STMIB - Configuration of Global- and Feature-Board Data for HG3575-2 Boards

AMO STMIB configures the board configuration data of NCUI2 boards. The Board Data consist of

Board specific Global Data
Expanded Global Data consisting of

global Board Data
Ethernet interface Data
service interface Data (NCUI2 only)
QoS parameters for signalling(NCUI2 only)
DSP HW-configuration Data (Set by UCSU)
Sector number of an IPDA-gateway (NCUI2 only)
DMC specific data(NCUI2 only)

Feature Data Box consisting of

IP Routing tables (set by AMO APRT)(NCUI2 only)
ASC configuration data(NCUI2 only)
DSP configuration data(NCUI2 only)
Adaptive Jitter Buffer Data (NCUI2 only)
H.323 Configuration Data(NCUI2 only)
SNMP Config Data(NCUI2)
DLS Config Data(NCUI2)

The configuration data has to be loaded first, then NCUI2 and boards use these data.
Board data may be loaded by means of:

plug into LTU-Shelf
switch on by means of AMO BSSU/ AMO USSU

Advisory messages to according to AMO actions will be issued.
Dynamic loading of board data during operation will be done for feature ASC, DSP, JB, H323 and SNMP after changing successfully. PIT response is timer controlled. For unsuccessful loading of board data an error message will be issued and the AMO STMIB will be aborted. Loading may be unsuccessful for the following reasons:

no board data have been configured
board not present
no response of PIT received within 2 minutes
dynamic board id not present
board not in state 'ready'

Cross Reference to Other AMOs:

AMO DIMSU	Dimensioning of features, switching unit
AMO UCSU	Configuration of NCUI2-board
AMO APRT	Configuration of Routing tables of NCUI2-board

Destination Processor: BP (Switching Unit)

Functions

CHANGE	Change NCUI2 board data	password class 2
DISPLAY	Display NCUI2 board data	password class 1
REGENERATE	Regenerate NCUI2 board data	password class 2

Procedure Overview

CHANGE-STMIB

CHANGE-STMIB

MTYPE=NCUI2,LTU=<number>,

TYPE=SERVIF, {(min 1) LOGINTRM=<string>, LOGINPPP=<string>, PASSW=<string>};

TYPE=GLOBAL,PATTERN=<number>;

TYPE=IFDATA, {(min 1) VLAN=<param>, TOSLAN=<string>, TOSMODEM=<string>, VLANID=<number>, BITRATE=<string>};

TYPE=ASC, {(min 1) UDPPRTLO=<number>, UDPPRTHI=<number>, TOSPL=<string>, T38FAX=<param>, RFCFMOIP=<param>, RFCDTMF=<param>, REDRFCTN=<param>,

[PRIO=PRIO1],[CODEC=<param>], [VAD=<param>], [RTP=<string>];

[PRIO=PRIO2],[CODEC=<param>], [VAD=<param>], [RTP=<string>];

[PRIO=PRIO3],[CODEC=<param>], [VAD=<param>], [RTP=<string>];

[PRIO=PRIO4],[CODEC=<param>], [VAD=<param>], [RTP=<string>];

[PRIO=PRIO5],[CODEC=<param>], [VAD=<param>], [RTP=<string>];

[PRIO=PRIO6],[CODEC=<param>], [VAD=<param>], [RTP=<string>];

[PRIO=PRIO7],[CODEC=<param>], [VAD=<param>], [RTP=<string>];

[PRIO=PRIO8],[CODEC=<param>], [VAD=<param>], [RTP=<string>];

[PRIO=PRIO9],[CODEC=<param>], [VAD=<param>], [RTP=<string>];

TYPE=DSP,[JITBUFD=<string>];

TYPE=DMCDATA, {(min 1) DMCALLWD=<param>, DMCCONN=<number>};

TYPE=H323, {(min 1) Q931T1=<number>, Q931T2=<number>, GWNAME=<string>};

TYPE=JB, {(min 1) AVGDLYV=<number>, MAXDLYV=<number>, MINDLYV=<number>, PACKLOSS=<number>, AVGDLYD=<number>, MAXDLYD=<number>, JBMODE=<number>};

TYPE=SIGQOS, {(min 1) BANDW=<number>, MAXRTD=<number>, MINTHRPT=<number>, SIGPTHSW=<param>, QOSSTAT=<param>};

TYPE=MGNTDATA, {(min 1) MGNTIP=<number>, MGNTPN=<number>, BUSIP=<number>, BUSPN=<number>, UIMODE=<param>};

TYPE=WBMDATA,LOGINWBM=<string>, {(min 1) PASSWWBM=<number>, ROLE=<param>};

TYPE=GWSECTOR,GWSECTNO=<number>;

TYPE=DLSDATA, {(min 1) DLSIPADR=<number>, DLSPORT=<number>, DLSACPAS=<param>};

TYPE=SOCODATA, {(min 1) CLAIPADR=<number>, CLAPORT=<number>};

TYPE=IPCONF, {(min 1) IPMODE=<param>, DHCPV4=<param>, DHCPV6=<param>};

TYPE=MANLANIF, {(min 1) MIPADR=<number>, MNETMASK=<number>, MVLAN=<param>, MVLANID=<number>, MDEFRT=<number>};

TYPE=WANIF, {(min 1) WIPADR=<number>, WNETMASK=<number>, WVLAN=<param>, WVLANID=<number>, WDEFRT=<number>, WPUBIP=<number>};

TYPE=WANFD, {(min 1) WUDPPRTL=<number>, WUDPPRTH=<number>, WTOSPL=<string>, WTOSSIGN=<string>, WTLSP=<number>};

TYPE=LIDHFA,[LIPADR=<number>], [LUDPPRTL=<number>], [LUDPPRTH=<number>], [LTCPP=<number>], [LTLSP=<number>];

MTYPE=INITNCU2,LTU=<number>,

TYPE=GLOBAL;

TYPE=IFDATA;

TYPE=SERVIF;

TYPE=ASC;

TYPE=DSP;

TYPE=DMCDATA;

TYPE=H323;

TYPE=JB;

TYPE=SIGQOS;

