF	Busy lamp field
	Type of Input	:	Single value, optional
	Possible values	:	N	no
			NO	no
			Y	yes
			YES	yes
CALLOG	Device with callog >> refer to Feature Usage Example Call log for optiset E / optiPoint << *** only relevant if OPTISET, OPTIP500, OPTIIP ***
	Type of Input	:	Single value, optional
	Possible values		NONE	= no callog
			ALL	= callog recording all incoming calls as well as all outgoing calls
			TRIES	= callog recording all incoming call tries as well as all outgoing calls
	Default Value	:	NONE
CBKBMAX	Maximum number of call backs to this station in the busy condition *** only relevant if SET600, S0PP, S2PP, DTE, FAX, MSN *** *** only relevant if RCBKB=N *********************************************
	Type of Input	:	Single Value, optional
	Possible values	:	1 - 5
			99 (no limit)
	Default Value	:	5
	Note	:	If RCBKB=Y is also specified or already assigned, CBKBMAX is ignored (ADD, CHANGE) and CBKBMAX=0 is displayed (DISPLAY) or CBKBMAX is not regenerated (REGENERATE)
			When entering RCBKB=N without simultaneous specification of CBKBMAX, the default value CBKBMAX=5 is assigned (ADD, CHANGE)
CBKNAMB	Automatic callback on no answer is stored in the mailbox *** only effective for DIGITEs with display (see parameter DIGNODIS) and mailbox *** *** see also parameter RCBKNA ***
	Type of Input	:	Single Value, optional
	Possible values		Y	= Automatic callback on no answer is stored in the mailbox
			N	= Automatic callback on no answer is carried out after the handset has been lifted/replaced
	Default Value		Y
CLNTDESK	Desk number for UFIP client *** only relevant for STMI2-IGW (SIP subscriber) ***
	Type of input	:	Single value, optional
	Possible values	:	0 - 999999999999
	Default value	:	empty string
COMGRP	Com Group the device is allowed to access *** only relevant if OPTISET, OPTIP500, OPTIIP specified for DVCFIG ***
	Type of Input	:	Single value, optional
	Possible values	:	0	= no Com Group assigned
			1- 1024	= valid Com Group assigned
	Default Value	:	0
CONN	Device connection type
	Type of Input	:	Single Value, mandatory (ADD)
			Single Value, optional (DISPLAY)
	Possible values	:	DIR, EXT, PNT, ATMPSW, SIP, IP2
			DIR	= direct connection
			EXT	= off-premises/external station connection
			PNT	= connection via PNT (S0 bus) or UCON (OPTISET / OPTIP500)
			ATMPSW	= ATM connection (Port Switching)
			IP2	= connection via IP (HFA Gateway Version# 2)
			SIP	= connection via IP (SIP)
	Default Value	:	Subscriber search will not be restricted to a specific CONN value (DISPLAY)
COSNO	Number of sought class of service
	Type of Input	:	Single Value, chained single values (max.2) and ranges, optional
	Possible values	:	1 - 1000
	Default Value	:	Subscriber search will not be restricted to a specific COSNO value (DISPLAY)
COSX	Class of service switchover group >> refer to Feature Usage Example Class of Service Switchover COSX <<
	Type of Input	:	Single Value, optional
	Possible values	:	0 - 15
	Default Value	:	0
COS1 COS2	Class of service 1 (AMO COSSU, TYPE=COS) Class of service 2 (AMO COSSU, TYPE=COS)
	Type of Input	:	Single Value, mandatory (ADD) Single Value, optional (CHANGE)
	Possible values	:	1 - 1000
DCFWBUSY	Delayed Call Forwarding - On Busy *** only relevant if OPTISET, OPTIP500, OPTIIP specified for DVCFIG ***
	Type of Input	:	Single value, optional
	Possible values	:	Y
			N
	Default Value	:	N
DELPBOOK	Delete CMI Phonebook When deleting a CMI subscriber, the associated Phonebook is deleted too. This can be avoided by specifying DELPBOOK=NO, eg. when deleting and newly creating a subscriber at a different PEN.
