168.3 Parameter Description


ACKST	Acknowledgement variants between DPI and DPS (DPS = DP center-controlled connection setup) only for ANATE (for effects and logistics of these values see AMO DAPPL)
	Type of Input	:	Single value, chained single values
	Possible values	:	CHR = Acknowledgement variant between DPI and announcement device TE = Delayed connection acknowledgment to to DPI after end of announcement

ALARMNO	Alarm number of logical device class (Alarm must have been assigned with AMO-VADSU, ANTYPE=PERS (for 520-583) or ANTYPE=DIR (for 8 -519) before)
	Type of Input	:	Single value, optional
	Possible values	:	0 (no alarm assigned) 8 - 583
	Default value	:	0

ATTR	Station Attribute
	Input type	:	Single value, mandatory
	Possible values	:	SIGNOFF	= Signed Off Station(s)
			VARDIAL	= Station(s) with Variable Dialing Type Recognition
			FLOAT	= Display only floating stations
			ACLSTN	= ACL support stations

CCTIDX	Index into timer block table for SLMA1/SLMA2/SLMA3/SLMA24/SLMAB/SLMAR/SLMAC circuit (see AMO PTIME, TYPE=SLMA1 for the times to be set).
	Input type	:	Single value, optional
	Possible values	:	0 - 16
	Default value	:	16 (null value)

CMIND	Authorizations or features for a station, which are to be deleted.
	Type of Input	:	Single value Chained single values, mandatory
	Possible values	:	SSTN	= Special station (cannot be released automatically)
			SPDC1,2	= Central speed dialing lists
			ALL	= All station
			CHR	= Start of announcement following 1st call charge pulse
			TE	= Delayed connection acknowledgement to DPA after end of announcment
			DHPAR	= Station with supplementary dialing
			SUFDIAL	= Station can suffix dial
			WITNS	= Station/port for connection of tape recorder sign
			SOD	= Special Outpulsing Device: Special Device (e.g. Interactive Voice Recorder) which gets informations via DTMF outpulsing
			VCEPAGE	= Voice Pager

COFIDX	Index of a data block with which the SICOFI (Codec and Filter) must be loaded on an SLMA.
	Input type	:	Single value, optional
	Possible values	:	0	= Data block for Germany
			1	= Data block for Austria
			2	= Data block for Australia
			3	= Data block for Spain and Belgium (L <= 2x250 Ohm)
			4	= Data block for Spain and Belgium (L <= 2x250 Ohm)
			The default value to be assigned for Spain and Belgium is 4.
			5	Not allowed on 4K.
			6	Support of old analog phones using ground key for consultation
			7	reserved for future use
	Default value	:	0

CONN	Connection type of device * PEN specific, not for fictitious stations *
	Type of Input	:	Single value, optional, group member (MIN=1) for CHANGE, mandatory for DISPLAY
	Possible Values	:	DIR	Direct connection * not for TMDNH board *
			OPST1	Off premises connection via T1 span * only for ANATE at TMDNH board * * not for ANATECM *
			OPSSLMA	Off premises connection via SLMA * only for ANATE at SLMA/1/2/3/24/B/R board * * not for ANATECM *
	Default Value		DIR	for ADD at non TMDNH board
			OPST1	for ADD at TMDNH board

COS1 COS2	Class of Service 1 Class of Service 2
	Input type	:	Single value, mandatory
	Possible values	:	1 - 1000

COSNO	Class of Service
	Input type	:	Single value, mandatory
	Possible values	:	1 - 1000

COSX	COS changeover group
	Input type	:	Single value, optional
	Possible values	:	0 - 15
	Default Value	:	0

COTRACE	Malicious call tracing of CO calls
	Input type	:	Single value, optional
	Possible values	:	YES, NO
	Default Value	:	NO

DHPAR	Device handler parameter for station with supplementary dialing * not for DVCFIG=ANATECM *
	Input type	:	chained single values, optional
	Possible values	:	for connection of an external Voice Mail-System ( SPEC = SUFDIAL ) :
			PREDIA	= predialog with external server
			ASEND	= send A-party number
			BSEND	= send B-party number
			DTMFST	= DTMF codes to an external device
			RING1	= only 1 ring per ring variant (SLMA1/2/3/24/B/R)

			for COMTEL3 terminals ( SPEC /= SUFDIAL) :

			LEDSIGN	= Analog station with LED-Signalling
			MWLED	= Station with Message Waiting LED (Thailand)
			VMSDP	= Analog station with VMS controlling capability
			FLASH	= Analog station with function keys incorporating flash (Consultation is done before the A, B, C, D tone is transmitted, i.e. the signal key need not be pressed prior to the function key. The user must not wait for dial tone after initiating consultation.)