TYPE=MGNTDATA;

TYPE=WBMDATA,[LOGINWBM=<string>];

TYPE=DLSDATA;

TYPE=SOCODATA;

TYPE=IPCONF;

TYPE=MANLANIF;

TYPE=WANIF;

TYPE=WANFD;

TYPE=LIDHFA;

TYPE=ALL;

By means of action CHANGE the existing board data may be changed. The changes will not be active at once, because they must be transferred to Loadware of appropriate board. The user will be informed by advisory message, which AMO command is to use. Dynamic loading of board data during operation will be done for feature ASC, DSP, JB, H323, MGNTDATA, WBMDATA,SNMP and DLSACPAS after successful changing. PIT response is timer controlled. For unsuccessful loading of board data an error message will be issued and the AMO STMIB will be aborted. Loading may be unsuccessful for the following reasons:

no board data have been configured
board not present
no response of PIT received within 2 minutes
dynamic board id not present
board not in state 'ready'

The branches MTYPE=INITNCU2 can be used to initialize the board data (delete function). The data types entered by parameter TYPE can be set to default values separately or all together (TYPE=ALL).
The Idle Pattern must be configured according to system Law configuration (CHA-ZAND:TYPE=CONFC,CODE=alaw/ulaw) to prevent payload problems. In case of A-Law the idle code 213 has to be configured, in case of U-Law the proper value is 255.

DISPLAY-STMIB

DISPLAY-STMIB
		[MTYPE=NCUI2], {(max 1) LTU=<number>, SRCGRP=<number>}, [TYPE=<param>];

By means of function DISPLAY the configured board data is issued. Data may be issued sorted by PEN or for NCUI2 boards by Source-Group-Index.

REGENERATE-STMIB

REGENERATE-STMIB
		[MTYPE=NCUI2],[LTU=<number>], [TYPE=<param>];

By means of action REGENERATE, one or more CHANGE commands are regenerated for each board assigned by AMO STMIB.

Parameter description

AVGDLYD	Average Delay Data
	Type of Input:	single value, 5. parameter of a min-1-group
	Possible Values:	numeric, 0-200
	Default Value:	60

AVGDLYV	Average Delay Voice
	Type of Input:	single value, 1. parameter of a min-1-group
	Possible Values:	numeric, 0-218
	Default Value:	8

BANDW	Maximum bandwidth which is usable for the signalling connection to NCUI2 board. Zero means that bandwidth limitation is deactivated.
	Type of Input:	single value, 1. parameter of a min-1-group
	Possible Values:	numeric, 0, 64-250
	Default Value:	0

BITRATE	Bit Rate (Speed&Mode) for NCUI2
	Type of Input:	single value, 5. parameter of a min-1-group
	Possible Values:	100MBFD	100 Mbit/s Full Duplex	36
		100MBHD	100 Mbit/s Half Duplex	35
		10MBFD	10 Mbit/s Full Duplex(only NCUI2+)	34
		10MBHD	10 Mbit/s Half Duplex(only NCUI2+)	33
		AUTONEG	Auto Negotiation	0
	Default Value:	AUTONEG

BUSIP	IP Adress of the Back-Up Server
	Type of Input:	4 single values, concatenated with ., 3. parameter of a min-1-group
	Possible Values:	numeric, 0-255
	Default Value:	0.0.0.0

BUSPN	Port Number of the Back-Up Server
	Type of Input:	single value, 4. parameter of a min-1-group
	Possible Values:	numeric, 1-65535
	Default Value:	443

CLAIPADR	CLA IP address for softGate vHG3575
	Type of Input:	4 single values, concatenated with ., 1. parameter of a min-1-group
	Possible Values:	numeric, 0-255

CLAPORT	Port Number for softGate vHG3575
	Type of Input:	single value, 2. parameter of a min-1-group
	Possible Values:	numeric, 0-65535

CODEC	Codec
	Type of Input:	single value, optional
	Possible Values:	G711A	G711 A-Law, uncompresed	DB_VC_G711
		G711U	G711 U-Law, uncompresed	DB_VC_G711U
		G722	G722, compressed	DB_VC_G722
		G729	G729, compressed	DB_VC_G729
		G729A	G729, compressed	DB_VC_G729A
		G729AB	G729, compressed	DB_VC_G729AB
		G729B	G729, compressed	DB_VC_G729B
		NONE	No Codec	DB_VC_NULL
		OPUS	OPUS, compressed	DB_VC_OPUS
	Default Value:	G711A&G729

DHCPV4	DHCP for IP V4
	Type of Input:	single value, 2. parameter of a min-1-group
	Possible Values:	N	No	0
		NO	No	0
		Y	Yes	1
		YES	Yes	1
	Default Value:	NO

DHCPV6	DHCP for IP V6
	Type of Input:	single value, 3. parameter of a min-1-group
	Possible Values:	N	No	0
		NO	No	0
		Y	Yes	1
		YES	Yes	1
	Default Value:	NO

DLSACPAS	PIN required for DLS Bootstrapping
	Type of Input:	single value, 3. parameter of a min-1-group
	Possible Values:	N	No	0
		NO	No	0
		Y	Yes	1
		YES	Yes	1
	Default Value:	value from AMO-ZANDE

DLSIPADR	DLS server IP address
	Type of Input:	4 single values, concatenated with ., 1. parameter of a min-1-group
	Possible Values:	numeric, 0-255
	Default Value:	value from AMO-ZANDE

DLSPORT	Port Number of DLS server
	Type of Input:	single value, 2. parameter of a min-1-group
	Possible Values:	numeric, 0-65535
	Default Value:	value from AMO-ZANDE

DMCALLWD	DMC enabled
	Type of Input:	single value, 1. parameter of a min-1-group
	Possible Values:	N	No	0
		NO	No	0
		Y	Yes	1
		YES	Yes	1
	Default Value:	NO

DMCCONN	Number of DMC connections
	Type of Input:	single value, 2. parameter of a min-1-group
	Possible Values:	numeric, 0-255
	Default Value:	0

