202.4.2 Advisories


H03:	ADD DATA FOR <bbb> <xxxx> WITH AMO CONSY
H04:	DELETE DATA FOR <bbb> <xxxx> WITH AMO CONSY
H06:	THE EXISTING OVERLAY CONFIGURATION WAS <action>
H07:	<aaa> <xxxx> DELETED
H08:	LTG <xx> ADDED (NL)
H09:	THE NEW OVERLAY CONFIGURATION HAS BEEN ASSIGNED. PLEASE MOUNT THE HWY-CABLE OF OVERLAY LTU <xx> TO STANDARD LTU <xx>. THE NEW OVERLAY HWYS CAN BE CHECKED VIA AMO TSU IN THE SAME WAY AS THE NORMAL HWYS FOR STANDARD LTUS.
H09:	THE NEW OVERLAY CONFIGURATION HAS BEEN ASSIGNED. THE NEW OVERLAY HWYS CAN BE CHECKED VIA AMO TSU IN THE SAME WAY AS THE NORMAL HWYS FOR STANDARD LTUS.
H10:	<aaa> <xxxx> ALREADY DELETED
H11:	THE STATUS OF AT LEAST ONE OVERLAY HWY IS DEFECT. PLEASE INITIATE A HARDRESTART OF THE SWU AFTER SAVING THE CHANGED CONFIGURATION VIA AMO UPDAT.
H12:	THE AP SPECIFIC TONE AND ANNOUNCEMENT PARAMETERS HAVE TO BE LOADED MANUALLY. THIS CAN BE DONE BY MEANS OF COMMAND EXEC-USSU:NCUILOAD NOTE: CHANGES OF CP TONES MAY WORK IMMEDIATELY, BUT MANUAL LOADING IS STILL REQUIRED.
H13:	THE ACTUAL LTUC BOARD HAS <xx> MOUNTED CBM MODULES BUT FOR ONLY <xx> MODULES CONFIGURATION VALUES HAVE BEEN SPECIFIED. THE REMAINING MODULES WILL BE CONFIGURED WITH DEFAULT VALUE EC64.
H15:	PARAMETER APRTADDR CAN NOT BE CHECKED FOR A PLAUSIBLE VALUE. THIS CHECK WILL BE DONE LATER WITHIN AMO-APRT.
H16:	PARAMETER <param> IGNORED
H17:	PARAMETER <param> HAS NOT BEEN SPECIFIED, THEREFORE THE DEFAULT ROUTER ADDRESS <ip1.ip2.ip3.ip4> HAS BEEN ASSIGNED.
H18:	THE CHANGE TAKES EFFECT NOT BEFORE THE AFFECTED NCUI BOARD IS RESTARTED (EXEC-USSU:MODE=UPDATAP)
H19:	NO CONFIGURED DATA FOUND FOR ENTERED VALUE(S).
H20:	THE AMOUNT OF AVAILABLE B-CHANNELS ON NCUI/NCUI2 BOARD HAS BEEN CHANGED ! PLEASE CHECK THE CONFIGURATION (ALSO AMO-STMIB)
H21:	IF THE PARAMETER BCHLCNT IS SPECIFIED, THE AMOUNT OF AVAILABLE B-CHANNELS ON NCUI/NCUI2 BOARD IS SMALLER AS THE DEFAULT VALUE OF THE BOARD ! THE RESOURCE MANAGEMENT IS ALSO AFFECTED BY SPECIFIYING THIS PARAMETER, THEREFORE ONLY <xxx> B-CHANNELS WILL BE CONFIGURED.
H22:	SPE NOT ACTIVATED, NO SPE RESULT STATE INFORMATION AVAILABLE.
H23:	SINCE PAYLOAD ENCRPTION AND/OR DMC IS ENABLED, THE NUMBER OF B-CHANNELS HAS BEEN REDUCED BY @@@ B-CHANNELS DUE TO HIGH PERFORMANCE NEEDS.
H24:	THE SETTING OF PARAMETER BITRATE HAS BEEN CHANGED TO 100MBFD BECAUSE OF HW RELATED RESTRICTIONS. CHANGE POSSIBLE WITH AMO-STMIB.
H25:	THE PARAMETERS SOCOTYPE, IPMODE, DHCPV4 AND DHCPV6 ARE NOT RELEVANT FOR TRADITIONAL HW SHELVES AND WILL BE IGNORED.
H26:	UBGDAT ENTRY HAS BEEN MODIFIED INTERNALLY BEFORE FIRST USAGE.
H27:	SPE ON: TO GET THE SHELF FINALLY INTO SERVICE, FOLLOWING STEPS ARE NEEDED: -ENTER A MEK VIA THE @@@@@@@@@@@@@@@@@@@@@@ -AFTERWARDS ENTER THIS MEK VIA “MEK Administration Client” (Assistant)
H28:	PLEASE NOTE THAT IPV6 TUNNELING FOR CC<->AP COOMUNICATION IS NOT FULLY SUPPORTED YET (IN RELEASE 0).
H29:	PLEASE NOTE THAT DHCP FUNCTIONALITY IS NOT FULLY SUPPORTED YET (IN RELEASE 0).
H30:	Multiple entry of <textsel> has been ignored.
H31:	THE CHANGE TAKES EFFECT NOT BEFORE THE AFFECTED AP SHELF IS RESTARTED (RES-USSU).
H32:	SOCO50 IS RECOMMENDED FOR VIRTUAL MACHINES WITH ONLY 2 CPU CORES. SOCO1000 IS RECOMMENDED FOR 4 CPU CORES OR MORE. SOCO500 IS NO LONGER USED.
H33:	SOCOTYPE AUTOMATICALLY CHANGED TO SOCO1000

OpenScape 4000 V10, Volume 1: AMO Descriptions, Service Documentation, Issue 5, ID: P31003H31A0S107057620

© 09/2025 Mitel Networks Corporation. - All rights reserved.
Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG. All other trademarks herein are the property of their respective owners.