DIAL	Dialing methods for analog devices
	Input type	:	Single value, optional
	Possible values	:	DP	= Dial pulsing (for rotary dialing or dial pulsing push-button telephone)
			DTMF	= Dual tone multi-frequency signals (push-button telephones only)
			VAR	= Variable Dialing Type Recognition (DP or DTMF are identified automatically) Advisory: VAR must not be assigned to Comtel Terminals (is not checked by AMO).)
	Default Value	:	DP	= for SLMA/SLMAR-Board
			VAR	= for SLMA1/SLMA2/SLMA3/SLMA24/ SLMAB-Board, signed off and floating stations

DPLN	Dial plan group (digit analysis result allocation)
	Input type	:	Single value, mandatory
	Possible values	:	0 - 15

	Default Value	:	YES

DTMFBLK	Block / unblock hearing of incoming DTMF tones in conference
	Type of Input	:	Single value, optional, group member (MIN=1) for CHANGE
	Possible Values	:	YES,Y	Incoming DTMF tones are blocked from hearing while in conference
			NO,N	DTMF tones are not blocked from hearing while in conference
	Default Value		N

DVCFIG	Device combination
	Input type	:	Single value, chained single values, mandatory
	Possible values	:	ANATE	= Analog voice terminal
			ANATECM	= Analog voice terminal with charge metering
			AUXDIGI	= Auxiliary DIGI260 for HTC and ViNet
			FAX	= FAX device (analog interface)
			DTEANA	= Data terminal (analog interface)

Permitted device combinations (DVCFIG) of a subscriber to the modules (the sequence of the devices in a combination is as desired).

Table 8

Sequence of Devices in a Combination

DEVICE COMBINATION

MODULE

ANATE

SLMA/1/2/3/24/B/R/C (1) TMDNH

ANATE

FAX

SLMA/1/2/3/24/B/R/C (1) TMDNH

ANATE

DTEANA

SLMA/1/2/3/24/B/R/C (1) TMDNH

ANATECM

SLMAR

AUXDIGI

SLMB, SLMB4

(1) Means: SLMA, SLMA1, SLMA2, SLMA3, SLMA24, SLMAB, SLMAR or SLMAC, note that the SLMAR board is skipped for free PEN search.


FLASH	Enable / Disable Flash controlled functions for ANATEs (e.g. Hookflash)
	Type of Input	:	Single value, optional, group member (MIN=1) for CHANGE
	Possible Values	:	YES,Y	Flash funcions enabled (e.g. Hookflash)
			NO,N	Flash funcions disabled (e.g. Hookflash)
	Default Value		Y

HMUSIC	Number of music on hold recording (AMO-RCSU)
	Input type	:	Single value, optional
	Possible values	:	0 - 150
	Default Value	:	0

INS	Station(s) in service ?
	Input type	:	Single value, optional
	Possible values	:	YES	= The assigned station is to be enabled. Individual terminals can remain blocked by specifying the corresponding (x)BL parameter.
			NO	= The assigned station is not to be enabled (data is only provided in advance).
			FLOAT	= This is for ’floating’ ID card users, as opposed to stations with a specific device configuration. This floating station is not enabled by means of this parameter.
			SIGNOFF	= The assigned station is added to the system in a signed off state.
			ACLSTN	= ACL support station. This station is handled like a floating station without a physical port.
	Default Value	:	YES

ITR	Internal traffic restriction / closed user group
	Input type	:	Single value, mandatory
	Possible values	:	0 - 15

LCOSD	LCR-CLASS-OF-SERVICE for DTE ( see AMO-COSSU, TYPE=LCOSD )
	Input type	:	Single value, required
	Possible values	:	1 - 1000	valid LCOSD number

LCOSD1 LCOSD2	LCR-CLASS-OF-SERVICE-1 for DTE ( see AMO-COSSU, TYPE=LCOSD ) LCR-CLASS-OF-SERVICE-2 for DTE ( see AMO-COSSU, TYPE=LCOSD )
	Input type	:	Single value, required
	Possible values	:	1 - 1000	valid LCOSD number

LCOSV	LCR-CLASS-OF-SERVICE for Voice, Fax, Btx, Ttx ( see AMO-COSSU, TYPE=LCOSV )
	Input type	:	Single value, required
	Possible values		1 - 1000	valid LCOSV number

