145.4 Parameter Description


ACKTIM	Acknowledgement timer: timer specifies the period between transmission of a command frame and the expected receipt of the response or acknowledgement. Value is specified in tenth of seconds.
	Type of Input		single value, 7. parameter of a min-1-group
	Possible Values		10-50
	Default Value		10

APCPN	Analogue pstn call priority number
	Type of Input		single value, 3. parameter of a min-1-group
	Possible Values		numeric, 0-16
	Default Value		14

AROB	Automatic redirection on busy
	Type of Input		single value, 5. parameter of a min-1-group
	Possible Values		N
			Y
	Default Value

ATCPN	Analogue trunk call priority number
	Type of Input		single value, 1. parameter of a min-1-group
	Possible Values		numeric, 0-16
	Default Value		12

BCHCONF	DPNSS B Chanel X/Y Configuration
	Type of Input	:	0 to 30 single values, concatenated with & or &&, optional
	Possible Values	:	numeric, 0-30
	Default Value	:

BCHNEG	B Channel Negotiation
	Type of Input	:	single value, optional
	Possible Values	:	N Y	no yes
	Default Value	:	Y

BLNO	Parameter block number
	Type of Input	:	Single value, mandatory (CHANGE)
			Single value or range, optional (DISPLAY)
	Possible Values	:	0 - 200	(TMD circuit type)
			0 - 25	(DIUS2 circuit type)
			0-255	(CDG, DIUS2 circuit type)
			0-49	(CDG circuit type)
			0-78	(NWWTK networking wtk set type)
			1-200	(TMD circuit type)
			1-6	(DIUC modul type)

BLNONEW	New parameter block number
	Type of Input		single value, optional
	Possible Values		numeric, 0-49	COPY, TYPE=CDG
			numeric, 0-9	COPY, TYPE=DIUS2
			numeric, 1-200	COPY, TYPE=TMD

BLNOOLD	Old parameter block number
	Type of Input		single value, mandatory
	Possible Values		numeric, 0-255	TYPE=CDG
			numeric, 0-200	TYPE=TMD

C3CONF	3-party conference hold allowed from conference master.
	Type of Input	:	Single value, 21. parameter of a min-1-group, optional
	Possible Values	:	Y N	Yes No

CABLETYP	type of cable for tmd span
	Type of Input		single value, 2. parameter of a min-1-group
	Possible Values		numeric, 1-7
	Default Value		3


CBG	Call barring group (Realitis DX)
	Type of Input		1 to 8 single values, concatenated with &, optional
	Possible Values		numeric, 0-127

CDG	CDG is connected to DIUS2 (conversion from CORNET to DPNSS1 or DASS2, used in Italy and the UK, for example).
	Type of Input	:	Single value, optional
	Possible Values	:	Y N	Yes No
	Default Value	:	N

CDGCF	CDG Transit Working on Call Forward
	Type of Input	:	single value, optional
	Possible Values	:	Y N	YES NO
	Default Value	:	Y

CDGTYPE	Type of CDG
	Type of Input:		single value, mandatory
	Possible Values	:	CONF TIMER	Configuration parameter Timer and reserve parameter
			MAPPING	Mapping tables HICOM <-> Realitis DX
			CONF2	Configuration - extension for CDG 6.0

CNTRNR	(CouNT Receiver Not Ready) The number of status queries sent to the partner in regard to "receiver not ready" is defined.
	Type of Input	:	Single value, optional
	Possible Values	:	0 - 255
	Default Value	:	255

CONACK	Connect ack sent by protocol handler
	Type of Input	:	Single value, 22. parameter of a min-1-group, optional
	Possible Values	:	N
		:	Y
		:
CONVBN	Conversion back-notify from cornet-n
	Type of Input		single value, 19. parameter of a min-1-group
	Possible Values		N	no
			Y	yes
		:
COPA	Adaptation of diuc to various pcm30 central offices
	Type of Input		single value, 2. parameter of a min-1-group
	Possible Values		CO1G	digital access to tdm central office 1 g
			CO2G	dig. access to tdm central office 2g or tne 2g
			COIT	identifier for l1 error handling
			TNE1A	dig.access to remote equipment 1 g (ver.tne 1a)
			TNE1B	dig.access to remote equipment 1g (ver.tne 1b)
		:	ZERO	basic initialization, no parameters set
		:
COPTYPE	Copper line type
	Type of Input		single value, 10. parameter of a min-1-group
	Possible Values		COAX75	coax 75 Ohm
			STP120	shielded twisted pair 120 Ohm