	Type of Input	:	Single value, optional
	Possible values	:	Y
			N
	Default Value	:	Y
DEV	Device type
	Type of Input	:	Single value, optional
	Possible values	:	OPTISET, OPTIP500, OPTIIP, SET600, ANADEV, BASE, RADIO, VIRTDTE, EXTLINE, API, ANADTE, ANAFAX, DTE, FAX, MSN
	Default Value	:	Subscriber search will not be restricted to a specific DEV value (DISPLAY)
	(see also parameter DVCFIG)
DFSVCANA	Default service of the analog terminal for outgoing calls >> refer to Feature Usage Example optiset E and Analog Terminals << >> refer to Feature Usage Example optiPoint Up0E and Analog Terminals << >> refer to Feature Usage Example optiPoint IP and Analog Terminals << *** only relevant if ANADEV ***
	Type of Input	:	Single value, optional
	Possible values	:	VCE, FAX, DTE
	Default Value	:	VCE
DIGNODIS	Digite with no display *** only relevant if OPTISET, OPTIP500, OPTIIP, BASE, RADIO or CMIADM specified for DVCFIG ***
	Type of Input	:	Single value, optional
	Possible values	:	Y	= Terminal without Display
			N	= Terminal with Display
	Default Value	:	N
	Note	:	If the terminal is designated as "without Display" (although physically available), absolutely all displays are suppressed (such as call number, name of caller, etc.) and system-side acknowledgements are only signalled via acoustic acknowledgement If the terminal is designated as "with Display" (although not physically available), system-side acknowledgements are no longer signalled acoustically
DNIDSP	Display DNIS/SIDANI information for incoming calls with DNIS routing
	Type of Input	:	Single value, optional
	Possible values	:	Y	= display of available DNIS / SIDANI information
			N	= no display of DNIS / SIDANI information
	Default Value	:	N
DOPTIDX	Index into option table (AMO ZAND) for functional data device (DTE) >> refer to Feature Usage Example EURO-ISDN Terminals << >> refer to Feature Usage Example National ISDN Basic Rate Interface (NI BRI) <<
	Type of Input	:	Single value, optional
	Possible values	:	1-10
	Default Value	:	1
DPLN	Feature access group, dial plan group >> refer to Feature Usage Example Customer Groups, Shared Systems CUG <<
	Type of Input	:	Single value, optional
	Possible values	:	0 - 15
	Default Value	:	0
DPROT	Protocol variant for functional data device (DTE) >> refer to Feature Usage Example EURO-ISDN Terminals << >> refer to Feature Usage Example National ISDN Basic Rate Interface (NI BRI) <<
	Type of Input	:	Single Value, optional (depends on DVCFIG, see above)
	Possible values	:	SBDSS1	= EURO ISDN protocol DSS1
			SBEDSR1	= EURO-ISDN Protocol EDSS1 RESERVE 1
			SBEDSR2	= EURO-ISDN Protocol EDSS1 RESERVE 2
			SBEDSR3	= EURO-ISDN Protocol EDSS1 RESERVE 3
			SBEDSR4	= EURO-ISDN Protocol EDSS1 RESERVE 4
			SBNIBRI	= Telcordia Technologies NI-BRI Protocol (National ISDN Basic Rate Interface)
	Note	:	The protocol type parameters SPROT, DPROT and FPROT are optional. However, an xPROT parameter must be specified if a terminal type to which it refers is configured. Values specified for the protocol type parameters are ignored if the appropriate terminal does not exist under the station number specified

Table 5

Recommended combination(s) of protocol variants (xPROT) and Option index (xOPTIDX) for functional terminal devices on the S0-Bus *** For functional S0/S2 point-to-point connections, see Parameter PROT ***

xPROT=   (x=S, D, F)	DVCFIG= SET600   SOPT=	DVCFIG=... &DTE   DOPT=	DVCFIG=... &FAX   FOPT=
SBDSS1	10	10	10
SBNIBRI	7	7	7
SBEDSR1 : SBEDSR4	-	-	-

DSSTNA	Alert tone if calling station in a voice call connection (see AMO ZAND, CP=CMALTONE and AMO DTIM1, parameter VCHATONE, VCHAPAU) *** only relevant if OPTISET, OPTIP500, OPTIIP, BASE, RADIO or CMIADM specified for DVCFIG ***
	Type of Input	:	Single value, optional
	Possible values	:	Y	= call monitoring alerting tone at calling station
			N	= no call monitoring alerting tone at calling station
	Default Value	:	N
DSSTNB	Alert tone if called station in a voice call connection (see AMO ZAND, CP=CMALTONE and AMO DTIM1, parameter VCHATONE, VCHAPAU) *** only relevant if OPTISET, OPTIP500, OPTIIP, BASE, RADIO or CMIADM specified for DVCFIG ***