LCOSV1 LCOSV2	LCR-CLASS-OF-SERVICE-1 for Voice, Fax, Btx, Ttx ( see AMO-COSSU, TYPE=LCOSV ) LCR-CLASS-OF-SERVICE-2 for Voice, Fax, Btx, Ttx ( see AMO-COSSU, TYPE=LCOSV )
	Input type	:	Single value, required
	Possible values	:	1 - 1000	valid LCOSV number

NEONMWI	Neon lamp for message waiting indication
	Input type	:	Single value, 34th parameter of a min-1-group
	Input type	:	Single value, optional
	Possible values	:	NO	no
		:	YES	yes

NEWNO	New station number (STNO) to be assigned.
	Input type	:	Single value, optional
	Possible values	:	The station number must exist in the dial plan (AMO WABE). Only 1 single value between 0 and 999999 is permissible).
	Note	:	If the STNO to be changed has been declared as a a single value, then NEWNO changes the old station number to the new one. If a range has been entered for the parameter STNO, the NEWNO value is used as the first station number in the new range. If there are gaps in the STNO range (stations not created), these gaps are included in the new range.

OFFTYPE	Type of deactivation order controls both station locking and circuit data loading
	Input type	:	Single value, optional
	Possible values	:	NL	= no lock, no downloading of circuit data
			DC	= deactivate with camp-on (soft lock)
			DI	= deactivate immediately (hard lock)
	Default Value	:	DC
	Note	:	After CHANGE command is executed, the station is switched back to the original dependability state (different to AMO DSSU handling). However OFFTYPE only takes effect in combination with other parameters for which locking or downloading makes sense.

PEN	Port equipment number of a station (LTG-LTU-SLOT-CCT)
	Type of Input	:	Single value, optional
	Possible values	:	g-uu-sss-ccc
			g	= LTG Number: 1 (no other value)
			uu	= LTU Number: 1 - 15 in HHS (Host Shelf) 16 not defined 17 - 99 in AP (Access Point Shelf)
			sss	= Slot Number: 1 - 121
			ccc	= Circuit Number: 0 - 254
	Default Value	:		First suitable PEN for a station creation
	A suitable module must be configured for the slot addressed by PEN (AMO BCSU) The possible LTU and Slot values for PEN depend on the systems architecture and can be found in the BCSU AMO description. The possible Circuit values depend on the module type and its functionality. They can be listed using DISP-BCSU: TYPE=PEN [,LTG= , LTU= , SLOT= , CCT= ] ; which will also output the actual PEN status (e.g. NOT CONNECTED).

PMIDX	Phone mail server index
	Input type	:	Single value, 33rd parameter of a min-1-group
	Input type	:	Single value, optional
	Possible values	:	numeric, 0-99

PULSLEV	Level of charge metering pulses (only effective for SLMAR board)
	This parameter is mandatory for adding a station with DVCFIG=ANATECM. If it is missing, it will be prompted.
	Input type	:	Single value, optional
	Possible values	:	VEFF3	3 V r.m.s. (effective voltage)
			VEFF5	5 V r.m.s. (effective voltage)

PULSTYPE	Type of charge metering pulses (only effective for SLMAR board)
	This parameter is mandatory for adding a station with DVCFIG=ANATECM. If it is missing, it will be prompted.
	Input type	:	Single value, optional
	Possible values	:	KHZ12	12 kHz charge pulses
			KHZ16	16 kHz charge pulses
			POL	Static polarity reversal
			POL12	Static polarity reversal + 12 kHz
			POL16	Static polarity reversal + 16 kHz
			FORM	Pulse form reversal

RCBKB	Reject call back on busy
	Input type	:	Single value, optional
	Possible values	:	YES, NO
	Default value	:	NO

RCBKNA	Reject call back on no answer (will not work on stations with mailbox classmark)
	Input type	:	Single value, optional
	Possible values	:	YES, NO
	Default value	:	NO

SPDC1	Central speed dialing list 1
	Input type	:	Single value, optional
	Possible values	:	0-15
	Default value	:	No Central speed dialing list 1

SPDC2	Central speed dialing list 2
	Input type	:	Single value, optional
	Possible values	:	0 - 15
	Default value	:	No Central speed dialing list 2

SPDI	Individual speed dialing
	Input type	:	Single value, optional
	Possible values	:	0, 10, 20, 30
	Default value	:	0 (means no individual speed dialing)