COS	Class-of-service marks / features
	The values CDRAC, CDRC, and CDRS cannot be linked with NCDR.
	The values EXTEND and PU cannot be linked.
	The values OVR and KN cannot be linked.
	Type of Input	:	maximum of 5 linked single values, optional
	Possible Values	:	CDRAC	Call data registration on attendant console
			CDRC	Central call data registration
			CDRS	Call data registration at station
			NCDR	No call data registration
			EXTEND	Extend
			PU	Pickup
			OVR	Override
			KN	Call waiting
	Default Value	:	NCDR, PU, KN

COS1	EMS/System class-of-service assignment (EMS COS:LOC)
COS2	EMS/System class-of-service assignment (EMS COS:AREA)
COS3	EMS/System class-of-service assignment (EMS COS:NAT)
COS4	EMS/System class-of-service assignment (EMS COS:CONT)
COS5	EMS/System class-of-service assignment (EMS COS:INT)
	for system as a main PABX or satellite PABX TA and RTA are not valid values here, since they have the identical meaning in the system and EMS, and can therefore be passed through.
	Note	:	Overall COS ’CO’ supplements loadware;
			RTA for outward restriction is always set as per the basic DB initialization.
	Type of Input	:	max. 6 linked single values, optional
	Possible Values	:	RTA1:	RESTRICTED TRUNK ACCESS 1
			RTA2:	RESTRICTED TRUNK ACCESS 2
			RTA3:	RESTRICTED TRUNK ACCESS 3
			RTA4:	RESTRICTED TRUNK ACCESS 4
			RTA5:	RESTRICTED TRUNK ACCESS 5
			RTA6:	RESTRICTED TRUNK ACCESS 6
	Default Value	:	RTA1


CRC4C	CRC4 CorNet NQ
	Type of Input	:	Single value, optional
	Possible Values	:	Y N NO
	Default Value	:	N

CRC4REP	Layer-2 CRC4-Reporting
	Type of Input	:	Single value, optional
	Possible Values	:	Y, N
	Default Value	:	N

CRIDC	Carrier Idenfication Code
	Type of Input	:	Single value, optional
	Possible Values	:	0000-9999s
	Default Value	:
	Note	:	mandatory when block is used for CVN
CTYPE	Evaluate digit pre-setting for corresponding existing connection type (incoming) (see parameters DGTPRMS, DGTPRMST, DGTPRMSI) The value N cannot be linked with any other value.
	Type of Input	:	Maximum of 3 linked single values, optional
	Possible Values	:	HOME, CO, TOLL, N
	Default Value	:	N

DASSCPN	DASS call priority number
	Type of Input	:	single value, 4. parameter of a min-1-group, optional
	Possible Values	:	numeric, 0-16
	Default Value	:	13

DASSOPN	DASS operator number
	Type of Input	:	single value, optional
	Possible Values	:	0-9,*,#,A-D, up to 22 characters

DCHAN1	Definition of timeslot for first data channel
	Type of Input	:	Single value, optional
	Possible Values	:	0 - 31 (0= no data channel)
	Default Value	:	16

DCHAN2	ATTENTION: This function has not been implemented!
	Definition of timeslot for a second data channel If DCHAN2>0, DCHAN1 may not be 0. Furthermore, DCHAN1 and DCHAN2 must have different values, except when both parameters have the value 0. The specified DCHAN2 number may not be configured as a device. A second D-channel is useful, for example, if a system user leases from the post office 10 B-channels of an S2-path as nailed connections via local exchanges to a certain remote system and, due to extensive signaling, defines one of these 10 B-channels as a ’private channel’. In both systems, the additional D-channel must be made known using loadware parameters and COT.
	Type of Input	:	Single value, optional
	Possible Values	:	0	(0= no second data channel)
	Default Value	:	0
	Note	:	DCHAN2 may not be 0 if the parameter block is allocated to a circuit which has been assigned a class of trunk (AMO TDCSU, parameter COTNO) in which the circuit parameter PRDC (private D channel; AMO COT, parameter PAR) is specified.
	The speed dialing codes to be pre-set (DGTPR and DGTPRC) are only evaluated if the correct value for parameter SPDCDSS (SPD for DGTPR, SPDC for DGTPRC) has been specified.