	Type of Input	:	Single value, optional
	Possible values	:	Y	= call monitoring alerting tone at called station
			N	= no call monitoring alerting tone at called station
	Default Value	:	Y
DTMFCTRD	Device controlled by incoming DTMF signalling
	Type of Input	:	Single value, optiona
	Possible values	:	Y	= device controlled by incoming DTMF signalling
			N	= device cannot be controlled by DTMF signalling
			YES	= device controlled by incoming DTMF signalling
			NO	= device cannot be controlled by DTMF signalling
	Default Value	:	N
DTMFBLK	Block hearing of incoming DTMF tones while in conference *** only relevant if OPTISET, OPTIP500, OPTIIP, SET600, ANADEV specified for DVCFIG ***
	Type of Input	:	Single value, optional
	Possible values	:	Y	= Hearing of incoming DTMF tones will be blocked while in conference
			N	= Hearing of incoming DTMF tones will not be blocked while in conference
	Default Value	:	N
DVCFIG	Device configuration
	Type of Input	:	Single Value, chained single values (max. 3), mandatory
	Possible values	:	OPTISET	= Digital voice terminal OPTISET (S0 / CorNet-TS)
			OPTIP500	= Digital voice terminal OPTIP500 (S0 / CorNet-TS)
			OPTIIP	= Digital IP voice terminal (IP / CorNet-TS)
			SET600	= Digital voice terminal SET600 (S0 / funct.protocol)
			BASE 1)	= CMI base station (Up0/E / CorNet-TS)
			RADIO 1)	= CMI mobile user (Up0/E / CorNet-TS)
			EXTLINE 1)	= CMI extension connection (S0 / funct. protocol)
			ANADEV	= analog terminal, all services
			API	= Workstation protocol interface, DTE service (S0 / CorNet-WP)
			ANADTE	= analog terminal, DTE service
			ANAFAX	= analog terminal, FAX service
			DTE	= Terminal or terminal adapter, DTE service (S0 / funct. protocol)
			FAX	= Terminal or terminal adapter, FAX service (S0 / funct. protocol)
			S0PP	= S0 point-to-point conn., 2 b-channels (S0 / funct. protocol)
			S2PP	= S2 point-to-point conn., 30 b-channels (S2 / funct. protocol)
			VIRTDTE	= virtual dte for software download
	1)	:	Only certain circuits of the SLC16 module can be used for this terminal (see Chapter 166 Point "3. CMI configuration ( CMI version >= V3.0 )" )

Table 6

Terminal configuration assignments to the line modules

*1 : only if DVCFIG=CMIADM has been previously set up with OPT=CMI .
*2 : only if DVCFIG=BASE has been previously set up with OPT=CMI .
*3 : only if DVCFIG=RADIO has been previously set up with OPT=CMI.

OPT	CONN	Terminal configuration	Module
FBUS	PNT DIR EXT	SET600 &[FAX] &[DTE] SET600 &[FAX] &[DTE] SET600 &[FAX] &[DTE]	SLMQ SLMS,STMD STMD
OPTI	DIR PNT PNT ATMPSW IP IP2	[OPTISET/OPTIP500] &[FAX] &[DTE/API] & [ANAFAX / ANADTE] [OPTISET/OPTIP500] &[FAX] &[DTE/API] & [ANAFAX / ANADTE] [OPTISET/OPTIP500] [OPTISET/OPTIP500] &[FAX] &[DTE/API] & [ANAFAX / ANADTE] OPTIIP OPTIIP & [API] & [ANAFAX / ANADTE]	SLMO (FCTID=1), SLMQ-EXT SLMQ3 STMA (FCTID=4) STMI-HFA STMI2-HFA
CMI		CMIADM BASE EXTLINE & [FAX] & [DTE] RADIO & [FAX] & [DTE]	SLC16 SLC16 SLC16 SLC16
OPTIEXP	(DIR, PNT) (DIR, PNT) (DIR, PNT) (ATMPSW) (ATMPSW) (IP2)	[OPTISET/OPTIP500] &[FAX] &[DTE/API] SET600 &[FAX] &[DTE] ANADEV [OPTISET/OPTIP500] &[FAX] &[DTE/API] SET600 &[FAX] &[DTE] ANADEV	except SLMQ3 STMA (FCTID=4) STMA (FCTID=4) STMI2-HFA
CMIEXP		CMIADM BASE RADIO	*1 *2 *3
FPP	PNT DIR EXT DIR EXT	S0PP S0PP S0PP S2PP S2PP	SLMQ SLMS,STMD STMD DIU-N2, DIU-N4, DIU-S2 DIU-N2, DIU-N4, DIU-S2

EXTBUS	Extended Bus - Bus Operating Range for SLMS/STMD > 150m *** only relevant for modules SLMS and STMD (all versions) ***
	Type of Input	:	Single value, optional
	Possible values	:	Y	Distance between first and last termina <= 35m, thus range between module and last terminal > 150m is possible
			N	Distance between first and last terminal > 35m, but distance between module and last terminal < 150m
	Default Value	:	N	(CONN=EXT)
			Y	else
	Note	:	Download of changed value to the module must be initiated by deactivation/activation of corresponding circuit either by using parameter OFFTYPE or via AMO DSSU.
