AUN - Call Pickup Groups

Call pickup groups are groups of stations in which each station can accept calls for the other stations in the group.

Call pickup groups can be created independently of internal traffic groups (ITR groups). However, a call can be picked up only if the inter-ITR group traffic between the calling and the accepting station is permitted.

Analog and digital telephones can form a call pickup group in any combination. The call pickup between these stations is not restricted.

A pickup group comprises at least 1 station which is configured at the same node as the pickup group. In addition, the local group can be merged with remote groups being configured at remote remote nodes which support network wide pickup groups. Such a configuration is called Networkwide Pickup Group . The remote groups are specified by so called 'Remote Links'.

ONS(One Number Service)groups are groups of stations where an incoming call is to be signalled at more than one destination in parallel and where an incoming call is blocked by busy, if one station of the parallel ringing station group is busy.

Analog and digital phones including IP phones, CMI cordless phones and GSM mobile phones can form an ONS group.

The group members of a Parallel Ringing,ONS, group are always located in the same node except one GSM phone which is located in an external network.

Some Points to Note:

A maximum of 2000 local call pickup/ONS groups is possible in one node.

A call pickup group can contain in summary up to a maximum of 255 stations and remote links.

An ONS group can contain in summary up to a maximum of 255 stations and remote access code.

A station can be a member of only one call pickup/ONS group.

All stations in a call pickup/ONS group can be digital voice terminals (DIGITEs). For PU groups,the signaling mode is configurable due to the number of DIGITEs. Recommended is:

For less than 25 DIGITE's: SIGNAL=ALL,

For 26-75 DIGITE's: SIGNAL=LED,

For more than 75 DIGITE's: SIGNAL=NONE

Flexible Memory Management: It is advantageous to use low group numbers in ADD-Command (or omit the parameter GRNO). That is because the group number is stored as maximum used group number and it is not possible to reduce the DIMSU-Parameter PUGR below this value.

For each remote link DIMSU memory is needed (REMPUG).

Functional voice terminals (SET600, functional point to point connections), primary and secondary station numbers of a bus or OPTISET-connection and MSN ( Multiple Subscriber Numbers ) are allowed in a call pickup/ONS group.

A MSN correlated to a bus- or OPTISET-connection without a functional voice terminal (SET600) cannot be added to a call pickup group.

The executive and secretary stations of an integrated executive/secretary telephone system may not both be members of the same call pickup/ONS group.

For every call pickup group a call park option is created.

When deleting DIGITEs, or a PU group with call park option, all parked calls are cleared. This is done by physically deactivating and then reactivating the 'parked' party's station.

When adding stations to or deleting stations from a PUGR, the AMO doesn't block the call pickup feature (as it was in earlier versions). It doesn't wait for pickup waiting queue getting empty, therefore new calls will not slow down the AMO execution.

Forced station number display for all emergency calls is optional for each PU group. The type of delay notification can also be set.

Certain special subscribers configured by AMO SSCSU (e.g. extension lines or "Hicom Trading Board"-Manager) are rejected as pickup group members.

Remote stations are connected via Remote Links . In detail, a local PU group (GRNO) is merged with a remote PU group (REMGRNO) residing at a remote node (REMAC). It must be considered that only whole groups and no single stations can be linked together. The appropriate linkage must always be defined in both directions (own -> remote node, remote -> own node).

In a local group only 1 Remote Link to a specific node can be configured. A remote link is identified by a remote access code and a remote pu group number. The physical node access code (AMO ZAND, parameter PNODECD) has to be used.

One or more PU groups can be embedded in a network wide team functionality. This is configured by assigning a Team Number (TEAMNO) to it. At least one member of such a PU group must be prepared for team functionality, that means it must have got one of the attributes TEAMEXEC or TEAMSECR. In addition, there are some restrictions to be obeyed for PU groups with team functionality:

PU groups (with TEAMNO) are to be added and deleted using one user command. Subsequently a group cannot be enlarged or reduced by team members

A PU group (with TEAMNO) can be only deleted if all team members have been immediately deactivated (hard locked)

Note:

SDAT

Fictitious PU groups, that means for Networking reserved PU groups (NWRES=YES), are only used for transporting signaling informations between nodes in a network and therefore have no pickup functionality. Per node only one fictitious PU group is configurable. Beside the Remote Links, a PU group which is reserved for Networking must contain one and only one Floating Station.