SPEC	Special station equipment * not for DVCFIG=ANATECM and AUXDIGI *
	Input type	:	chained Single value, optional
	Possible values	:	SSTN	= Station has special equipment
			(For stations without clear-channel capability, the parameter DVCFIG must be set to ANATE). - Recorded announcement - Loudspeaker - Dictation equipment - Entrance telephone system - Night watchman service - Code call access
			SUFDIAL	= Station can suffix dial (see paramet DHPAR)
			WITNS	= Stn/port for connection of tape rec. etc. as witness
			SOD	= Special Outpulsing Device: Special Device (e.g. Interactive Voice Recorder) which gets informations via DTMF outpulsing (Cross Reference to AMO ZAND, Parameter TYPEDNIS)
			VCEPAGE	= Voice Pager

SSTNO	Secret station number
	Input type	:	Single value, optional
	Possible values	:	YES	= The user’s station number does not appear on the called party’s display (internal and external)
			NO	= The user’s station number does appear on the called party’s display (internal and external)
			ONLYEXT	= The user’s station number does not appear on the external station’s display. Instead, a replacement number (configured by AMO KNMAT) is displayed
			ONLYEX0	= Neither the user’s station number nor a replacement calling number is displayed at the external station’s display.
	Default value	:	NO

STNO	Station call number
	Input type	:	Single value, chained single values, range, mandatory
	Possible values	:	0 - 999999; Station number must exist in DPLN (AMO WABE).
	(ADD)		Max. 10 values are permissible, e.g., 5 ranges or 3 ranges and 4 single values
	(CHANGE )		Max. 2 values are permissible, either a single value or a range, but not 2 single values.
	(DISPLAY )		If the parameter STNO is missing in the DISPLAY command, all stations (STNO-MIN to STNO-MAX) are output. Otherwise, as for ADD-SCSU.
	(DELETE )		See ADD.
(REGENERATE)			See ADD.
	Note	:	When specifying a range, value 2 must be greater than value 1 and must have the same number of digits. A range must not include more than 600 station numbers. The range restriction of 600 subscribers applies only to the functions ADD, CHANGE and DELETE.

STNTYPE	Station hardware
	Input type	:	Single value, mandatory
	Possible values	:	SSTN	= Station with special equipment (e.g., clear-channel capability)
			DP	= Dial pulsing (rotary dialing)
			DTMF	= Dual tone multi-frequency (pushbutton)
			WITNS	= Station for connection of tape recorder as witness
			WITKEY	= Station with connect witness key
			ANATECM	= Station with charge metering equipment
			SOD	= Special Outpulsing Device: Special Device (e.g. Interactive Voice Recorder) which gets informations via DTMF outpulsing
			VCEPAGE	= Voice Pager

TEXTSEL	Text selector of Display Language * only for AUXDIGI) *
	Type of Input	:	single value, optional
	Possible Values		american	american english
			BRAZIL	brazilian
			catalan	catalan
			croatian	croatian
			czech	czech
			danish	danish
			dutch	dutch
			english	english
			estonIAN	estonian
			finnish	finnish
			french	french
			GERMAN	german
			greek	greek
			hungary	hungarian
			indones	indonesian
			italian	italian
			malay	malayan
			norweg	norwegian
			polish	polish
			portug	portuguese
			romanian	romanian
			russCYR	russian cyrillic characters
			russLAT	russian latin characters
			slovak	slovakian
			sloven	slovenian
			spanish	spanish
			swedish	swedish
			thai	thai
			TURKISH	turkish
	Default Value		system language (see AMO ZAND, parameter TEXTSEL, 1. value)

TYPE	Branch parameter (output options)
	Input type	:	Single value, optional
	Possible values	:	ALL	= Output all station information.
			ATTR	= Output all stations with a specific attribute described in parameter ATTR.
			COS	= Output all stations which have the class of service specified in the parameter COSNO.
			HW	= ’Telephone-based’ selection for output. i.e. telephone equipment as specified with the STNTYPE parameter following.
			LCOSV	= Output all stations which have the LCR class of service for VOICE specified in the parameter LCOSV.
			LCOSD	= Output all stations which have the LCR class of service for DTE specified in the parameter LCOSD.
			CONN	= Stations with specific connection type
	Default value	:	ALL

${DocTitle}, ID: ${DocID}

© 02/2025 Mitel Networks Corporation. - All rights reserved.
Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG.
All other trademarks herein are the property of their respective owners.