FIXEDIP	Fixed IP address *** only relevant for STMI2-IGW (SIP subscriber) ***
	Type of Input	:	Single value, optional
	Possible values	:	Y N
	Default Value	:	N
FLASH	Flash controlled functions support *** only relevant if ANADEV specified for DVCFIG ***
	Type of Input	:	Single value, optional
	Possible values	:	Y	= Flash controlled functions allowed
			N	= Flash controlled functions not allowed
	Default Value	:	Y
FOPTIDX	Index into option table (AMO ZAND) for functional facsimile device (FAX) >>see parameter DOPTIDX for description<<
FPROT	Protocol variant for functional facsimile device (FAX) >>see parameter DPROT for description<<
	Type of input:		single value, optional
	Possible values:		SBDSS1	protocol variant dss1
			SBEDSR1	protocol variant edss1 reserve 1
			SBEDSR2	protocol variant edss1 reserve 2
			SBEDSR3	protocol variant edss1 reserve 3
			SBEDSR4	protocol variant edss1 reserve 4
			SBNIBRI	protocol variant ni bri
HEADSET	Terminal with headset *** only relevant if OPTISET, OPTIP500, OPTIIP *** *** see also parameter HSKEY ***
	Type of Input	:	Single value, optional
	Possible values	:	N	= No headset
			NOIND	= headset without hardware indication (i.e. plugging/unplugging is n o t recog- nized by the hardware - must be made known by pressing the headset key)
			WITHIND	= headset with hardware indication (plugging/unplugging is recognized by the hardware -> headset key not required)
	Default Value	:	N
HMUSIC	Number of Music on Hold recording (recorder must have been assigned with AMO RCSU, RECAPL=HMUSIC, OPMODE=CONT, OPTYPE=RANDOM before)
	Type of Input	:	Single value, optional
	Possible values	:	0 (System Music on Hold assigned) 1 - 150
	Default Value	:	0
HSKEY	Functioning of the HS key (if present) *** only relevant if OPTISET, OPTIP500, OPTIIP *** *** see also parameter HEADSET ***
	Type of Input	:	Single value, optional
	Possible values	:	NORMAL	= HS key serves to answer, initiate or terminate a call
			HSIND	= HS key serves as an indication whether headset without hardware indication is plugged or not
	Default Value	:	NORMAL
IDCR	Station with identity card reader *** only relevant if OPTISET, OPTIP500, OPTIIP specified for DVCFIG ***
	Type of Input	:	Single value, optional
	Possible values	:	Y, N
	Default Value	:	N
INS	Station(s) in service ?
	Type of Input	:	Single value, optional
	Possible values	:	Y, N
			Y	= The station terminals will be released for call processing.
			N	= The station terminals are not put into service (data pre-assigned).
			SIGNOFF	= The station terminals have not (yet) been assigned a LOCATION (signed-off subscribers)
	Default Value	:	Y (ADD)
			Subscriber search will not be restricted to a specific DEV value (DISPLAY)
IPADDR	IP address *** only relevant for STMI2-IGW (SIP subscriber) ***
	Type of Input	:	4 values, concatenated with ".", optional
	Possible values	:	0-255
	Default Value	:	0.0.0.0
IPCODEC	Codec Type for IP Phone for bandwidth calculation in RESMAN >> refer to Feature Usage Example HiPath Feature Access << *** only relevant for modules STMI-HFA (FCTID=3), STMI2-HFA (FCTID=3), STMI2-IGW (SIP subscriber) ***
	Type of Input	:	Single value, optional
	Possible values	:	G711	= G711 always to be used
			G711PREF	= G711 preferably to be used
			G723	= G723 always to be used
			G723PREF	= G723 preferably to be used
			G729A	= G729A always to be used
			G729APREF	= G729A preferably to be used
	Default Value	:	G723PREF	(CONN=IP)
			G711PREF	(CONN=IP2)
IPPASSW	Password for IP LOGON procedure >> refer to Feature Usage Example HiPath Feature Access << *** only relevant for modules STMI-HFA (FCTID=3), STMI2-HFA (FCTID=3) ***
	Type of Input	:	Single value, optional
	Possible values	:	NONE	= No password defined
			text, 6 - 20 alpha numerical characters	= valid password
	Default Value	:	NONE
	Note	:	Download of changed value to the module must be initiated by deactivation/activation of corresponding circuit either by using parameter OFFTYPE or via AMO DSSU.