DEFID	ROP, default call identity length used in CorNet-NQ
	Type of Input:		single value, optional
	Possible Values		B001	1 digit
			B010	2 digits
			B011	3 digits
			B100	4 digits
	Default Value	:	B010

DEFPASSW	Default password for DPNSS protocol
	Type of Input		single value, optional
	Possible Values		numeric, up to 6 characters

DEV	Kind of device on trunk
	Type of Input		single value, optional (CHANGE)
			single value, optional (ADD/DISPLAY)
	Possible Values		see parameter values DEV in AMOs TDSCU, TACSU, TSCSU
	This parameter indicates for what kind of device the LWPAR block is suitable. All values are accepted, no check is performed. The user is asked to use the right device types.

DGTPR	Speed dialing code to be pre-set for seizure from satellite PABX (valid for SPD 1-15)
	If only one speed dialing code has been assigned in the system, and if both speed dialing codes (DGTPR,DGTPRC) are to be evaluated in accordance with parameter SPDCDSS, DGTPR must be equal to DGTPRC and lead to DAR ’SPDC1’ in the DPLN. If two speed dialing codes have been assigned, DGTPR must lead to DAR ’SPDC2’ in the DPLN.
	Type of Input	:	Single value (up to 6 digits), optional
	Possible Values	:	0 - 9, *, #
	Default Value	:	none

DGTPRC	Speed dialing code (central) to be pre-set for seizure from satellite PABX
	If only one speed dialing code has been assigned in the system, and if both speed dialing codes (DGTPR,DGTPRC) are to be evaluated in accordance with parameter SPDCDSS, DGTPRC must be equal to DGTPR.
	DGTPRC must lead to DAR ’SPDC1’ in the DPLN.
	Type of Input	:	Single value (up to 6 digits), optional
	Possible Values	:	0 - 9, *, #
	Default Value	:	none
The following digit pre-setting parameters DGTPRMS, DGTPRMSI and DGTPRMST are evaluated only if the corresponding parameter value (CO, HOME, TOLL) of the parameter CTYPE is set. The entry ’*’ signifies that no digit pre-setting should be assigned. Pre-set digits are set according to line signal processing of the recorded dial information and handled by call processing as dialed digits.

DGTPRMS	Digit pre-setting after incoming seizure for connection type CO
DGTPRMSI	Digit pre-setting after incoming seizure for connection type HOME or RF_CO
DGTPRMST	Digit pre-setting digit after incoming seizure for connection type TOLL
	Type of Input	:	Single value, optional
	Possible Values	:	0 - 999999 or *
	Default Value	:	*

DLVTIM	Data link verification timer: timer specifies maximum period of link inactivity (no frames exchanged). Value is specified in tenth of seconds.
	Type of Input		single value, 8. parameter of a min-1-group
	Possible Values		50-600
	Default Value		30

DXTG	Realitis DX trunk group Number(s)
	Type of Input		1 to 8 single values, concatenated with &, optional
	Possible Values		numeric, 0-255

DXTGPOS	Position of given DXTG number(s) in TTB table
	Type of Input		1 to 8 single values, concatenated with &, optional
	Possible Values		numeric, 0-31

EDP	Pause between EOD preliminary pulse and recognized dial end
	Type of Input	:	Single value, optional
	Possible Values	:	100 - 450 ms
	Default Value	:	100 ms

EQVIRC	DPNSS Equipped Virtual Channels
	Type of Input	:	0 to 30 single values, concatenated with & or &&, optional
	Possible Values	:	numeric, 0-30
	Default Value	:

FCBAB	Parameterization of frame code and answering byte
	Type of Input	:	Single value, optional
	Possible Values	:	two-digit, hexadecimal
	Default Value	:	DFH
	The hex value to be entered is based on the following context:
	In the byte to be parameterized, the answer byte is parameterized in bits 1 and 4 through 8 by counting down from the bit with the highest value. Bit 2, which is free, is used to store information on the frame code. This bit position evaluates the loadware in regard to "bit 1" for the frame code.
	The hex value to be entered is thus derived from the bit pattern for the parameterization of the answer byte (AB) and the frame code(FC).
	Byte to be parameterized:
				(bit with lowest value on the right!)

				bits 1 and 4 through 8 of the AB are entered.
				Bit 2 : here bit 1 of the FC is entered.
				Bit 3 is free.