Note:

Each ONS group must have one master phone and which is defined by AMO-SDAT. The other stations-if exist- must be defined as secondary phone by AMO-SDAT.

ONS group for CHESE members is not supported.

ONS group members cannot be members of call pickup groups. Moving between PU group to ONS group and vice versa is not supported.

ONS group members cannot be assigned to different ITR groups.

ONS group members cannot be nightstations.

Secondary phone of an ONS group cannot be member or master of a hunting group(SA). Master phone of an ONS group cannot be master of a hunting group, whereas it can be secondary phone of a hunting group.

ONS master and ONS secondary extension numbers must not appear on any other keyset.

ONS group must have only one Remote Access Code

Cross Reference to Other AMOs:

AMO DIMSU	:	Dimensioning of Features
AMO SBCSU	:	Station and S0-Bus Configuration of SWU
AMO SDAT	:	Prepare stations for team functionality
AMO SSCSU	:	Configuration of special subscribers
AMO ZAND	:	Configuration of own physical node access code

Destination Processor: BP (Switching Unit)

Functions

ADD	Create and expand a call pickup group	password class 2
CHANGE	Change the attributes of call pickup groups	password class 2
DELETE	Cancel (members of) call pickup groups	password class 2
DISPLAY	Interrogate call pickup groups	password class 0
REGENERATE	Regenerate call pickup groups	password class 2

Procedure Overview

ADD-AUN

ADD-AUN	{(max 1) GRNO=<number>, GRSTNO=<number>},
		TYPE=GR, {(min 1) STNO=<number>, REMAC=<key-num>, REMGRNO=<number>}, [DISTNO=<param>], [NOTRNG=<param>], [PUSECOND=<param>], [SIGNAL=<param>], [REMSIGO=<param>], [REMSIGI=<param>], [REMSIGPK=<param>], {(max 1) TEAMNO=<number>, NWRES=<param>};
		TYPE=ONS, {(min 1) STNO=<number>, REMAC=<key-num>}, [PUSECOND=<param>], [SMPF=<param>], [ONSSNS=<param>];

If a specified PU/ONS group does not exist, it is assigned with the specified stations and remote links/remote access code.

If it is already entered, the existing PU/ONS group is expanded to include the specified stations and remote links/remote access code.

A group can be specified by a group number (GRNO) or by a station number of a group member (GRSTNO). If none of these parameters is specified, the AMO creates the first available group in system.

If the station number / remote link (STNO/REMAC) is already member of another PU/ONS group, it is moved to the new/enlarged PU/ONS group.

STNO, REMAC and REMGRNO belong to a parameter PU group with condition MIN=1.

STNO and REMAC belong to a parameter ONS group with condition MIN=1.

For PU groups, REMAC and REMGRNO must be both specified in command.

STNO and GRSTNO must not be specified both.

A group must contain at least 1 STNO. The upper limit is in summary 255 STNO's / Remote Links.

With 1 command only 1 Remote Link/Remote Access Code can be added to a PU/ONS group.

If an ONS group is created with only one member,this station must be the master of ONS group. In this case,each other entered station must be defined as secondary by AMO-SDAT.

If an ONS group is created with more than one member, one of them should be already defined as master and others should be already defined as secondary by AMO-SDAT.

If ONS group tried to be created with more than three analog or digital device configuration, advisory message should be given to inform user:

H30: ONLY FIRST THREE MEMBERS OF THE ONS GROUP WILL BE CONSIDERED.

ONS group members cannot be members of call pickup groups. Moving between PU group and ONS is not supported.

Master of a hunting group is not allowed to be member of an ONS group.

Member of a hunting group is not allowed as secondary of an ONS group.

Examples:

Assign PU group 100 with stations 2104, 2105, 2106.