ITR	Internal traffic restriction group >> refer to Feature Usage Example Customer Groups, Shared Systems CUG <<
	Type of Input	:	Single value, optional
	Possible values	:	0 - 15
	Default Value	:	0
KEYSYS	Subscriber configured as a keysystem (AMO KCSU) >> refer to Feature Usage Example Integrated Key Functionality Multi-line Access <<
	Type of Input	:	Single value, optional
	Possible values	:	Y, N
	Default Value	:	Subscriber search will not be restricted to a specific KEYSYS value (DISPLAY)
LCOSD	LCR class of service (data)
	Type of Input	:	Single Value, chained single values (max.2) and ranges, optional
	Possible values	:	1 - 1000
	Default Value	:	Subscriber search will not be restricted to a specific LCOSD value (DISPLAY)
LCOSD1 LCOSD2	LCR class of service 1 (data - see AMO COSSU, TYPE=LCOSD) LCR class of service 2 (data - see AMO COSSU, TYPE=LCOSD) >> refer to Feature Usage Example LCR (Least Cost Routing) <<
	Type of Input	:	Single value, required
	Possible values	:	1 - 1000
LCOSV	LCR class of service (voice)
	Type of Input	:	Single Value, chained single values (max.2) and ranges, optional
	Possible values	:	1 - 1000
	Default Value	:	Subscriber search will not be restricted to a specific LCOSV value (DISPLAY)
LCOSV1 LCOSV2	LCR class of service 1 (voice - see AMO COSSU, TYPE=LCOSV) LCR class of service 2 (voice - see AMO COSSU, TYPE=LCOSV) >> refer to Feature Usage Example LCR (Least Cost Routing) <<
	Type of Input	:	Single value, required
	Possible values	:	1 - 1000
LWPAR	Loadware Parameter Block (AMO LWPAR, TYPE=DIUS2) *** only relevant for modules DIU-N2, DIU-N4, DIU-S2 ***
	Type of Input	:	Single value, optional
	Possible values	:	0 - 9
	Default Value	:	0
	Note	:	Download of changed value to the module must be initiated by deactivation/activation of corresponding circuit either by using parameter OFFTYPE or via AMO DSSU.
MAINO	Main station number of a bus configuration
	Type of Input	:	Single Value, mandatory
	Possible values	:	0 - 999999999999
	Note	:	The station number must be assigned as the main station number of an OPTI, CMI or S0/S2 point-to-point configuration.
NEWNO	New station number
	Type of Input	:	Single Value, optional
	Possible values	:	0 - 999999999999
	Note	:	The station number must be present in the dialing plan.
	Note	:	For OPTIIP only : Download of changed value to the module must be initiated by deactivation/activation of corresponding circuit either by using parameter OFFTYPE or via AMO DSSU.
OFFTYPE	Type of deactivation order (controls both station deactivation and loading of circuit data)
	Type of Input	:	Single value, optional
	Possible values	:	NL	= no locking
			DC	= deactivate with camp-on
			DI	= deactivate immediately
	Default Value	:	DC
			DI (signed-off subscriber, MSN station number))
	Note	:	After CHANGE command is executed, the station is switched back to the original dependability state (different to AMO DSSU handling). However OFFTYPE only takes effect in combination with other parameters for which deactivation or downloading makes sense.
OPT	Specification of bus type or unit to be expanded for an existing station number (branch parameter)
	Type of Input	:	Single Value, mandatory
	Possible values	:	FBUS, OPTI, OPTIEXP,CMI, FPP, SVC, MSN (ADD) FBUS, OPTI, CMI, FPP (CHANGE)
	FBUS	= Functional bus
	OPTI	=	OPTISET configuration (ADD: install main station number of OPTISET configuration)
	CMI	=	CMI configuration (ADD: Add main station number for administration user, base station, mobile user, extension connection of the CMI configuration)
	OPTIEXP	=	Add analog, functional or CorNet-TS terminals at an OPTISET configuration for a secondary station number
	CMIEXP	=	no longer used with CMI V3.0 (Add another administration user, base station or mobile user at a CMI configuration under a secondary station number)
	FPP	= Functional S0/S2 point-to-point connection (ADD: assign main station number of functional point-to-point connection)
	SVC	= Expand the service allocation and terminal configuration of a station on a CorNet point-to-point connection or bus connection
	MSN	=	Add MSN station number at FBUS / OPTI / FPP configuration or an MSN secondary station number at OPTISET configuration.
OPTICA	Optiset E control adapter for connecting a PC dialer >> refer to Feature Usage Example optiset E with Data Adapter << *** only relevant if OPTISET specified for DVCFIG ***
	Type of Input	:	Single value, optional
	Possible values	:	0 - 2
	Default Value	:	0
OPTICOM	Optiset E with ComManager connection *** only relevant if OPTISET, OPTIP500, OPTIIP specified for DVCFIG ***
	Type of Input	:	Single value, optional
	Possible values	:	Y, N
	Default Value	:	N
OPTIDA	Optiset E data adapter / data plus adapter for connecting a data terminal >> refer to Feature Usage Example optiset E with Data Adapter << *** only relevant if OPTISET specified for DVCFIG ***
	Type of Input	:	Single value, optional
	Possible values	:	0 - 2
	Default Value	:	0
OPTIDX	Index into option table (AMO ZAND) for functional point-to-point connect. >> refer to Feature Usage Example Adding an S2 station <<
	Type of Input	:	Single value, optional
	Possible values	:	1-10
	Default Value	:	1
OSMO	UFIP IS TO BECOME OSMO CLIENT
	Type of Input		Single value, optional
	Possible values		Y, N , YES, NO
PASSWD	Password for SIP subscriber *** only relevant for STMI2-IGW (SIP subscriber) ***
	Type of Input	:	Single value, optional
	Possible values	:	text, up to 20 alpha numerical characters
	Default Value	:	empty string
PATTERN	Idle code pattern for the B-channels >>refer to "Hicom 300/300 E/300 H ATM Connectivity Phase 1 to 3"<< *** only relevant for module STMA (FCTID=4) ***
	Type of Input	:	Single value, optional
	Possible values	:	0 - 255
	Default Value	:	213 ( = H’D5 )
	Note	:	Download of changed value to the module must be initiated by deactivation/activation of corresponding circuit either by using parameter OFFTYPE or via AMO DSSU.