GWNAME	Gateway Name
	Type of Input:	single value, 3. parameter of a min-1-group
	Possible Values:	text (case sensitive), up to 16 characters
	Default Value:	HG3575-2

GWSECTNO	Sector number of an IPDA
	Type of Input:	single value, mandatory
	Possible Values:	numeric, 0-2400

IPMODE	IP Mode
	Type of Input:	single value, 1. parameter of a min-1-group
	Possible Values:	DUALSTCK	IP Version 4 and Version 6	DB_IPM_IP_V4_V6
	Possible Values:	IPV4	IP Version 4	DB_IPM_IP_V4

JBMODE	Jitter Buffer Mode
	Type of Input:	single value, 7. parameter of a min-1-group
	Possible Values:	numeric, 1-2
	Default Value:	CHANGE for MTYPE=INITNCU2: 2

JITBUFD	Jitter buffer depth (msec)
	Type of Input:	single value, optional
	Possible Values:	0	0 ms	0
		10	10 ms	1
		100	100 ms	10
		110	110 ms	11
		120	120 ms	12
		130	130 ms	13
		140	140 ms	14
		150	150 ms	15
		160	160 ms	16
		170	170 ms	17
		180	180 ms	18
		190	190 ms	19
		20	20 ms	2
		200	200 ms	20
		210	210 ms	21
		30	30 ms	3
		40	40 ms	4
		50	50 ms	5
		60	60 ms	6
		70	70 ms	7
		80	80 ms	8
		90	90 ms	9
	Default Value:	60

LIPADR	IP Adress of the HFA LAN
	Type of Input:	4 single values, concatenated with ., optional
	Possible Values:	numeric, 0-255
	Default Value:	0.0.0.0

LOGINPPP	User Login for PPP connection
	Type of Input:	single value, 2. parameter of a min-1-group
	Possible Values:	text, up to 10 characters
	Default Value:	HIPATH

LOGINTRM	User Login for terminal mode
	Type of Input:	single value, 1. parameter of a min-1-group
	Possible Values:	text, up to 10 characters
	Default Value:	HICOM

LOGINWBM	User Login for WBM Connection
	Type of Input:	single value, mandatory	(CHANGE,MTYPE=NCUI2-NCUI2 board,TYPE=WBMDATA-WBM Login Data)
		single value, optional	(CHANGE,MTYPE=INITNCU2-Initialize NCUI2 board,TYPE=WBMDATA-WBM Login Data)
	Possible Values:	text, up to 11 characters

LTCPP	TCP Port Number LAN
	Type of Input:	single value, optional
	Possible Values:	numeric, 1-65535
	Default Value:	4060

LTLSP	TLS Port Number LAN
	Type of Input:	single value, optional
	Possible Values:	numeric, 1-65535
	Default Value:	4061

LTU	Line trunk unit
	Type of Input:	0 to 2 single values, concatenated with &&, 1. parameter of a max-1-group	(DISPLAY,MTYPE=NCUI2-NCUI2 board)
		0 to 2 single values, concatenated with &&, optional	(REGENERATE,MTYPE=NCUI2-NCUI2 board)
		single value, mandatory	(CHANGE,MTYPE=INITNCU2-Initialize NCUI2 board / CHANGE,MTYPE=NCUI2-NCUI2 board)
	Possible Values:	numeric, 0, 17-99	(CHANGE,MTYPE=NCUI2-NCUI2 board)
		numeric, 1-15, 17-99	(CHANGE,MTYPE=INITNCU2-Initialize NCUI2 board)
		numeric, 17-99	(DISPLAY,MTYPE=NCUI2-NCUI2 board / REGENERATE,MTYPE=NCUI2-NCUI2 board)

LUDPPRTH	UDP Port Number - High Limit
	Type of Input:	single value, optional
	Possible Values:	numeric, 29100-30099
	Default Value:	30099

LUDPPRTL	UDP Port Number - Low Limit
	Type of Input:	single value, optional
	Possible Values:	numeric, 29100-30099
	Default Value:	29100

MAXDLYD	Maximum Delay Data
	Type of Input:	single value, 6. parameter of a min-1-group
	Possible Values:	numeric, 40-250
	Default Value:	200

MAXDLYV	Maximum Delay Voice
	Type of Input:	single value, 2. parameter of a min-1-group
	Possible Values:	numeric, 8-368
	Default Value:	88

MAXRTD	Maximum acceptable Round Trip Delay for the signalling connection to NCUI2 board. Zero means that the measurement of the round trip delay is deactivated.
	Type of Input:	single value, 2. parameter of a min-1-group
	Possible Values:	numeric, 0, 400-600
	Default Value:	0

MDEFRT	IP address of the default router within the LAN segment The default router takes care of routing forward all packets with a destination address with a network part different from the own LAN segment. 0.0.0.0 means that no default router is configured.
	Type of Input:	4 single values, concatenated with ., 5. parameter of a min-1-group
	Possible Values:	numeric, 0-255
	Default Value:	0.0.0.0 (no Default Router)

MGNTIP	IP Adress of the Management Station
	Type of Input:	4 single values, concatenated with ., 1. parameter of a min-1-group
	Possible Values:	numeric, 0-255
	Default Value:	0.0.0.0

MGNTPN	Port Number of the Management Station
	Type of Input:	single value, 2. parameter of a min-1-group
	Possible Values:	numeric, 1024-65535
	Default Value:	8000

MINDLYV	Minimum Delay Voice
	Type of Input:	single value, 3. parameter of a min-1-group
	Possible Values:	numeric, 0-48
	Default Value:	0

MINTHRPT	Minimum required throughput for the signalling connection to NCUI2 board. Zero means that the measurement of the throughput is deactivated.
	Type of Input:	single value, 3. parameter of a min-1-group
	Possible Values:	numeric, 0, 32-90
	Default Value:	0

MIPADR	Source IP address of CGW board
	Type of Input:	4 single values, concatenated with ., 1. parameter of a min-1-group
	Possible Values:	numeric, 0-255
	Default Value:	0.0.0.0