Input:

ADD-AUN:GRNO=100,TYPE=GR,STNO=2104&&2106;

Output:

H13: THE PICKUP GROUP WORKS WITH SIGNALING MODE ALL (DEFAULT VALUE)

H03: PU GROUP 100 CREATED WITH: NUMBER OF STNO'S: 3, NUMBER OF REMOTE LINKS: 0

Expand PU group 100 by station 3104 and a remote link to PU group 5 (node access code = 91).

Input:

ADD-AUN:GRNO=100,TYPE=GR,STNO=3104,REMAC=91,REMGRNO=5;

Output:

H12: THE REMOTE LINK HAS BEEN ENTERED IN PU GROUP. PLEASE ENTER COMMANDAT REMOTE NODE (AMO ZAND, PNODECD=91):ADD-AUN:GRNO=5,REMAC=92,REMGRNO=100;

H01: PU GROUP 100 EXTENDED BY:NUMBER OF STNO'S: 1, NUMBER OF REMOTE LINKS: 1

Move station 2104 from its pickup group (e.g. 100) to a group, where already station 3100 resides (e.g. 8).

Input:

ADD-AUN:GRSTNO=3100,TYPE=GR,STNO=2104;

Output:

H18: STNO 2104 MOVED FROM PU GROUP 100 TO PU GROUP 8

H01: PU GROUP 100 EXTENDED BY:NUMBER OF STNO'S: 1, NUMBER OF REMOTE LINKS: 0

Assign ONS group 10 with stations 2130 which is defined as master by AMO-SDAT.

Input:

ADD-AUN:GRNO=10,TYPE=ONS,STNO=2130;

Output:

H35: ONS GROUP 10 CREATED WITH: NUMBER OF STNO'S: 1, NUMBER OF REMAC: 0

H36: ONS GROUP WITH GRNO 10 CONTAINS ONLY 1 STATION

Expand ONS group 10 by station 2129,which is defined as secondary by AMO-SDAT, and a remote access code 91094643826 .

Input:
```
ADD-AUN:GRNO=10,TYPE=ONS,STNO=2129,REMAC=91094643826 ;
```
Output:
```
H34: ONS GROUP 10 EXTENDED BY:NUMBER OF STNO'S: 1, NUMBER OF REMAC: 1
```

Assign ONS group 11 with stations 2131,2124,2126 and a remote access code 9998887776.

Input:

ADD-AUN:GRNO=11,TYPE=ONS,STNO=2131&2124&2126,REMAC=9998887776;

Output:

H30: ONLY FIRST THREE MEMBERS OF THE ONS GROUP WILL BE CONSIDERED.

H35: ONS GROUP 11 CREATED WITH: NUMBER OF STNO'S: 3, NUMBER OF REMAC: 1

CHANGE-AUN

CHANGE-AUN
		TYPE=GR,GRNO=<number>, {(min 1) DISTNO=<param>, NOTRNG=<param>, PUSECOND=<param>, SIGNAL=<param>, TEAMNO=<number>};
		TYPE=REM,GRNO=<number>, REMAC=<key-num>, {(min 1) REMSIGO=<param>, REMSIGI=<param>, REMSIGPK=<param>};
		TYPE=ONS,GRNO=<number>, {(min 1) PUSECOND=<param>, SMPF=<param>, ONSSNS=<param>, REMAC=<key-num>};

Change the attributes of call pickup/ONS groups

Change the attributes of remote links

Examples:

Change group specific attributes(PU):

Input:

CHANGE-AUN:TYPE=GR,GRNO=100,NOTRNG=PERIOD3,SIGNAL=LED;

Output:

H13: THE PICKUP GROUP WORKS WITH SIGNALING MODE LED (DIFFERENT FROM DEFAULT VALUE)

Change the remote link specific attributes(PU):

Input:
```
CHANGE-AUN:TYPE=REM,GRNO=100,REMAC=91,REMSIGPK=N;
```

Integrate a PU group subsequently into the network wide team with Team Number 5 (at least 1 member must have the TEAMEXEC or TEAMSECR attribute):

Input:
```
CHANGE-AUN:TYPE=GR,GRNO=99,TEAMNO=5;
```

Note:

Change group specific attributes(ONS):

Input:

CHANGE-AUN:TYPE=ONS,GRNO=10,SMPF=YES,ONSSNS=YES;

Change the remote access code (ONS):

Input:
```
CHANGE-AUN:TYPE=ONS,GRNO=10,REMAC=9132;
```

DELETE-AUN

DELETE-AUN
		TYPE=SYS;
		TYPE=GR,GRNO=<number>;
		TYPE=STN,[GRNO=<number>], STNO=<number>;
		TYPE=REM,GRNO=<number>, REMAC=<key-num>;
		TYPE=NWRES;

The following can be deleted:

All the PU/ONS groups of a system

A specific PU/ONS group

Specific stations of PU/ONS groups. The group number can but must not be specified.