PEN	Port equipment number of the station: LTG-LTU-SLOT-CCT
	Type of Input	:	Single value, optional
	Possible values	:	g-uu-sss-ccc
			g	= LTG Number 1 (no other value)
			uu	= LTU Number 1 - 15 in HHS (Host Shelf) 16 not defined 17 - 99 in AP (Access Point Shelf)
			sss	= Slot number 1 - 121
			ccc	= Circuit number 0 - 254
	Note	:	A suitable module must be configured for the slot addressed by PEN (AMO BCSU)
			The possible LTU and Slot values for PEN depend on the systems architecture and can be found in the BCSU AMO description.
			The possible Circuit values depend on the module type and its functionality. They can be listed using DISP-BCSU: TYPE=PEN [,LTG= , LTU= , SLOT= , CCT= ] ; which will also output the actual PEN status (e.g. NOT CONNECTED)
PERMACT	Layers 1 and 2 permanently active ? *** only relevant if SET600, S0PP or S2PP specified for DVCFIG ***
	Type of Input	:	Single value, optional
	Possible values	:	Y	= permanently active
			N	= not permanently active
	Default Value	:	Y
	Note	:	CorNet-T-terminals must be permanently active. This means, since this parameter must be set for each circuit, that it is only relevant for functional bus connections.
	Note	:	Download of changed value to the module must be initiated by deactivation/activation of corresponding circuit either by using parameter OFFTYPE or via AMO DSSU.
PMIDX	External Voice Mail Server Index
	Type of Input	:	Single value, optional
	Possible values	:	0
			1- 99
	Default Value	:	0
PROT	Protocol type for functional point-to-point connection >>refer to Feature Usage Example Adding an S2 station <<
	Type of Input	:	Single Value, mandatory (ADD) Single Value, optional (CHANGE)
	Possible values	:	SBDSS1	= EURO ISDN protocol DSS1
			SBEDSR1	= EURO-ISDN Protocol EDSS1 RESERVE 1
			SBEDSR2	= EURO-ISDN Protocol EDSS1 RESERVE 2
			SBEDSR3	= EURO-ISDN Protocol EDSS1 RESERVE 3
			SBEDSR4	= EURO-ISDN Protocol EDSS1 RESERVE 4

Table 7

Recommended combination of protocol variants (PROT) and Option index (OPTIDX) for functional S0/S2 point-to-point connections *** For functional terminal devices on the S0-Bus, see Parameter DPROT ***

PROT=	DVCFIG= S0PP   OPT=	DVCFIG= S2PP   OPT=
SBDSS1	9	9
SBEDSR1 : SBEDSR4	-	-

RCBKB	Reject call back on busy *** see also parameter CBKBMAX ***
	Type of Input	:	Single Value, optional
	Possible values	:	Y	= No call back option possible for this subscriber on busy
			N	= Call back option possible for this subscriber on busy
	Default Value	:	N
RCBKNA	Reject call back on no answer *** only effective for DIGITEs without mailbox *** *** see also parameter CBKNAMB ***
	Type of Input	:	Single Value, optional
	Possible values	:	Y	= No call back option possible for this subscriber on no answer
			N	= Call back option possible for this subscriber on no answer
	Default Value	:	N
REP	No. of add-on devices (e.g. repertory key terminal) *** only relevant if OPTISET, OPTIP500, OPTIIP, BASE, RADIO or CMIADM specified for DVCFIG ***
	Type of Input	:	Single Value, optional
	Possible values	:	0 - 2 (OPTIP500)
		:	0 - 4 (OPTISET / BASE / RADIO / CMIADM ))
	Default Value	:	0 (no add-on devices available)
SECAPPL	Smart Card Access Application ID >> refer to FeatureUsage Example Smart Card Application << *** only relevant if OPTIP500 or OPTIIP specified for DVCFIG ***
	Type of Input	:	Single value, optional
	Possible values	:	0	= no Smart Card Access Application ID assigned
			1- 999	= valid Smart Card Access Application ID assigned
	Default Value	:	0
SECR	Digite is to become secretary in an executive/secretary system >> refer to FeatureUsage Example CHESE Integrated Exec./Sec. System << *** only relevant if OPTISET, OPTIP500, OPTIIP specified for DVCFIG ***
	Type of Input	:	Single Value, optional
	Possible values	:	Y, N
	Default Value	:	N
	Note	:	When the value is changed, the relevant terminal must first be switched off (either by using parameter OFFTYPE or via AMO DSSU) because the value must not be changed while the terminal is operating.