MNETMASK	IP net mask of LAN segment The IP net mask determines the network and the host partition of an IP address. All IP addresses of a LAN segment must contain the identical network addresss part but different host address parts (also the Default Router must fulfill this requirement).
	Type of Input:	4 single values, concatenated with ., 2. parameter of a min-1-group
	Possible Values:	numeric, 0-255
	Default Value:	0.0.0.0

MTYPE	Board type
	Type of Input:	single value, mandatory		(CHANGE)
	Type of Input:	single value, optional		(DISPLAY / REGENERATE)
	Possible Values:	INITNCU2	Initialize NCUI2 board	(CHANGE)
	Possible Values:	NCUI2	NCUI2 board

MVLAN	VLAN tagging on LAN-IF
	Type of Input:	single value, 3. parameter of a min-1-group
	Possible Values:	N	No	0
		NO	No	0
		Y	Yes	1
		YES	Yes	1
	Default Value:	NO

MVLANID	Virtual LAN Identification Special settings are required by certain LAN equipment (routers...), in other cases the VLAN Id should be set to 0 (default)
	Type of Input:	single value, 4. parameter of a min-1-group
	Possible Values:	numeric, 0-4095
	Default Value:	0

PACKLOSS	Packet Loss Preference
	Type of Input:	single value, 4. parameter of a min-1-group
	Possible Values:	numeric, 0-8
	Default Value:	4

PASSW	Password-1
	Type of Input:	single value, 3. parameter of a min-1-group
	Possible Values:	text (case sensitive), up to 19 characters

PASSWWBM	Encrypted Password for WBM Connection
	Type of Input:	16 single values, concatenated with -, 1. parameter of a min-1-group
	Possible Values:	numeric, 0-255

PATTERN	Coding of idle pattern
	Type of Input:	single value, mandatory
	Possible Values:	numeric, 213-255

PRIO	Priority list for Codec settings
	Type of Input:	single value, 8. parameter of a min-1-group
	Possible Values:	PRIO1	Priority 1
		PRIO2	Priority 2
		PRIO3	Priority 3
		PRIO4	Priority 4
		PRIO5	Priority 5
		PRIO6	Priority 6
		PRIO7	Priority 7
		PRIO8	Priority 8
		PRIO9	Priority 9

Q931T1	Q931 Timer 1: Response Timout in seconds
	Type of Input:	single value, 1. parameter of a min-1-group
	Possible Values:	numeric, 4-120
	Default Value:	50 (H'32)

Q931T2	Q931 Timer 2: Connect Timout in seconds
	Type of Input:	single value, 2. parameter of a min-1-group
	Possible Values:	numeric, 180-600
	Default Value:	500 (H'1F4)

QOSSTAT	If this switch is set, the QoS statistics data of signalling connection to this NCUI2 board will be displayed on user terminal - precondition is that the output is generally enabled via AMO-DIAGS (CC/HSR switch S00).
	Type of Input:	single value, 5. parameter of a min-1-group
	Possible Values:	NO	No	FALSE
	Possible Values:	YES	Yes	TRUE
	Default Value:	NO

REDRFCTN	Redundant transfer of RFC2833 tones according to RFC2198 IMPORTANT: The parameters REDRFCTN/RFCDTMF/RFCDFMOIP must have the same value in all IPDA gateways (STMI2/4 with regard to AMO CGWB & NCUI2+/4 with regard to AMO STMIB). This avoids problems and a common function across all systems is achieved!
	Type of Input:	single value, 7. parameter of a min-1-group
	Possible Values:	N	No	0
		NO	No	0
		Y	Yes	1
		YES	Yes	1
	Default Value:	CHANGE for MTYPE=INITCGW: YES

RFCDTMF	Transfer DTMF tones according to RFC2833 IMPORTANT: The parameters REDRFCTN/RFCDTMF/RFCDFMOIP must have the same value in all IPDA gateways (STMI2/4 with regard to AMO CGWB & NCUI2+/4 with regard to AMO STMIB). This avoids problems and a common function across all systems is achieved!
	Type of Input:	single value, 6. parameter of a min-1-group
	Possible Values:	N	No	0
		NO	No	0
		Y	Yes	1
		YES	Yes	1
	Default Value:	CHANGE for MTYPE=INITCGW: YES

RFCFMOIP	Transfer fax/modem tones according to RFC2833 IMPORTANT: The parameters REDRFCTN/RFCDTMF/RFCDFMOIP must have the same value in all IPDA gateways (STMI2/4 with regard to AMO CGWB & NCUI2+/4 with regard to AMO STMIB). This avoids problems and a common function across all systems is achieved!
	Type of Input:	single value, 5. parameter of a min-1-group
	Possible Values:	N	No	0
		NO	No	0
		Y	Yes	1
		YES	Yes	1
	Default Value:	CHANGE for MTYPE=INITCGW: NO

ROLE	Role of the WBM-User
	Type of Input:	single value, 2. parameter of a min-1-group
	Possible Values:	ADMIN	Administrator (Standard WBM administration)	DB_WBM_ROLE_ADMIN
		ENGR	Developer(Access all -incl. hidden features)	DB_WBM_ROLE_ENGR
		READONLY	Administrator with read-only access	DB_WBM_ROLE_READONLY
		SU	Superuser (Access to all features)	DB_WBM_ROLE_SU
	Default Value:	ADMIN

RTP	Size of RTP package (msec)
	Type of Input:	single value, optional
	Possible Values:	10	10 ms	1
		20	20 ms	2
		30	30 ms	3
		40	40 ms	4
		50	50 ms	5
		60	60 ms	6
		70	70 ms	7
		80	80 ms	8
		90	90 ms	9
	Default Value:	20 (G711A) / 30 (G729)

SIGPTHSW	If the QoS limits (MAXRTD, MINTHRPT) are exceeded, the switch over of signalling connection to the survivability path can be requested. In case of EXTEND a switch over will be done either when "bandwidth exceeded" is signalled. Via SURVONLY the signalling connection can be immediately and permanently switched to the survivability path.
	Type of Input:	single value, 4. parameter of a min-1-group
	Possible Values:	EXTEND	Extended (connection lost or network problems)	DB_APE_QOS_SIGSW_EXTENDED
		STD	Standard (switch if connection is lost)	DB_APE_QOS_SIGSW_STANDARD
		SURVONLY	Survivability only (forced via survivability	DB_APE_QOS_SIGSW_SURV_ONLY
	Default Value:	STD