A specific remote link/remote access code from a specific PU/ONS group

The fictitious, for Networking reserve PU group

Examples:

Remove station 2105 from PU group 100

Input:

DEL-AUN:TYPE=STN,GRNO=100,STNO=2105;

Output:

H20: STNO 2105 DELETED FROM PICKUP GROUP 100

or:

DEL-AUN:TYPE=STN,STNO=2105;

Output:

H20: STNO 2105 DELETED FROM PICKUP GROUP 100

Remove the remote link to node 91 from PU group 100:

Input:

DEL-AUN:TYPE=REM,GRNO=100,REMAC=91;

Output (own node access code = 92):

H16: THE REMOTE LINK HAS BEEN DELETED. PLEASE DELETE AT REMOTE NODE (AMO ZAND, PNODECD=91) ALSO THE CORRESPONDING LINK BY: DEL-AUN:TYPE=REM,GRNO=5,REMAC=92;

For ONS groups, master phone can only be deleted after deletion of all secondary devices:

Remove station 2129 from ONS group 10:

Input:

LOE-AUN:TYPE=STN,GRNO=10,STNO=2129;

Output:

H20: STNO 2129 DELETED FROM GROUP 10

H17: PU GROUP WITH GRNO 10 CONTAINS ONLY 1 STATION.

Remove station 2130 from ONS group 10:

Input:

LOE-AUN:TYPE=STN,GRNO=10,STNO=2130;

Output:

H20: STNO 2130 DELETED FROM GROUP 10

H02: GROUP WITH GRNO 10 DELETED.

Remove the remote access code 9998887776 from ONS group 11:

Input:
```
DEL-AUN:TYPE=REM,GRNO=11,REMAC=9998887776;
```

DISPLAY-AUN

DISPLAY-AUN
		[TYPE=SYS];
		[TYPE=GR],GRNO=<number>;
		[TYPE=STN],STNO=<number>;
		[TYPE=REM],[REMAC=<key-num>];
		[TYPE=TEAM],[TEAMNO=<number>];
		[TYPE=ONS];

The following can be displayed:

All the PU and ONS groups of a system

A specific PU/ONS group

PU/ONS groups containing specific stations

The PU group containing a specific remote link,all PU groups with remote links

All PU groups which are integrated in any network wide team or the PU group(s) which is (are) integrated in a specific network wide team

Example

Interrogate PU group 1

Input:

DIS-AUN:GRNO=1;

Output:

 +---------------------------------------------------------------------------+
 | GROUP NO.:           1          TEAM NUMBER:        123                   |
 |                                 NW-RESERVED:        N                     |
 |                                                                           |
 | A-PARTY NO.DISPLAY:  N          NOTIFICATION RING:  ON3                   |
 | PU SECOND CALL:      N          SIGNALING MODE:     ALL                   |
 |                                                                           |
 | SUBSCRIBERS:    2100 -   2102                                             |
 +---------------------------------------------------------------------------+

Interrogate all PU groups with at least 1 remote link:

Input:

DIS-AUN:TYPE=REM;

Output:

 +---------------------------------------------------------------------------+
 | GROUP NO.:           2          TEAM NUMBER:                              |
 |                                 NW-RESERVED:        N                     |
 |                                                                           |
 | A-PARTY NO.DISPLAY:  Y          NOTIFICATION RING:  ON3                   |
 | PU SECOND CALL:      N          SIGNALING MODE:     LED                   |
 |                                                                           |
 | SUBSCRIBERS:    2100 -   2102                                             |
 |                 2125 -   2129                                             |
 |                 3500                                                      |
 |                 3501                                                      |
 | REMOTE LINKS:        REMAC  REMGRNO   REMSIGO   REMSIGI   REMSIGPK        |
 |                        333        5         Y         N          Y        |
 |     1234567890123456789012      999         Y         Y          Y        |
 |                      55555       66         N         Y          N        |
 +---------------------------------------------------------------------------+
 +---------------------------------------------------------------------------+
 | GROUP NO.:           5          TEAM NUMBER:                              |
 |                                 NW-RESERVED:        Y                     |
 |                                                                           |
 | A-PARTY NO.DISPLAY:  N          NOTIFICATION RING:  ON3                   |
 | PU SECOND CALL:      N          SIGNALING MODE:     ALL                   |
 |                                                                           |
 | SUBSCRIBERS:    2200                                                      |
 | REMOTE LINKS:        REMAC  REMGRNO   REMSIGO   REMSIGI   REMSIGPK        |
 |                        999        9         Y         Y          Y        |
 +---------------------------------------------------------------------------+

Display all ONS groups:

Input:

DIS-AUN:TYPE=ONS;

Output:

 +---------------------------------------------------------------------------+
 | GROUP NO.:           8                                                    |
 |                                                                           |
 | PU SECOND CALL:      NO                                                   |
 | ONS :  YES          SMPF :   NO         ONSSNS :   NO                     |
 |                                                                           |
 | SUBSCRIBERS:    3149          (MASTER)                                    |
 +---------------------------------------------------------------------------+
 +---------------------------------------------------------------------------+
 | GROUP NO.:           10                                                   |
 |                                                                           |
 | PU SECOND CALL:      NO                                                   |
 | ONS :  YES          SMPF :  YES         ONSSNS :  YES                     |
 |                                                                           |
 | SUBSCRIBERS:    3156          (MASTER)                                    |
 | REMAC:  34                                                                |
 +---------------------------------------------------------------------------+
 +---------------------------------------------------------------------------+
 | GROUP NO.:           30                                                   |
 |                                                                           |
 | PU SECOND CALL:      NO                                                   |
 | ONS :  YES          SMPF :   NO         ONSSNS :  YES                     |
 |                                                                           |
 | SUBSCRIBERS:    3119          (MASTER)                                    |
 |                 3118                                                      |
 +---------------------------------------------------------------------------+

REGENERATE-AUN

REGENERATE-AUN
		[TYPE=SYS];
		[TYPE=GR],GRNO=<number>;
		[TYPE=STN],STNO=<number>;
		[TYPE=REM],[REMAC=<key-num>];
		[TYPE=TEAM],[TEAMNO=<number>];
		[TYPE=ONS];

The following can be regenerated:

All the PU und ONS groups of a system

A specific PU/ONS group

PU/ONS groups containing specific stations

The PU group containing a specific remote link,all PU groups with remote links

All PU groups which are integrated in any network wide team or the PU group(s) which is (are) integrated in a specific network wide team

Example:

Regeneration of a PU group with GRNO 1

Input:

REG-AUN:GRNO=1;

Output:

ADD-AUN:1,,GR,2100&&2102,,,N,ON3,N,ALL,,,,123,N;

Regeneration of a PU group comprising a remote link to node 999:

Input:

REG-AUN:REMAC=999;

Output:

ADD-AUN:5,,GR,2200,,,N,ON3,N,ALL,,Y;

ADD-AUN:5,,GR,,999,9,,,,,Y,Y,Y,,;

Regenerate all ONS groups:

Input:

REG-AUN:TYPE=ONS;

Output:

ADD-AUN:GRNO=8,TYPE=ONS,STNO=3149,PUSECOND=NO,SMPF=NO,ONSSNS=NO;

ADD-AUN:GRNO=10,TYPE=ONS,STNO=3156,PUSECOND=NO,SMPF=YES,ONSSNS=YES;

ADD-AUN:GRNO=10,TYPE=ONS,REMAC=34;

ADD-AUN:GRNO=30,TYPE=ONS,STNO=3119&3118,PUSECOND=NO,SMPF=NO,ONSSNS=YES;

