202.4.1 Error messages

 
F01:
<aaa> <xxxx> NOT ADDED (NEQ)
F02:
<aaa> <xxxx> NOT ADDED (<reason>)
F03:
LTU <xxxx>: LTU BOARDS ARE NOT (ALL) DELETED
F04:
LTG <xx>: LTU-S OF LTG ARE NOT (ALL) DELETED
F05:
ENTERED LTU <xx> IS ALREADY USED AS OVERLAY LTU FOR LTU <xx>.
F06:
PART NUMBER NOT FOUND IN BOARD TABLE
F07:
<aaa> <xxxx> NOT DELETED (ORDER ERROR)
F08:
CANNOT LOAD SUBSYSTEM "UBGDAT0"
F10:
FOR THIS PLATFORM ONLY LTG 1 TO <xx> ALLOWED
F11:
CONFIGURATION RUN STARTED - FURTHER START NOT ALLOWED
F12:
FOR THIS PLATFORM ONLY LTU 1 - <xx> ALLOWED,
FOR UNIT=AP ONLY THE RANGE 17 TO 99 IS ALLOWED
F14:
<aaa> <xxxx> IS ALREADY ADDED
F15:
ADDRESS <ip1.ip2.ip3.ip4> FOR PARAMETER <param> IS NOT VALID,
 
BECAUSE THIS VALUE IS EQUAL TO THE CC-A/CC-B ADDRESS OF LS NET.
F16:
LTG <xx> CANNOT BE ASSIGNED; MEMORY VALUE FOR PARAMETER PERMDL
MUST BE AT LEAST 20 (AMO DIMSU)
F17:
THE PERMITTED NUMBER OF MODULE TYPES HAS ALREADY BEEN ASSIGEND
F18:
THE NEW FRAMETYPE CANNOT BE CONFIGURED BECAUSE BOARDS ARE STILL CONFIGURED
AT SLOTS WHICH ARE NOT COVERED BY THE NEW FRAMETYPE.
F20:
SINCE PAYLOAD ENCRPTION AND/OR DMC IS ENABLED, MANUAL CHANGE OF B-CHANNEL
AMOUNTS IS NOT ALLOWED.
F21:
THE PERMITTED NUMBER OF SIU MODULES IST ALREADY IMPLEMENTED
F22:
MODULE PART NUMBER INVALID
F23:
THE ENTERED SIU MODULE IST NOT ALLOWED IN THE PARTICULAR SYSTEM
F24:
LTG <xx> THERE ARE STILL FICTIVE LINES EXISTING
F26:
THE LTUC PARTNO DOES NOT MATCH THE HW TYPE
F27:
THE SPECIFIED PART NUMBER IS NOT CORRECT
F40:
THE ENTERED FRMTYPE IS GENERALLY NOT ALLOWED FOR THIS SWITCH TYPE.
F41:
THE ENTERED FRMTYPE IS NOT ALLOWED FOR LTU <xx>.
F43:
THE LOCATION ID AND THE LOCATION ADDRESS OF THE LTU MUST BE SPECIFIED,
IF FLEX WAS ENTERED AS TYPE OF THE LTU
F45:
INSUFFICIENT MEMORY FOR AP SHELVES. PLEASE INCREASE MEMORY WITH
AMO DIMSU (PARAMETER: AP).
F46:
THE TDS PORT UPDATE TO THE DATABASE WAS UNSUCCESSFUL
PLEASE CHECK DIMSU VALUES LODEN AND DTILTG
F47:
INSUFFICIENT MEMORY (AMO DIMSU: PARAMETER STN)
F48:
THE IP ADDRESS FOR PARAMETER <xxx> IS NOT WITHIN THE VALID
RANGE OF LS NET<xxx>.
F49:
THE AMO COULD NOT FIND ENOUGH FREE IP-ADDRESSES.
F50:
FOR CONNTYPE=<conntype> PARAMETER <param> MUST BE SPECIFIED
F51:
NO LS NET CONFIGURED
PLEASE CONFIGURE LS NET BY MEANS OF ADD-SIPCO
F52:
IF PARAMETERS PARTNO, BCHLCNT AND/OR PLCHECK ARE CHANGED, IT IS
NECESSARY TO DEACTIVATE THE AP SHELF BY MEANS OF DEACT-USSU AND AFTER
CHANGE TO ACTIVATE IT BY MEANS OF ACT-USSU.
MAYBE SOME DATA WILL BE LOADED TO THE NEW NCUI BOARD AFTER ACTIVATION
WHICH LEAD TO A LOSS OF THE CONNECTION BETWEEN AP AND CENTRAL SHELF!
THEREFORE CHECK ALSO THE CONFIGURATION OF AMO-STMIB AND AMO-APRT.
F53:
THE AP SHELP IS NOT COMPLETELY DECONFIGURED FOR ACTION DELETE.
THE CONNECTION BETWEEN AP SHELF AND CENTRAL SHELF HAS TO BE DEACTIVATED
(EXEC-USSU:DELAP).
FURTHER ALL SHELF SPECIFIC CONFIGURATIONS HAVE TO BE DELETED BY MEANS
OF AMO-BCSU AND AMO-APRT.
F54:
THE DESIRED CONFIGURATION IS GENERALLY NOT ALLOWED FOR THIS HICOM CLASS.
F55:
THE BASIC LTU DATA COULDN'T BE CREATED BY DB.
F56:
THE GIVEN ALARM NUMBER IS NOT VALID BECAUSE IT DOES NOT LEAD EITHER TO A
LOGICAL ALARM OR THE ALARM TYPE DOES NOT MATCH HW-UNIT.
F57:
THE SPECIFIED TIME CLASS IS NOT CONFIGURED. SEE AMO-SIPCO.
F58:
THE CURRENT NCUI IS NOT ALLOWED TO BE CHANGED TO THE SPECIFIED NCUI.
F59:
THE SOFTGATE TYPE CANNOT BE CHANGED AS LONG AS THE CONFIGURED VIRTUAL
GATEWAYS NEED MORE PORTS THAN THE NEW SOFTGATETYPE ALLOWS OR ACTUALLY
REDUNDANCY BOARDS ARE ASSIGNED.
F60:
THE SPECIFIED COMBINATION OF SOFTGATE AND TRADITIONAL HW COMPONENTS
(LTPARTNO AND FRMTYPE) IS NOT ALLOWED.
F61:
SIU TONE TABLES ARE NOT LOADED PROPERLY, PLEASE CONFIGURE ALL
RELEVANT SIU PARAMETERS BY MEANS OF AMO-ZAND FIRST.
F62:
THE GIVEN BOARD TYPE IS NOT ALLOWED ON RG8300.
F63:
IPV6 AND DHCP FUNCTIONALITY IS SUPPORTED ONLY FOR SOFTGATES.
F64:
SURVIVABILITY VIA ALTERNATIVE LAN IS CONFIGURED FOR THE AP.
SIGMODE CANNOT BE CHANGED TO HSRTCP.
F65:
Textaps <filename> not present on Hard Disk.
TEXTSEL <textsel> has not been written to DB.
F66:
ERROR
F67:
LTU SHELVES (1-15) ARE NOT ALLOWED TO BE ADDED WHEN AMO CPCI RTM=NO
F68:
LTU 1.<xx> NOT ADDED AS AP
F69:
LTU 1.<xx> NOT ADDED AS ENTGW
OpenScape 4000 V10, Volume 1: AMO Descriptions, Service Documentation, Issue 5, ID: P31003H31A0S107057620
 © 09/2025 Mitel Networks Corporation. -  All rights reserved.
 Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG. All other trademarks herein are the property of their respective owners.