SRCGRP	Source Group Index
	Type of Input:	0 to 2 single values, concatenated with &&, 2. parameter of a max-1-group
	Possible Values:	numeric, 1-255

T38FAX	T.38 fax
	Type of Input:	single value, 4. parameter of a min-1-group
	Possible Values:	N	No	0
		NO	No	0
		Y	Yes	1
		YES	Yes	1
	Default Value:	CHANGE for MTYPE=INITNCU2: YES

TOSLAN	TOS for route via LAN
	Type of Input:	single value, 2. parameter of a min-1-group
	Possible Values:	0	DF	0
		100	DSCP25	100
		104	AF31	104
		108	DSCP27	108
		112	AF32	112
		116	DSCP29	116
		12	DSCP3	12
		120	AF33	120
		124	DSCP31	124
		128	CS4	128
		132	DSCP33	132
		136	AF41	136
		140	DSCP35	140
		144	AF42	144
		148	DSCP37	148
		152	AF43	152
		156	DSCP39	156
		16	DSCP4	16
		160	CS5	160
		164	DSCP41	164
		168	DSCP42	168
		172	DSCP43	172
		176	DSCP44	176
		180	DSCP45	180
		184	EF	184
		188	DSCP47	188
		192	CS6	192
		196	DSCP49	196
		20	DSCP5	20
		200	DSCP50	200
		204	DSCP51	204
		208	DSCP52	208
		212	DSCP53	212
		216	DSCP54	216
		220	DSCP55	220
		224	CS7	224
		228	DSCP57	228
		232	DSCP58	232
		236	DSCP59	236
		24	DSCP6	24
		240	DSCP60	240
		244	DSCP61	244
		248	DSCP62	248
		252	DSCP63	252
		28	DSCP7	28
		32	CS1	32
		36	DSCP9	36
		4	DSCP1	4
		40	AF11	40
		44	DSCP11	44
		48	AF12	48
		52	DSCP13	52
		56	AF13	56
		60	DSCP15	60
		64	CS2	64
		68	DSCP17	68
		72	AF21	72
		76	DSCP19	76
		8	DSCP2	8
		80	AF22	80
		84	DSCP21	84
		88	AF23	88
		92	DSCP23	92
		96	CS3	96
	Default Value:	104

TOSMODEM	TOS for route via modem
	Type of Input:	single value, 3. parameter of a min-1-group
	Possible Values:	0	DF	0
		100	DSCP25	100
		104	AF31	104
		108	DSCP27	108
		112	AF32	112
		116	DSCP29	116
		12	DSCP3	12
		120	AF33	120
		124	DSCP31	124
		128	CS4	128
		132	DSCP33	132
		136	AF41	136
		140	DSCP35	140
		144	AF42	144
		148	DSCP37	148
		152	AF43	152
		156	DSCP39	156
		16	DSCP4	16
		160	CS5	160
		164	DSCP41	164
		168	DSCP42	168
		172	DSCP43	172
		176	DSCP44	176
		180	DSCP45	180
		184	EF	184
		188	DSCP47	188
		192	CS6	192
		196	DSCP49	196
		20	DSCP5	20
		200	DSCP50	200
		204	DSCP51	204
		208	DSCP52	208
		212	DSCP53	212
		216	DSCP54	216
		220	DSCP55	220
		224	CS7	224
		228	DSCP57	228
		232	DSCP58	232
		236	DSCP59	236
		24	DSCP6	24
		240	DSCP60	240
		244	DSCP61	244
		248	DSCP62	248
		252	DSCP63	252
		28	DSCP7	28
		32	CS1	32
		36	DSCP9	36
		4	DSCP1	4
		40	AF11	40
		44	DSCP11	44
		48	AF12	48
		52	DSCP13	52
		56	AF13	56
		60	DSCP15	60
		64	CS2	64
		68	DSCP17	68
		72	AF21	72
		76	DSCP19	76
		8	DSCP2	8
		80	AF22	80
		84	DSCP21	84
		88	AF23	88
		92	DSCP23	92
		96	CS3	96
	Default Value:	112

TOSPL	TOS payload value
	Type of Input:	single value, 3. parameter of a min-1-group
	Possible Values:	0	DF	0
		100	DSCP25	100
		104	AF31	104
		108	DSCP27	108
		112	AF32	112
		116	DSCP29	116
		12	DSCP3	12
		120	AF33	120
		124	DSCP31	124
		128	CS4	128
		132	DSCP33	132
		136	AF41	136
		140	DSCP35	140
		144	AF42	144
		148	DSCP37	148
		152	AF43	152
		156	DSCP39	156
		16	DSCP4	16
		160	CS5	160
		164	DSCP41	164
		168	DSCP42	168
		172	DSCP43	172
		176	DSCP44	176
		180	DSCP45	180
		184	EF	184
		188	DSCP47	188
		192	CS6	192
		196	DSCP49	196
		20	DSCP5	20
		200	DSCP50	200
		204	DSCP51	204
		208	DSCP52	208
		212	DSCP53	212
		216	DSCP54	216
		220	DSCP55	220
		224	CS7	224
		228	DSCP57	228
		232	DSCP58	232
		236	DSCP59	236
		24	DSCP6	24
		240	DSCP60	240
		244	DSCP61	244
		248	DSCP62	248
		252	DSCP63	252
		28	DSCP7	28
		32	CS1	32
		36	DSCP9	36
		4	DSCP1	4
		40	AF11	40
		44	DSCP11	44
		48	AF12	48
		52	DSCP13	52
		56	AF13	56
		60	DSCP15	60
		64	CS2	64
		68	DSCP17	68
		72	AF21	72
		76	DSCP19	76
		8	DSCP2	8
		80	AF22	80
		84	DSCP21	84
		88	AF23	88
		92	DSCP23	92
		96	CS3	96
	Default Value:	184

