198.2.2
CHANGE-TSCSU
All parameters are optional except for PEN and DEV.
If the trunk to be changed is assigned to a trunk group, all the trunks of that trunk group are changed, unless the operator declares a value for the parameter CCT.
When canceling trunks from a trunk group (by specifying TGRP=0), the operator must ensure that those trunk groups allocated to a route access code always contain at least one device entry.
If the operating mode of a CCM is changed to ’meet-me’, an access code with the DAR CCMANS (see AMO
WABE
) must be assigned using the AMO
RICHT
. Similarly, if the ’meet-me’ operating mode for a CCM is cancelled, the routing access code with DAR CCMANS must also be deleted (with the AMO
RICHT
).
A trunk to be changed does not have to be deactivated.
However, changes of the data described by the parameters COFIDX, WIRES and DTYPE take effect only after these has been loaded at the trunk. The loading can be done by AMO-TSCSU (OFFTYPE=DC or DI) or explicitly by the user.
1.
OFFTYPE=NL:
Advisorvy H04 reminds the user to force loading.
2.
OFFTYPE=DC:
The trunk is soft locked. If the lock was successful, the trunk data is changed and the trunk is activated again forcing trunk data loading. If the trunk is busy, trunk data is changed but the user has to force loading explicitly (H04).
3.
OFFTYPE=DI:
The trunk is locked, the trunk data is changed and the trunk is activated again forcing trunk data loading.
Procedure Overview
Command Code
Parameter
CHANGE-TSCSU
PEN=<gg-u-sss-cc>,[COTNO=<number>],[DPLN=<number>]
,[ITR=<number>],[TGRP=<number>]
,[CCT=<string>],[ALARMNO=<param>]
,[SRCGRP=<number>]
,[OFFTYPE=<param>]
,DEV=DICT,[COFIDX=<dd>],[COPNO=<number>]
,[SUPV=<param>],[ACKT=<param>],[DTYPE=<dd>];
|,DEV=CC,[COFIDX=<dd>],[COPNO=<number>]
,[WIRES=<dd>],[SUPV=<param>]
,[ACKT=<param>],[STADIAL=<param>],[ABLK=<param>]
,[STNOLEN=<number>];
|,DEV=CCM,[COFIDX=<dd>],[COPNO=<number>]
,[WIRES=<dd>],[SUPV=<param>]
,[ACKT=<param>],[STADIAL=<param>]
,[STNOLEN=<number>],[TBT=<param>],[EOD=<param>]
,[SRCHORD=,NUMBER>},[SRCHATT=<number>]
,[OPTYPE=<param>],[WAIT=<param>],[SRCHANT=<param>]
,[WAITT=<param>],[CDGT=<dd>]
,[CONV=<param>],[MABLK=<number>];
|,DEV=DOOR|SPKR|ANS|RA,[COFIDX=<dd>],[COPNO=<number>]
,[SUPV=<param>],[ACKT=<param>];
|,DEV=RAS,[COFIDX=<dd>],[COPNO=<number>]
,[SUPV=<param>],[ACKT=<param>],[ANNTYPE=<number>];
Example
Change the parameter ’COPNO’ for the trunk at port 1-2-013-1.
Input:
CHANGE-TSCSU:PEN=1-2-013-1,COPNO=4;
Output:
H03: TRUNK AT PEN 01-02-013-01 CHANGED
OpenScape 4000 V10, Volume 1: AMO Descriptions, Service Documentation, Issue 5
, ID:
P31003H31A0S107057620
©
09/2025
Mitel Networks Corporation. - All rights reserved.
Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG. All other trademarks herein are the property of their respective owners.