202.4.2 Advisories

 
H03:
ADD DATA FOR <bbb> <xxxx> WITH AMO CONSY
H04:
DELETE DATA FOR <bbb> <xxxx> WITH AMO CONSY
H06:
THE EXISTING OVERLAY CONFIGURATION WAS <action>
H07:
<aaa> <xxxx> DELETED
H08:
LTG <xx> ADDED (NL)
H09:
THE NEW OVERLAY CONFIGURATION HAS BEEN ASSIGNED. PLEASE MOUNT THE
HWY-CABLE OF OVERLAY LTU <xx> TO STANDARD LTU <xx>.
THE NEW OVERLAY HWYS CAN BE CHECKED VIA AMO TSU IN THE SAME WAY AS
THE NORMAL HWYS FOR STANDARD LTUS.
H09:
THE NEW OVERLAY CONFIGURATION HAS BEEN ASSIGNED.
THE NEW OVERLAY HWYS CAN BE CHECKED VIA AMO TSU IN THE SAME WAY AS
THE NORMAL HWYS FOR STANDARD LTUS.
H10:
<aaa> <xxxx> ALREADY DELETED
H11:
THE STATUS OF AT LEAST ONE OVERLAY HWY IS DEFECT.
PLEASE INITIATE A HARDRESTART OF THE SWU AFTER SAVING THE CHANGED
CONFIGURATION VIA AMO UPDAT.
H12:
THE AP SPECIFIC TONE AND ANNOUNCEMENT PARAMETERS HAVE TO BE LOADED MANUALLY. THIS CAN BE DONE BY MEANS OF COMMAND EXEC-USSU:NCUILOAD NOTE: CHANGES OF CP TONES MAY WORK IMMEDIATELY, BUT MANUAL LOADING IS STILL REQUIRED.
H13:
THE ACTUAL LTUC BOARD HAS <xx> MOUNTED CBM MODULES BUT FOR ONLY <xx> MODULES
CONFIGURATION VALUES HAVE BEEN SPECIFIED. THE REMAINING MODULES WILL BE
CONFIGURED WITH DEFAULT VALUE EC64.
H15:
PARAMETER APRTADDR CAN NOT BE CHECKED FOR A PLAUSIBLE VALUE.
THIS CHECK WILL BE DONE LATER WITHIN AMO-APRT.
H16:
PARAMETER <param> IGNORED
H17:
PARAMETER <param> HAS NOT BEEN SPECIFIED, THEREFORE THE
DEFAULT ROUTER ADDRESS <ip1.ip2.ip3.ip4> HAS BEEN ASSIGNED.
H18:
THE CHANGE TAKES EFFECT NOT BEFORE THE AFFECTED NCUI BOARD IS RESTARTED
(EXEC-USSU:MODE=UPDATAP)
H19:
NO CONFIGURED DATA FOUND FOR ENTERED VALUE(S).
H20:
THE AMOUNT OF AVAILABLE B-CHANNELS ON NCUI/NCUI2 BOARD HAS BEEN CHANGED !
PLEASE CHECK THE CONFIGURATION (ALSO AMO-STMIB)
H21:
IF THE PARAMETER BCHLCNT IS SPECIFIED, THE AMOUNT OF AVAILABLE B-CHANNELS
ON NCUI/NCUI2 BOARD IS SMALLER AS THE DEFAULT VALUE OF THE BOARD !
THE RESOURCE MANAGEMENT IS ALSO AFFECTED BY SPECIFIYING THIS
PARAMETER, THEREFORE ONLY <xxx> B-CHANNELS WILL BE CONFIGURED.
H22:
SPE NOT ACTIVATED, NO SPE RESULT STATE INFORMATION AVAILABLE.
H23:
SINCE PAYLOAD ENCRPTION AND/OR DMC IS ENABLED, THE NUMBER OF B-CHANNELS
HAS BEEN REDUCED BY @@@ B-CHANNELS DUE TO HIGH PERFORMANCE NEEDS.
H24:
THE SETTING OF PARAMETER BITRATE HAS BEEN CHANGED TO 100MBFD
BECAUSE OF HW RELATED RESTRICTIONS. CHANGE POSSIBLE WITH AMO-STMIB.
H25:
THE PARAMETERS SOCOTYPE, IPMODE, DHCPV4 AND DHCPV6 ARE NOT RELEVANT FOR
TRADITIONAL HW SHELVES AND WILL BE IGNORED.
H26:
UBGDAT ENTRY HAS BEEN MODIFIED INTERNALLY BEFORE FIRST USAGE.
H27:
SPE ON: TO GET THE SHELF FINALLY INTO SERVICE, FOLLOWING STEPS ARE NEEDED:
-ENTER A MEK VIA THE @@@@@@@@@@@@@@@@@@@@@@
-AFTERWARDS ENTER THIS MEK VIA “MEK Administration Client” (Assistant)
H28:
PLEASE NOTE THAT IPV6 TUNNELING FOR CC<->AP COOMUNICATION
IS NOT FULLY SUPPORTED YET (IN RELEASE 0).
H29:
PLEASE NOTE THAT DHCP FUNCTIONALITY IS NOT FULLY SUPPORTED YET
(IN RELEASE 0).
H30:
Multiple entry of <textsel> has been ignored.
H31:
THE CHANGE TAKES EFFECT NOT BEFORE THE AFFECTED AP SHELF IS
RESTARTED (RES-USSU).
H32:
SOCO50 IS RECOMMENDED FOR VIRTUAL MACHINES WITH ONLY 2 CPU CORES.
SOCO1000 IS RECOMMENDED FOR 4 CPU CORES OR MORE.
SOCO500 IS NO LONGER USED.
H33:
SOCOTYPE AUTOMATICALLY CHANGED TO SOCO1000
${DocTitle}, ID: ${DocID}
 © 02/2025 Mitel Networks Corporation. -  All rights reserved.
 Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG.
 All other trademarks herein are the property of their respective owners.