TYPE	Data type
	Type of Input:	single value, mandatory		(CHANGE,MTYPE=INITNCU2-Initialize NCUI2 board / CHANGE,MTYPE=NCUI2-NCUI2 board)
	Type of Input:	single value, optional		(DISPLAY,MTYPE=NCUI2-NCUI2 board / REGENERATE,MTYPE=NCUI2-NCUI2 board)
	Possible Values:	ALL	All data types	(CHANGE,MTYPE=INITNCU2-Initialize NCUI2 board)
		ASC	ASC Config Data
		DLSDATA	DLS Data
		DMCDATA	DMC specific data
		DSP	DSP Config Data
		GLOBAL	Boardspecific global data
		GWSECTOR	sector number of an IPDA-gateway	(CHANGE,MTYPE=NCUI2-NCUI2 board / DISPLAY,MTYPE=NCUI2-NCUI2 board / REGENERATE,MTYPE=NCUI2-NCUI2 board)
		H323	H.323 Config data
		IFDATA	Ethernet Interface
		IPCONF	IP configuration	(CHANGE,MTYPE=INITNCU2-Initialize NCUI2 board)
		IPCONF	ip configuration	(CHANGE,MTYPE=NCUI2-NCUI2 board / DISPLAY,MTYPE=NCUI2-NCUI2 board / REGENERATE,MTYPE=NCUI2-NCUI2 board)
		JB	adaptive jitter buffer
		LIDHFA	LAN interface data - HFA
		MANLANIF	Management LAN interface data
		MGNTDATA	Management Station and Back-Up Server
		SERVIF	Service Interface
		SIGQOS	QoS parameters for signalling
		SOCODATA	SoftGate Configuration data
		WANFD	WAN feature data
		WANIF	WAN interface data
		WBMDATA	WBM Login Data

UDPPRTHI	Parameter pre-provided, currently ineffective (automatically calculated by AMO, i.e. not changeable directly)
	Type of Input:	single value, 2. parameter of a min-1-group
	Possible Values:	numeric, 2023-65535
	Default Value:	CHANGE by MTYPE=INITNCU2: 30099 for the board with 60 b-channels and for the board with 120 b-channels

UDPPRTLO	Parameter pre-provided, currently ineffective
	Type of Input:	single value, 1. parameter of a min-1-group
	Possible Values:	numeric, 1024-64536
	Default Value:	CHANGE by MTYPE=INITNCU2: 29100

UIMODE	User Interface Mode
	Type of Input:	single value, 5. parameter of a min-1-group
	Possible Values:	CLASSIC	classical mode	DB_MUI_MODE_CLASSIC
		MAINTAIN	maintenance mode	DB_MUI_MODE_MAINTENANCE
		SECURITY	security mode	DB_MUI_MODE_SECURE
	Default Value:	security

VAD	Voice Activity Detection
	Type of Input:	single value, optional
	Possible Values:	NO	No	FALSE
	Possible Values:	YES	Yes	TRUE
	Default Value:	NO

VLAN	VLAN tagging on LAN-IF
	Type of Input:	single value, 1. parameter of a min-1-group
	Possible Values:	N	No	0
		NO	No	0
		Y	Yes	1
		YES	Yes	1
	Default Value:	NO

VLANID	VLAN-ID for VLAN-Tagging
	Type of Input:	single value, 4. parameter of a min-1-group
	Possible Values:	numeric, 0-4095
	Default Value:	0

WDEFRT	IP address of the default router within the LAN segment The default router takes care of routing forward all packets with a destination address with a network part different from the own LAN segment. 0.0.0.0 means that no default router is configured.
	Type of Input:	4 single values, concatenated with ., 5. parameter of a min-1-group
	Possible Values:	numeric, 0-255
	Default Value:	0.0.0.0 (no Default Router)

WIPADR	Source IP address of CGW board
	Type of Input:	4 single values, concatenated with ., 1. parameter of a min-1-group
	Possible Values:	numeric, 0-255
	Default Value:	0.0.0.0

WNETMASK	IP net mask of LAN segment The IP net mask determines the network and the host partition of an IP address. All IP addresses of a LAN segment must contain the identical network addresss part but different host address parts (also the Default Router must fulfill this requirement).
	Type of Input:	4 single values, concatenated with ., 2. parameter of a min-1-group
	Possible Values:	numeric, 0-255
	Default Value:	0.0.0.0

WPUBIP	Wan Public IP Address is communicated to the phone in the media handshake when a call is established.
	Type of Input:	4 single values, concatenated with ., 6. parameter of a min-1-group
	Possible Values:	numeric, 0-255
	Default Value:	0.0.0.0

WTLSP	HFA TLS Port
	Type of Input:	single value, 5. parameter of a min-1-group
	Possible Values:	numeric, 1024-65535
	Default Value:	4061

WTOSPL	TOS payload value
	Type of Input:	single value, 3. parameter of a min-1-group
	Possible Values:	0	DF	0
		100	DSCP25	100
		104	AF31	104
		108	DSCP27	108
		112	AF32	112
		116	DSCP29	116
		12	DSCP3	12
		120	AF33	120
		124	DSCP31	124
		128	CS4	128
		132	DSCP33	132
		136	AF41	136
		140	DSCP35	140
		144	AF42	144
		148	DSCP37	148
		152	AF43	152
		156	DSCP39	156
		16	DSCP4	16
		160	CS5	160
		164	DSCP41	164
		168	DSCP42	168
		172	DSCP43	172
		176	DSCP44	176
		180	DSCP45	180
		184	EF	184
		188	DSCP47	188
		192	CS6	192
		196	DSCP49	196
		20	DSCP5	20
		200	DSCP50	200
		204	DSCP51	204
		208	DSCP52	208
		212	DSCP53	212
		216	DSCP54	216
		220	DSCP55	220
		224	CS7	224
		228	DSCP57	228
		232	DSCP58	232
		236	DSCP59	236
		24	DSCP6	24
		240	DSCP60	240
		244	DSCP61	244
		248	DSCP62	248
		252	DSCP63	252
		28	DSCP7	28
		32	CS1	32
		36	DSCP9	36
		4	DSCP1	4
		40	AF11	40
		44	DSCP11	44
		48	AF12	48
		52	DSCP13	52
		56	AF13	56
		60	DSCP15	60
		64	CS2	64
		68	DSCP17	68
		72	AF21	72
		76	DSCP19	76
		8	DSCP2	8
		80	AF22	80
		84	DSCP21	84
		88	AF23	88
		92	DSCP23	92
		96	CS3	96
	Default Value:	184

