131.4 Error Messages and Advisories

131.4.1 Error Messages


F01:	LROUTE <xxxx> HAS NOT BEEN DEFINED (AMO RICHT).
F02:	NO LROUT MEMORY LEFT (AMO DIMSU, PARAMETER LROUT)
F03:	ADDING A LRTEL MUST NOT CREATE A GAP NEXT POSSIBLE VALUE = <xxx>.
F04:	LRTEL CANNOT BE APPENDED, BECAUSE LVAL MAX. = <xxx> HAS ALREADY BEEN REACHED.
F05:	LRTEL CANNOT BE INSERTED, BECAUSE LVAL MAX. = <xxx> HAS ALREADY BEEN REACHED.
F06:	TRUNK GROUP <xxx> HAS NOT BEEN DEFINED FOR LROUTE <xxxx> AND THE ENTERED LSVC (AMO RICHT).
F07:	ODR <xxxx> HAS NOT BEEN DEFINED, OR COMMAND SEQUENCE WAS NOT TERMINATED WITH END (AMO LODR).
F08:	LRTEL <xxxx> HAS NOT BEEN SET UP.
F09:	TRUNK GROUP <xxx> HAS NOT BEEN SET UP (AMO BUEND).
F10:	NO LRTEL HAS BEEN SET UP FOR LROUTE <xxxx>.
F11:	KIND=LROUTE MUST BE USED TO DELETE ALL LRTEL FROM LROUTE <xxxx>.
F12:	ATTRIBUTES PRIMRTE AND REROUTE CAN NOT BE SET AT THE SAME TIME CHECK PARAMETER LATTR AGAIN
F13:	THE TRUNK GROUP IS NOT OF THE APPROPRIATE TYPE
F14:	THE CONCATENATED VALUES FOR PARAMETER LSCHED CONFLICT WITH EACH OTHER A TIMEBAND CAN NOT BE DISABLED AND EXPENSIVE AT THE SAME TIME
F15:	LSVC=<xxxx> MUST BE USED, AS THIS ROUTE IS NOT INSTALLED FOR ALL SERVICES
F16:	LSVC=VCE/DTE MUST BE USED, AS THIS ROUTE HAS NOT BEEN INSTALLED FOR ALL SERVICES USING LSVC=ALL
F17:	LSVC=ALL MUST USED, AS THIS ROUTE HAS BEEN INSTALLED FOR ALL SERVICES USING LSVC=ALL
F18:	LSVC=<xxxx> CAN NOT BE USED, AS THIS ROUTE HAS NOT BEEN INSTALLED FOR THIS SERVICES
F19:	PARAMETER CARRIER AND ZONE HAS TO BE ENTERED BOTH IN COMBINATION
F20:	LEVEL<x> OF DNNO MAY NOT EXCEED <xxx>
F22:	LATTR=VOICO MUST NOT BE USED FOR ROUTES WITH LSVC=DTE
F23:	ATTRIBUTES ETEUNVO, ETEMIN0,ETEMIN1, ETEMIN2, ETEMIN3, ETEMINX AND
	ETENORSP CAN NOT BE SET AT THE SAME TIME
	CHECK PARAMETER LATTR AGAIN
F24:	LRTEL @@@@@@@@@@@@@@@ LSVC @@@@ HAS NOT BEEN SET UP
F26:	YOU HAVE NOT ENTERED A PROPER SCCID VALUE. IT SHOULD RANGE BETWEEN [0000,9999) OR '*'
F27:	BEFORE SETTING FX OR TTA TO SVCVCE OR SVCNVCE PARAMETER A NON-NULL VALUE FOR PARAMETER FACILITY MUST BE SET
F28:	DNNO LIKE X-0-Y (X AND Y ARE NOT 0)IS NOT ALLOWED
F29:	DNNO OF LRTEL MUST BE DIFFERENT FROM THE PHYSICAL NODE ID
F30:	FACILITY PARAMETER CAN RANGE BETWEEN 0 AND 99999
F31:	THE VALUE OF SERVICE PARAMETER (LSVC) AND USE OF SVCVCE AND SVCNVCE PARAMETERS SHOULD BE CONSISTENT. SVCVCE CAN BE SET WHEN LSVC IS ALL OR VCE. SVCNVCE CAN BE SET WHEN LSVC IS ALL OR DTE
F32:	THE TRUNKS (AMO-TDCSU) OF LRTEL HAVE OUTWATS AS DEDICATED SERVICE (PARAM DEDSVC) AND LRTEL POINTS TO A NI-2 PRI TRUNK (PARAM PROTVAR). IN THIS CASE YOU MUST ENTER A NON-NULL SCCID VALUE.
F33:	VALUES OUTWATS,WB0..WB9,FX AND TTA FOR SVCVCE(VOICE) AND VALUES OUTWATS, FX AND TTA FOR SVCNVCE(NON-VOICE) CAN NOT BE USED TOGETHER
F34:	THE COT INDEX DOES NOT EXIST. PLEASE CONFIGURE BY MEANS OF AMO-COT FIRST
F35:	FIRST PART (GATEWAY NO) OF PARAMETER ^param^ MUST BE BETWEEN 1 AND 9999
F36:	GATEWAY DATA FOR LRTG =^lrtg^ LRTGEL=^lrtgel^ CAN NOT BE DELETED. DATA FOR BUNDLE AND GATEWAY MAY NOT BE EMPTY AT THE SAME TIME FOR IP-LCR
F37:	BUNDLE AND GATEWAY DATA CAN BE EMPTY AT THE SAME TIME ONLY FOR LATTR VALUES WHICH CONTAIN RERTEINT.
F38:	THE GATEKEEPER IS NOT ACTIVATED IN THE SYSTEM. CONFIGURATION OF GATEWAY ENTRIES GW1..GW5 IS NOT PERMITTED. (CHA-ZANDE: TYPE=ALLDATA, GATEKPR=YES;)
F39:	NO LCR CAN BE DEFINED FOR THIS ROUTE SINCE IT HAS BEEN INSTALLED AS FAX FROM AMO RICHT WHICH IS NOT A VALID SERVICE FOR LCR.

OpenScape 4000 V10, Volume 1: AMO Descriptions, Service Documentation, Issue 5, ID: P31003H31A0S107057620

© 09/2025 Mitel Networks Corporation. - All rights reserved.
Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG. All other trademarks herein are the property of their respective owners.