FIXEDTEI	Option to specify a value other than 0 for "FIXED TEI" for point-to-point connections
	Type of Input	:	Single value, optional
	Possible Values	:	0 - 63
	Default Value	:	0

FORMAT	Format of output
	Type of Input:		single value, optional
	Possible Values		L long output format S short output format
	Default Value	:	L

ICPN	Internal call priority number
	Type of Input	:	Single value, 2. parameter of a min-1-group, optional
	Possible Values	:	numeric, 0-16
	Default Value	:	11

INFO	Service Informations
	Type of Input:		single value, optional
	PossibleValues	:	text, up to 50 characters

INFOPAT	Service info text pattern
	Type of Input:		single value, optional
	Possible Values	:	text, up to 50 characters

IPLDS	The default intrude level assumed by CDG for DPNSS party
	Type of Input		single value, 21. parameter of a min-1-group, optional
	Possible Values		A	intrusion allowed
			NA	intrusion not allowed

ITR	HICOM internal trafic restrictions number
	Type of Input		single value, optional
	Possible Values		numeric, 0-15

LCOS	LCR Class of service (Hicom)
	Type of Input		1 to 8 single values, concatenated with &, optional
	Possible Values		numeric, 1-32

LCOSMAP	Enable mapping of LCOS and TRG values?
	Type of Input		single value, optional
	Possible Values		YES
			No

LNTYPE	Line type
	Type of Input	:	max.two linked single values, optional
	The values COPPER AND OWG may be set only alternatively
	Possible Values	:	COPPER	4-wire copper connection
			OWG	Optical wave guide
			AERIAL	aerial connection
	Default Value	:	COPPER

LSCF	loadware saved compressed in flash
	Type of Input	:	single value, optional
	Possible Values	:	Y N	YES NO
	Default Value	:	N	N

LWPARREF	output lwpar reference information
	Type of Input		single value, optional
	Possible Values		Y N

MASTER	Meaning of Layer 2 message (e.g. DIUS2)
	(Command / Response : Master, Slave)
	Type of Input	:	Single value, optional
	Possible Values	:	Y	Master
			N	Slave
	Default Value	:	N

MAXTMS	DPNSS Maximum Transit Message Size
	Type of Input	:	single value, optional
	Possible Values	:	numeric, 0-2048
	Default Value	:	500

MFCB	Parameterization of multiple frame code
	Type of Input	:	Single value, optional
	Possible Values	:	two-digit, hexadecimal
	Default Value	:	FEH
	Note	:	Value H’0B must be specified for use in France.

NSFIV	NSF IE Code to Access VPN Calling service
	Type of Input	:	Single value, optional
	Possible Values	:	0-31
	Default Value	:	1

NSFTSC	NSF IE Code to Activate CA-TSC
	Type of Input	:	Single value, optional
	Possible Values	:	0-31
	Default Value	:	9

NSIMSGS	msg size nsi to non nsi switchover
	Type of Input	:	single value, optional
	Possible Values	:	numeric, 100-2048
	Default Value		150

NSIOUT	Insert nsi dpnss outgoing
	Type of Input	:	single value, optional
	Possible Values	:	Y N	YES NO
	Default Value		Y

NSITR	NSI CORNET-NQ Transit
	Type of Input	:	single value, optional
	Possible Values	:	Y N	YES NO
	Default Value		Y

OCTMAX	Maximum number of octets in an information field. Value is specified in number of octets.
	Type of Input		single value, 9. parameter of a min-1-group
	Possible Values		3-260
	Default Value		260

OESDISTH	Out of frame errored seconds disqualification threshold. Number of OES before disqualification of the reference clock occurs. Value is specified in seconds.
	Type of Input		single value, 3. parameter of a min-1-group
	Possible Values		1 - 65535
	Default Value		30

OESREQTH	Out of frame errored seconds requalification threshold. Maximum number of OES which may occur during the requalification interval before requalification of the reference clock source will occur. Value is specified in seconds
	Type of Input		single value, 4. parameter of a min-1-group
	Possible Values		1 - 65535
	Default Value		4