SECZON	Security zone for UFIP *** only relevant for STMI2-IGW (SIP subscriber) ***
	Type of Input	:	Single value, optional
	Possible values	:	text, up to 20 alpha numerical characters
	Default Value	:	empty string
SECZONE	Security zone *** only relevant for STMI2-IGW (SIP subscriber) ***
	Type of Input	:	Single value, optional
	Possible values	:	text, up to 20 alpha numerical characters
	Default Value	:	empty string
SMGSUB	SMG subscriber *** only relevant for STMI2-IGW (SIP subscriber) ***
	Type of Input	:	Single value, optional
	Possible values	:	Y N
	Default Value	:	N
SOPTIDX	Index into option table (AMO ZAND) for voice/speech device S0 *** only relevant if SET600 or EXTLINE specified for DVCFIG *** >>see parameter DOPTIDX for description<<
	Default Value	:	1 (SET600) 6 (EXTLINE)
SPDC1	Central speed calling list 1 >> refer to Feature Usage Example Speed Dialling <<
	Type of Input	:	Single Value, optional
	Possible values	:	0 - 15	(assign SPDC1 list)
			16	(no SPDC1)
	Default Value	:	no SPDC1
SPDC2	Central speed calling list 2 >> refer to Feature Usage Example Speed Dialling <<
	Type of Input	:	Single Value, optional
	Possible values	:	0 - 15	(assign SPDC1 list)
			16	(no SPDC2)
	Default Value	:	no SPDC2
SPDI	Station with speed calling individual
	Type of Input	:	Single Value, optional
	Possible values	:	0, 10, 20, 30
	Default Value	:	0
SPROT	Protocol variant for functional voice/speech device *** only relevant if SET600 or EXTLINE specified for DVCFIG *** >>see parameter DPROT for description<<
	Default Value	:	SBQ9311 (EXTLINE)
SRCGRP	Source group index
	Type of Input		1 to 2 single values, concatenated with "&"
			optional
	Possible values		1 - 255
SSTNO	Secret station number *** not relevant for SIP subscribers *** >> refer to Feature Usage Example CLIR Calling Line Ident. Restriction <<
	Type of Input	:	Single Value, optional
	Possible values	:	Y	= The user’s station number does not appear on the called party’s display (internal and external)
			N	= The user’s station number does appear on the called party’s display (internal and external)
			ONLYEXT	= The user’s station number does not appear on the external station’s display. Instead, a replacement number (configured by AMO KNMAT) is displayed
			ONLYEX0	= Neither the user’s station number nor a replacement calling number is displayed at the external station’s display
	Default Value	:	N
STD	Number of key layout/map standard >> refer to Feature Usage Example Key Layout Standards << *** only relevant if OPTISET, OPTIP500, OPTIIP, BASE, RADIO or CMIADM specified for DVCFIG ***
	Type of Input	:	Single Value, optional
	Possible values	:	0 - 255
	Default Value	:	0
STNO	Station number The devices specified under DVCFIG are assigned to this STNO
	Type of Input	:	Single values and ranges, mandatory (ADD, CHANGE, DELETE) optional (DISPLAY, REGENERATE)
	Possible values	:	0 - 999999999999
	Note	:	The station number must be present in the dialing plan.
			When entering ranges, please ensure that the second number is always the higher one and that both numbers have the same length.
			A maximum of 600 station numbers may be included in a range.
	ADD, OPT=FBUS / OPTI / CMI: CHANGE, DELETE, DISPLAY, REGENERATE:
		a maximum of 10 value entries is allowed, e.g. 5 ranges or 3 ranges and 4 single values.
	ADD, OPT=OPTIEXP:
		A maximum of two station numbers can be set up via the OPTISET configuration (as specified with parameter MAINO). An OPTISET configuration may contain a maximum of three terminals, with all functional terminals counting collectively as one terminal.
	ADD, OPT=CMIEXP:
		A maximum of 1 station number is permissible which can still be set up on the CMI configuration (specified with parameter MAINO). It should also be borne in mind that a CMI configuration may not contain more than 2 terminals
	DELETE, CHANGE: The station number must have been installed.
	DISPLAY, REGENERATE:
		If TLNNU is not entered, all subscribers that have been installed by AMO SBCSU are output.