Parameter description

DISTNO	display station no. of calling party
	Type of Input:	single value, 1. parameter of a min-1-group			(CHANGE,TYPE=GR-group)
	Type of Input:	single value, optional			(ADD,TYPE=GR-group)
	Possible Values:	NO	no	FALSE
	Possible Values:	YES	yes	TRUE
GRNO	pickup group number
	Type of Input:	1 to 16 single values, concatenated with & or &&, mandatory			(DISPLAY,TYPE=GR-group / REGENERATE,TYPE=GR-group)
		single value, 1. parameter of a max-1-group			(ADD)
		single value, mandatory			(CHANGE,TYPE=GR-group / CHANGE,TYPE=ONS-One number service / CHANGE,TYPE=REM-remote link / DELETE,TYPE=GR-group / DELETE,TYPE=REM-remote link)
		single value, optional			(DELETE,TYPE=STN-station)
	Possible Values:	numeric, 1-2000
GRSTNO	pu group which contains this station
	Type of Input:	single value, 2. parameter of a max-1-group
	Possible Values:	numeric, up to 12 characters
NOTRNG	delayed notification tone ring (e.g. call waiting)
	Type of Input:	single value, 2. parameter of a min-1-group			(CHANGE,TYPE=GR-group)
	Type of Input:	single value, optional			(ADD,TYPE=GR-group)
	Possible Values:	OFF	no notification	DB_AUFM_RUF_NZ_OHNE
		ON1	with single burst notification in all states	DB_AUFM_RUF_NZ_1_MIT
		ON3	with multiple burst notification in all states	DB_AUFM_RUF_NZ_3_MIT
		ONIDLE1	single burst notification only in idle state	DB_AUFM_RUF_NZ_1_RUHEZUST
		ONIDLE3	multiple burst notification only in idle state	DB_AUFM_RUF_NZ_3_RUHEZUST
		PERIOD1	with single burst periodical notification	DB_AUFM_RUF_NZ_1_REP
		PERIOD3	with multiple burst periodical notification	DB_AUFM_RUF_NZ_3_REP
NWRES	for networking reserved fictive pu group
	Type of Input:	single value, 2. parameter of a max-1-group
	Possible Values:	NO	no	FALSE
	Possible Values:	YES	yes	TRUE
ONSSNS	Suppress ONS Slave Number upon answer from Slave
	Type of Input:	single value, 3. parameter of a min-1-group			(CHANGE,TYPE=ONS-One number service)
	Type of Input:	single value, optional			(ADD,TYPE=ONS-One number service)
	Possible Values:	NO	no	FALSE
	Possible Values:	YES	yes	TRUE
PUSECOND	pick up of second call enabled
	Type of Input:	single value, 1. parameter of a min-1-group			(CHANGE,TYPE=ONS-One number service)
		single value, 3. parameter of a min-1-group			(CHANGE,TYPE=GR-group)
		single value, optional			(ADD,TYPE=GR-group / ADD,TYPE=ONS-One number service)
	Possible Values:	NO	no	FALSE
	Possible Values:	YES	yes	TRUE
REMAC	remote access code
	Type of Input:	single value, 2. parameter of a min-1-group			(ADD,TYPE=GR-group / ADD,TYPE=ONS-One number service)
		single value, 4. parameter of a min-1-group			(CHANGE,TYPE=ONS-One number service)
		single value, mandatory			(CHANGE,TYPE=REM-remote link / DELETE,TYPE=REM-remote link)
		single value, optional			(DISPLAY,TYPE=REM-remote link / REGENERATE,TYPE=REM-remote link)
	Possible Values:	0-9,*,#,A-D, up to 22 characters
REMGRNO	remote group number
	Type of Input:	single value, 3. parameter of a min-1-group
	Possible Values:	numeric, 1-2000
REMSIGI	remote signaling incoming
	Type of Input:	single value, 2. parameter of a min-1-group			(CHANGE,TYPE=REM-remote link)
	Type of Input:	single value, optional			(ADD,TYPE=GR-group)
	Possible Values:	NO	no
	Possible Values:	YES	yes
REMSIGO	remote signaling outgoing
	Type of Input:	single value, 1. parameter of a min-1-group			(CHANGE,TYPE=REM-remote link)
	Type of Input:	single value, optional			(ADD,TYPE=GR-group)
	Possible Values:	NO	no
	Possible Values:	YES	yes
REMSIGPK	remote signaling for parking
	Type of Input:	single value, 3. parameter of a min-1-group			(CHANGE,TYPE=REM-remote link)
	Type of Input:	single value, optional			(ADD,TYPE=GR-group)
	Possible Values:	NO	no
	Possible Values:	YES	yes
SIGNAL	signaling mode
	Type of Input:	single value, 4. parameter of a min-1-group			(CHANGE,TYPE=GR-group)
	Type of Input:	single value, optional			(ADD,TYPE=GR-group)
	Possible Values:	ALL	display, led and tone signaling	DB_GPU_LOCAL_SIG_FULL
		LED	only led signaling	DB_GPU_LOCAL_SIG_LED_ONLY
		NONE	no signaling	DB_GPU_LOCAL_SIG_NONE
SMPF	Search mobile phone first
	Type of Input:	single value, 2. parameter of a min-1-group			(CHANGE,TYPE=ONS-One number service)
	Type of Input:	single value, optional			(ADD,TYPE=ONS-One number service)
	Possible Values:	NO	no	FALSE
	Possible Values:	YES	yes	TRUE
STNO	station number
	Type of Input:	1 to 16 single values, concatenated with & or &&, 1. parameter of a min-1-group			(ADD,TYPE=GR-group / ADD,TYPE=ONS-One number service)
	Type of Input:	1 to 16 single values, concatenated with & or &&, mandatory			(DELETE,TYPE=STN-station / DISPLAY,TYPE=STN-station / REGENERATE,TYPE=STN-station)
	Possible Values:	numeric, up to 12 characters
TEAMNO	team number
	Type of Input:	single value, 1. parameter of a max-1-group			(ADD,TYPE=GR-group)
		single value, 5. parameter of a min-1-group			(CHANGE,TYPE=GR-group)
		single value, optional			(DISPLAY,TYPE=TEAM-pu group(s) with team number / REGENERATE,TYPE=TEAM-pu group(s) with team number)
	Possible Values:	numeric, 1-999
TYPE	desired call pickup group option
	Type of Input:	single value, mandatory			(ADD / CHANGE / DELETE)
	Type of Input:	single value, optional			(DISPLAY / REGENERATE)
	Possible Values:	GR	group
		NWRES	for networking reserved fictive pu group		(DELETE)
		ONS	One number service		(ADD / CHANGE / DISPLAY / REGENERATE)
		REM	remote link		(CHANGE / DELETE / DISPLAY / REGENERATE)
		STN	station		(DELETE / DISPLAY / REGENERATE)
		SYS	system		(DELETE / DISPLAY / REGENERATE)
		TEAM	pu group(s) with team number		(DISPLAY / REGENERATE)