OPMODE	Board operation mode
	Type of input		0 to 6 single values, concatenated with &,
	Possible Values		BDETON	bipolar violation detection on
			BISUB8ON	bipolar 8 substitution on
			FRAMEESF	extended framing
			NETUSER	user will emulate network end of the digital span
			TABSON	digital link switch enable tabs
			TIMLOOP	loopback state - TMD frame timing driven by loop

PATM	Pause time for DTMF dialing (dual tone multifrequency signaling)
	Type of Input	:	Single value, optional
	Possible Values	:	20 - 255 ms
	Default Value	:	40 ms

PATTERN	Idle bit pattern for the B-channels on the route
	Type of Input	.	Single value, optional
	Possible Values	:	two-digit, hexadecimal
	Default Value	:	D5H

PERMACT	PCM link is permanently active
	Type of Input	:	Single value, 11. parameter of a min-1-group, optional
	Possible Values	:	Y, N
	Default Value	:	Y

PRIMDXTG	Primary Realitis DX trunk group number
	Type of Input		single value, optional
	Possible Values		numeric, 0-254

PROT	Protocol - relevant for CORNET-N protocol only
	Type of Input	:	single value, optional
	Possible Values	:	DASS DPNSS	dass/cornet-n dpnss/cornet-n
	Default Value	:	DPNSSN

PUTM	Pulse time for DTMF dialing (dual tone multifrequency signaling)
	Type of Input	:	Single value, optional
	Possible Values	:	20 - 100 ms
	Default Value	:	60 ms


QUAL	Activate CRC4 procedures on the DIUC (e.g. use in Denmark).
	The two parameters QUAL1 and QUAL2 which are only evaluated if QUAL is set to ON are also included in these procedures.
	Type of Input	:	Single value, optional
	Possible Values	:	ON	Ascertain transmission quality
			OFF	Do not ascertain transmission quality
	Default Value		ON

QUAL1	Time (sec.) for transmission quality worse than 10
	If an error occurs during the specified time, the path is taken out of service!
	This parameter is only in effect if parameter QUAL=ON.
	Type of Input	:	Single value, optional
	Possible Values	:	0 - 255 sec.
	Default Value	:	10 sec.

QUAL2	Time (min.) for transmission quality worse than 10
	If an error occurs during the specified time, the route is taken out of service!
	This parameter is only in effect if parameter QUAL=ON.
	Type of Input	:	Single value, optional
	Possible Values	:	0 - 255 min.
	Default Value	:	10 min.

RES3	Reserve 3 - may be used for test purpose
	Type of Input	:	single value, optional
	Possible Values	:	0 - 65535
	Default Value	:	0

RES4	Reserve 4 - may be used for test purpose
	Type of Input	:	single value, optional
	Possible Values	:	0 - 65535
	Default Value	:	0

RES5	Reserve 5 - may be used for test purpose
	Type of Input	:	single value, optional
	Possible Values	:	0 - 65535
	Default Value	:	0

RESTALL	restart all laps at startup
	Type of Input	:	single value, optional
	Possible Values	:	N Y	NO YES
	Default Value	:	Y

RESTLNK	restart link at startup
	Type of Input	:	single value, optional
	Possible Values	:	N Y	NO YES
	Default Value	:	Y

RETMAX	Maximum number of retransmissions. Maximum number of retransmissions before an error is re-ported.
	Type of Input		single value, 10. parameter of a min-1-group
	Possible Values		1-10
	Default Value		3

RRG	Route restriction group (realitis DX)
	Type of Input		1 to 8 single values, concatenated with &, optional
	Possible Values		numeric, 0-127

SADRTM	DASS-CorNet subaddress translation methode
	Type of Input	:	single value, optional
	Possible Values	:	NSAP USER	network service access point user specified
	Default Value	:	NSAP

SCCONF	Station controlled conference
	Type of Input	:	single value, 6. parameter of a min-1-group
	Possible Values	:	N Y	no yes
	Default Value	:

SESDISTH	severely errored seconds disqualification threshold. Number of sequential SES before disqualification of the reference clock occurs. Value is specified in tenth of seconds
	Type of Input		single value, 5. parameter of a min-1-group
	Possible Values		numeric, 1-65535
	Default Value		10