	DELETE, CHANGE: The station number must have been installed.
	DISPLAY, REGENERATE:
		If TLNNU is not entered, all subscribers that have been installed by AMO SBCSU are output.
SUBIPADD	IP address for UFIP *** only relevant for STMI2-IGW (SIP subscriber) ***
	Type of Input	:	4 values, concatenated with ".", optional
	Possible values	:	0 - 255
	Default value	:	0.0.0.0
SVC	Specification of service to be deleted
	Type of Input	:	chained single values, mandatory
	Possible values	:	FAX	= Delete FAX device
			DTE	= Delete DTE device
			MSN	= Delete MSN station number/ MSN secondary station number
			ALL	= Delete all associated devices
TEXTSEL	Text selector for selecting the language for the display >> refer to Feature Usage Example Multilingual User Interface << *** only relevant if OPTISET, OPTIP500, OPTIIP or RADIO specified for DVCFIG ***
	Type of Input	:	Single Value, optional
	Possible Values		american	american english
			BRAZIL	brazilian
			catalan	catalan
			CHINESE	Chinese (only if OPTISET/ OPTIP500)
			croatian	croatian
			czech	czech
			danish	danish
			dutch	dutch
			english	english
			estonIAN	estonian
			finnish	finnish
			french	french
			GERMAN	german
			GERNOUML	german without umlauts
			greek	greek
			hungary	hungarian
			indones	indonesian
			italian	italian
			JPN	Japanese (only if OPTISET/ OPTIP500)
			LATVIAN	latvian
			LITHUAN	lithuanian
			malay	malayan
			norweg	norwegian
			polish	polish
			portug	portuguese
			romanian	romanian
			russCYR	russian (cyrillic characters)
			russLAT	russian (latin characters)
			serbcyr	serbian (cyrillic characters)
			serblat	serbian (latin characters)
			slovak	slovakian
			slowen	slowenian
			spanish	spanish
			swedish	swedish
			thai	thai
			TURKISH	turkish
	Default Value		Preset system language (see AMO ZAND, parameter TEXTSEL, 1st value)
TRACE	Malicious call trace allowed >> refer to Feature Usage Example TRACE Malicious Call Tracing <<
	Type of Input	:	Single Value, optional
	Possible values	:	Y, N
	Default Value	:	Subscriber search will not be restricted to a specific TRACE value (DISPLAY)
TSI	Terminal Selection Identifier
	Type of Input	:	chained single values (max. 3), optional
	Possible values	:	0	(automatic TSI allocation via AMO)
			1 - 8	(valid TSI number)
	Default Value	:	0	(automatic TSI allocation via AMO)
	Note	:	The allocation of TSI numbers to terminals depends on the sequence in which the values for TSI and DVCFIG are entered.
TYPE	Desired station configuration options
	Type of Input	:	Single Value, optional
	Possible values	:	TERMDATA	Display all terminal data for terminals assigned with SBCSU
			BUS	Bus configuration with location (PEN), terminals, STNO and TSI
			BUSDATA	Combination of BUS and TERMDATA per station number
			FPP	Output all S0/S2 point-to-point connections (including all MSN links defined)
			MSN	Output all MSN links, i.e. stations configured with DVCFIG=MSN
			OPTIDAT	Individual OPTISET / OPTIP500 / OPTIIP terminal data and hardware settings
			SEARCH	Output all subscribers matching the search criteria(s) as specified by the optional parameters CONN, DEV, COSNO, LCOSV, LCOSD, TRACE, KEYSYS, INS
	Default Value	:	TERMDATA
USERID	User ID *** only relevant for STMI2-IGW (SIP subscriber) ***
	Type of Input	:	Single value, optional
	Possible values	:	text, up to 20 alpha numerical characters
	Default Value	:	empty string
USRID	User ID for UFIP *** only relevant for STMI2-IGW (SIP subscriber) ***
	Type of Input	:	Single value, optional
	Possible values	:	text, up to 20 alpha numerical characters
	Default Value	:	empty string
VCI	Virtual Connection Identifier >>refer to "Hicom 300/300 E/300 H ATM Connectivity Phase 1 to 3"<< *** only relevant for module STMA (FCTID=4) ***
	Type of Input	:	Single Value, optional
	Possible values	:	0 - 65535
	Note	:	Download of changed value to the module must be initiated by deactivation/activation of corresponding circuit either by using parameter OFFTYP or via AMO DSSU.
VPI	Virtual Path Identifier >>refer to "Hicom 300/300 E/300 H ATM Connectivity Phase 1 to 3"<< *** only relevant for module STMA (FCTID=4) ***
	Type of Input	:	Single Value, optional
	Possible values	:	0 - 7
	Note	:	Download of changed value to the module must be initiated by deactivation/activation of corresponding circuit either by using parameter OFFTYP or via AMO DSSU.