WTOSSIGN	TOS, DiffServ Code Point for signalling for HFA
	Type of Input:	single value, 4. parameter of a min-1-group
	Possible Values:	0	DF	0
		100	DSCP25	100
		104	AF31	104
		108	DSCP27	108
		112	AF32	112
		116	DSCP29	116
		12	DSCP3	12
		120	AF33	120
		124	DSCP31	124
		128	CS4	128
		132	DSCP33	132
		136	AF41	136
		140	DSCP35	140
		144	AF42	144
		148	DSCP37	148
		152	AF43	152
		156	DSCP39	156
		16	DSCP4	16
		160	CS5	160
		164	DSCP41	164
		168	DSCP42	168
		172	DSCP43	172
		176	DSCP44	176
		180	DSCP45	180
		184	EF	184
		188	DSCP47	188
		192	CS6	192
		196	DSCP49	196
		20	DSCP5	20
		200	DSCP50	200
		204	DSCP51	204
		208	DSCP52	208
		212	DSCP53	212
		216	DSCP54	216
		220	DSCP55	220
		224	CS7	224
		228	DSCP57	228
		232	DSCP58	232
		236	DSCP59	236
		24	DSCP6	24
		240	DSCP60	240
		244	DSCP61	244
		248	DSCP62	248
		252	DSCP63	252
		28	DSCP7	28
		32	CS1	32
		36	DSCP9	36
		4	DSCP1	4
		40	AF11	40
		44	DSCP11	44
		48	AF12	48
		52	DSCP13	52
		56	AF13	56
		60	DSCP15	60
		64	CS2	64
		68	DSCP17	68
		72	AF21	72
		76	DSCP19	76
		8	DSCP2	8
		80	AF22	80
		84	DSCP21	84
		88	AF23	88
		92	DSCP23	92
		96	CS3	96
	Default Value:	104

WUDPPRTH	Parameter pre-provided, currently ineffective (automatically calculated by AMO, i.e. not changeable directly)
	Type of Input:	single value, 2. parameter of a min-1-group
	Possible Values:	numeric, 2023-65535
	Default Value:	CHANGE by MTYPE=INITNCU2: 30099 for the board with 60 b-channels and for the board with 120 b-channels

WUDPPRTL	Parameter pre-provided, currently ineffective
	Type of Input:	single value, 1. parameter of a min-1-group
	Possible Values:	numeric, 1024-65535
	Default Value:	CHANGE by MTYPE=INITNCU2: 29100

WVLAN	VLAN tagging on LAN-IF
	Type of Input:	single value, 3. parameter of a min-1-group
	Possible Values:	N	No	0
		NO	No	0
		Y	Yes	1
		YES	Yes	1
	Default Value:	NO

WVLANID	Virtual LAN Identification Special settings are required by certain LAN equipment (routers...), in other cases the VLAN Id should be set to 0 (default)
	Type of Input:	single value, 4. parameter of a min-1-group
	Possible Values:	numeric, 0-4095
	Default Value:	0

Error Messages

F03	F03: LTU <ltu> has not been assigned
F07	F07: <NCUI2> board data have <not \|already >been assigned.
F08	F08: Loadcommand PIT not successful: <loadresult>
F09	F09: The sum of the file lengths LENHHS, LENERR, LENSWT, LENTRC and LENEVT may not exceed <Max. value> kB. Please adjust the values.
F10	F10: The accounts LOGINTRM, LOGINPPP and LOGINWBM must not be identical.
F16	F16: No <NCUI2> board is assigned to AP shelf <ltu>.
F24	F24: The bandwidth limit (BANDW) has to be at least 1.2 times greater than the value for parameter MINTHRPT.
F25	F25: The sector @@@@ is already assigned to a gateway at pen @@-@@-@@@
F26	F26: <CUSIP\|SNETMASK> : @@@.@@@.@@@.@@@ is invalid
F27	F27: Entered parameter(s) must fit to rules of MINDLYV < AVGDLYV < MAXDLYV
F28	F28: Entered parameter(s) must fit to rules of AVGDLYD < MAXDLYD
F29	F29: PARAMETER CS1 OR CS2 CONTAINS A NOT PERMITTED CHARACTER ("BLANK", "/", "\").
F30	F30: CODEC CONFIGURATION NOT POSSIBLE BECAUSE OF FOLLOWING RESTRICTIONS : - G729 ONLY VAD=NO AND RTP SIZE 20, 30, 40, 50, 60, 70 AND 80 ALLOWED - G729A ONLY VAD=NO AND RTP SIZE 20, 30, 40, 50, 60, 70 AND 80 ALLOWED - G729B ONLY VAD=YES AND RTP SIZE 20, 30, 40, 50, 60, 70 AND 80 ALLOWED - G729AB ONLY VAD=YES AND RTP SIZE 20, 30, 40, 50, 60, 70 AND 80 ALLOWED
F31	F31: THE SPECIFIED CODEC MUST NOT BE USED TWICE. PLEASE REPLACE THE DOUBLE ENTRY AT PRIO@@ WITH VALUE "NONE" FIRST.
F32	F32: @@@@@@@@ must not be greater than @@@@@@@@ (@@@@@@@@ = @@@@@, @@@@@@@@ = @@@@@).
F34	F34: @@@@@@@@ = @@@@@ is not allowed. The lower bound of the UDP port range must be even.
F35	F35: UDPPORT HAS NOT BEEN CHANGED SINCE THERE IS AN OVELAPPING BETWEEN NEEDED IPDA PORTS AND UDPPORTS OF NCUIx BOARD LOCATED AT @@-@@-@@@. FOR DETAILS, CHECK VIA DISP-SIPCO;
F36	F36: No survivability is configured for this AP shelf, therefore SIGPTHSW=SURVONLY is not possible (check AMO-APRT TYP=SURV,KONF=AP).
F38	F38: DMC IS NOT SUPPORTED ON SOFT GATES (vNCUI). DMC parameters are not relevant , DMC needs to be configured at IP endpoints.
F39	F39: PARAMETER DMCALLWD CAN BE CHANGED ONLY WHEN THE SHELF IS DEACTIVATED. DEACT-USSU:,<ltu>;
F40	F40: LTU=0 is used only for TYPE=WBMDATA
F41	F41: IPV6 AND DHCP FUNCTIONALITY IS SUPPORTED ONLY FOR SOFTGATES.
F42	F42: The range between WUDPPRTL and WUDPPRTH must be at least 1, at most 999. (WUDPPRTL = @@@@@, WUDPPRTH = @@@@@).
F43	F43: For the codec OPUS only the ptime=10,20,40,60 ms are allowed.
F44	F44: STMIB NOT POSSIBLE FOR XEGW TRAILER.
F45	F45: THE COMBINATION OF NPE LICENSE WITH WIPADR AND/OR WPUBIP /= 0.0.0.0 IS NOT ALLOWED. PLEASE CHECK DISPLAY-CODEW;