SESREQTH	Severely errored seconds requalification threshold. Number of sequential seconds with SES absent before requalification of the reference clock occurs. Value is specified in tenth of seconds
	Type of Input		single value, 6. parameter of a min-1-group
	Possible Values		numeric, 1-65535
	Default Value		10

SMD	Layer 1 configuration (subscriber module digital)
	If circuits are allocated with the device type S2COD (AMO TDCSU), SMD must be declared as N (no). If Y (yes) is entered, then all allocated circuits entered in the reference clock table (AMO REFTA) must have a priority of ’0’.
	Type of Input	:	Single value, optional
	Possible Values	:	Y	SMD
			N	TMD
	Default Value	:	N

SOURCE	Location of LWPAR block; indicates where the block has to be copied from
	Type of Input		single value, optional
	Possible Values		HD	Harddisk
			DB	Database


SPD1	Assignment of the 16 speed dialing groups from the system to the
SPD2	6 speed dialing groups for WTK (AC voice frequency signaling)
SPD3	Type of Input	:	Single value, optional
SPD4	Possible Values	:	0	Assignment to central SPD
SPD5			1 - 15	Assignment to certain SPD groups
SPD6	Default Value	:	1

SPDC1	Central 1 automatic dialer
	Type of Input		single value, optional
	Possible Values		numeric, 0-16

SPDCDSS	Parameter indicat. that the spdc from the ss is not transm.
	Type of Input		0 to 2 single values, concatenated with &, 21. parameter of a min-1-group
	Possible Values		NO	no
			SPD	speed dialing
			SPDC	speed dialing, central

STABTIM	Stabilization time for pos. messages and message pairs for a PCM link
	The timer only goes into effect if message delay is switched on in central system data (AMO ZAND, branch ALLDATA, parameter MSGDELAY).
	Type of Input	:	Single value, optional
	Possible Values	:	30-180 sec
	Default Value	:	180 sec

SUPPTIM	Suppression time for further error messages for PCM link
	The timer only goes into effect if message delay is switched on in central system data (AMO ZAND, branch ALLDATA, parameter MSGDELAY).
	Type of Input	:	Single value, optional
	Possible Values	:	10-60 sec
	Default Value	:	60 sec

T301	Timer T301
	Type of Input	:	single value, optional
	Possible Values	:	0-255
	Default Value		180 sec

T302	Timer T302
	Type of Input	:	single value, optional
	Possible Values	:	0-255
	Default Value		10 sec

T303	Timer T303
	Type of Input	:	single value, optional
	Possible Values	:	0-255
	Default Value		4 sec

T304	Timer T304
	Type of Input	:	single value, optional
	Possible Values	:	0-255
	Default Value		15 sec

T305	Timer T305
	Type of Input	:	single value, optional
	Possible Values	:	0-255
	Default Value		30 sec

T308	Timer T308
	Type of Input	:	single value, optional
	Possible Values	:	0-255
	Default Value		4 sec

T309	Timer T309
	Type of Input	:	single value, optional
	Possible Values	:	0-255
	Default Value		90 sec

T310	Timer T310
	Type of Input	:	single value, optional
	Possible Values	:	0 - 255
	Default Value		10 sec

T313	Timer T313
	Type of Input	:	single value, optional
	Possible Values	:	0 - 255
	Default Value		4 sec

T314	Timer T314
	Type of Input	:	single value, optional
	Possible Values	:	0 - 255
	Default Value		4 sec

T316	Timer T316
	Type of Input	:	single value, optional
	Possible Values	:	0 - 255
	Default Value		120 sec

T322	Timer T322
	Type of Input	:	single value, optional
	Possible Values	:	0 - 255
	Default Value		4 sec

TAMOST	Timer AMO Supervision Timeout
	Type of Input	:	single value, optional
	Possible Values	:	0-255
	Default Value		60 sec

TAROB	Timer for automatic redirection on busy
	Type of Input	:	single value, 22. parameter of a min-1-group
	Possible Values	:	numeric, 1-63
	Default Value		10

TBID	timer callback interdigit
	Type of Input	:	single value, optional
	Possible Values	:	:numeric, 1-20
	Default Value	:	5 SEC	:
				:
TBL	Mapping tables between HICOM and Realitis DX
	Type of Input		single value, mandatory
	Possible Values		DXTGITR	Trunk-trunk barring
			LCOSDRRG	Mapping table LCOSD to RRG
			LCOSVRRG	Mapping table LCOSV to RRG
			TRGCBG	Mapping table TRG to CBG