Advisory Messages

H01	H01: For the specified NCUI board the branch is obsolete and will be ignored
H02	H02: No <Feature data> data found
H03	H03: <Feature data> data have been deleted
H04	H04: <Feature data> data have been changed
H05	H05: For the specified NCUI board 10 MBit/s is not allowed and will be ignored
H06	H06: In case of additionally activated feature SPE the total number of really usable b-channels will be reduced by some more again.
H07	H07: The default value of parameter BITRATE has been changed to 100MBFD because of HW related restrictions.
H08	H08: <Feature data> data have <not \|already >been assigned
H10	H10: The <Feature data> data are uploaded during the transition of the board into the 'READY' state.
H11	H11: Changed Board data existing - NCUI2 board should be loaded by means of EXEC-USSU:UPDATAP,<ltu>;
H12	H12: Dynamic board is not available. Board data have not been loaded
H13	H13: Board not "ready". Board data have not been loaded
H14	H14: <Feature data> Board data have been loaded to LTU @@.
H15	H15: The two lowest bits of at least one Tos values have been reset to zero
H16	H16: For the actual board the parameter DMCCONN can not exceed the total number of @@@ possible DMC connections (b-channels). The parameter DMCCONN has been corrected to this value. In case of additionally activated feature SPE the total number of really usable b-channels will be reduced by some more again.
H17	H17: For A-Law the parameter PATTERN must have the value 213 (H'D5), for U-LAw the value must be set to 255 (H'FF).
H18	H18: The board requires the setting BITRATE=100MBFD to guarantee proper. operation. All other settings can lead to heavy troubles in the IP network(e.g.: Half ways, cross talks, etc.)
H22	H22: The changed parameters "MINDLYV" and/or "PACKLOSS" have no effect until JBMODE is set to: 2[ADAPTIVE].
H24	H24: JB parameters can not be changed unless DAJB is not set by means of CHA-ZANDE:TYPE=ALLDATA,DAJB=NO;
H25	H25: Sector number already configured for entered gateway.
H26	H26: @@@@ is preferred for outgoing DMC-calls.
H27	H27: Only codec @@@@ is supported.
H32	H32: Switch over of signalling connection has been initiated. ( For current state of signalling connection see DISP-UCSU )
H33	H33: Default values of UDP Port for NCUIx board is adjusted according to UDPPORT value in AMO-SIPCO. UDPPRTLO value for NCUIx board is set to @@@@@ which is just after IPDA UDP port range.
H34	H34: THE BRANCH SOCODATA IS NOT RELEVANT FOR TRADITIONAL HW SHELVES AND WILL BE IGNORED.
H35	H35: The T38FAX is not yet supported on NCUI boards, the default value has been set internally.
H36	H36: Changed board data - Requires manual board restart: RES-USSU:LTU,<ltu>;
H39	H39: The range between UDPPRTLO and UDPPRTHI must be at least @@@. Parameters are set internally as UDPPRTLO = @@@@@, UDPPRTHI = @@@@@.
H40	H40: All HG3575 Boards will be updated with this data.
H41	H41: The parameter UDPPRTHI is read only. It will be ignored. It will be set to UDPPRTLO + 999.
H42	H42: Bandwidth limitation is causing huge delays during NCUI upgrade/installation!
H43	H43: Please note that IPv6 tunneling for CC<->AP communication is not fully supported yet(in Release 1).
H44	H44: Please note that DHCP functionality is not fully supported yet.
H45	H45: THE BRANCHES WANIF AND WANFD ARE NOT RELEVANT FOR TRADITIONAL HW SHELVES AND WILL BE IGNORED.
H46	H46: WANIF AND WANFD DATA EXISTS ONLY FOR SOFTGATES.
H47	H47: PARAMETER BITRATE IS IGNORED FOR THIS SHELF TYPE. SETTINGS CAN BE ADJUSTED VIA XML IF NEEDED.
H48	H48: JITBUFD Parameter is no longer used and will be ignored.
H50	H50: The branch H323 is no longer used and will be ignored.
H51	H51: YOU MUST ENSURE THE NETWORK SIDE IS CONFIGURED WITH THE SAME DUPLEX/BITRATE SETTINGS TO AVOID FUNDAMENTAL VOIP PROBLEMS (DUPLEX MISMATCH).
H52	H52: The specified codec must not be used twice. The codec of Prio@@ is replaced with value 'NONE'.
H53	H53: ATTN: After a change of MIPADR a new HG3550M Assistant backup set is required.
H54	H54: default value for all softgates see disp-zande:licdata;
H55	H55: individual value for softgate set
H56	H56: individual value for softgate removed
H57	H57: MGNTIP, MGNTPN, BUSIP & BUSPN ARE IGNORED AND DERIVED FROM AMO SIPCO
H58	H58: DATA FOR XEGW TRAILER WILL BE UPDATED IMPLICITLY.