TDPNSSC	Timer DPNSS Collision
	Type of Input	:	single value, optional
	Possible Values	:	numeric, 0-50 in 100msec steps (range 0-5000 msec)
	Default Value	:	5 (500 msec)

TEIVERIF	TEI is verified upon request by the partner.
	Type of Input	:	Single value, optional
	Possible Values	:	Y, N
	Default Value	:	N

TEMPSIG	Temporary Signaling Connection
	Type of Input	:	single value, optional
	Possible Values	:	Y YES N NO
	Default Value	:	Y

TIDOP	DPNSS trunk identity (TID) option
	Type of Input	:	single value, optional
	Possible Values	:	Y YES N NO
	Default Value	:	N

TIPL	Timer to delay the sending of IPL Req after call is conn.
	Type of Input	:	single value, 20. parameter of a min-1-group
	Possible Values	:	numeric, 0-60, 63

TMDTYPE	TMD board type
	Type of Input	:	single value, mandatory
	Possible Values		TMDMOS	Board type MOS
			TMDBOS	Board type BOS

TRG	Traffic restrictions group (Hicom)
	Type of Input		1 to 8 single values, concatenated with &, optional
	Possible Values		numeric, 0-15

TROPTBR	Timer ROPT Release - both end released
	Type of Input	:	single value, optional
	Possible Values	:	numeric, 1-100
	Default Value		10

TROPTNR	Timer ROPT Release - neither end released
	Type of Input	:	single value, optional
	Possible Values	:	numeric, 0-100
	Default Value		0

TSABMR	Timer DPNSS SABMR Retransmission
	Type of Input	:	single value, optional
	Possible Values	:	numeric, 0-255
	Default Value		0 SEC

TTSC	TSC (Temporary Signalling Connection) Timer.
	Type of Input	:	Single value, optional
	Possible Values	:	4-12
	Default Value	:	4

TWEOS	Timer wait for EOS from CORNET
	Type of Input	:	single value, optional
	Possible Values	:	numeric, 1-100
	Default Value		60 SEC

TYPE	Selection of circuit types to be processed (memory addressing)
	Type of Input	:	Single value, mandatory (CHANGE)
			Single value, optional (DISPLAY, REGENERATE)
	Possible Values	:	ANALOG	Circuit analog - NWWTK (DELETE)
			CDG	Cornet dpnss1 gateway
			CDGVAR	Country specific variants for cdg blocks
			DIUC	DIUC modul
			DIUS2	DIU-S2 modul
			DIUS2VAR	Country specific variants for diu-s2 blocks
			NWWTK	Networking wtk set type
			TMD	TMDN64 module

UNWD	user/network definition
	Type of Input	:	single value, optional
	Possible Values	:	DPACN dpnss:a/cornet: network DPACU dpnss:a/cornet: user DPBCN dpnss:b/cornet: network DPBCU dpnss:b/cornet: user
	Default Value		DPACN

VARNO	Number of country specific variant on hard disk
	Type of Input		1 to 2 single values, concatenated with &&, optional (DISPLAY)
			ingle value, mandatory (COPY)
	Possible Values		numeric,1-255

VCHCONF	dpnss virtual chanels x/y configuration
	Type of Input	:	0 to 30 single values, concatenated with & or &&, optional
	Possible Values	:	numeric, 1-30
	Default Value
		:
VERSION	Version of module (e.g. DIUS2)
	Type of Input	:	Single value, optional
	Possible Values	:	S1	US version
			S2	S2 version
	Default Value	:	S2

VMSYSTAD	Version of DIU-S2 module
	Type of Input		single value, 2. parameter of a min-1-group
	Possible Values		numeric, up to 22 characters

WINDOW	Maximum number of outstanding information(I) frames. when this figure is reached, transmission is suspended until a response frame is received. Value is specified in number of frames.
	Type of Input		single value, 11. parameter of a min-1-group
	Possible Values		1-127
	Default Value		7

OpenScape 4000 V10, Volume 1: AMO Descriptions, Service Documentation, Issue 5, ID: P31003H31A0S107057620

© 09/2025 Mitel Networks Corporation. - All rights reserved.
Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG. All other trademarks herein are the property of their respective owners.