Error Messages

F01	F01: NO DIGIT ANALYSIS RESULT FOUND FOR PU (PICK-UP).
F02	F02: GRNO INADMISSIBLE, SYSTEM OFFERS GROUPS 1 TO @@@@ PLEASE USE COMMAND 'ADD-DIMSU:TYPE=USER,PUGR=2000;' TO INCREASE MAXIMUM GROUP NUMBER.
F03	F03: ALL GROUPS ASSIGNED.
F04	F04: TOO MANY PU GROUP MEMBERS (STNO'S + REMOTE LINKS) SPECIFIED; MAXIMUM OF @@@ MEMBERS PER PU GROUP.
F05	F05: STNO @@@@@@@@@@@@ IS NOT A USER NO.
F06	F06: STNO @@@@@@@@@@@@ NOT PRESENT.
F07	F07: EXCEPTION OCCURED.
F08	F08: STNO @@@@@@@@@@@@ HAS ALREADY BEEN ENTERED IN GROUP @@@@.
F09	F09: MAXIMUM @@@ DIGITES ALLOWED; STNO @@@@@@@@@@@@ CANNOT BE ENTERED.
F10	F10: GROUP NOT ASSIGNED.
F11	F11: PU GROUP ALREADY HAS MAX. NUMBER OF USERS (STNO + REMOTE LINKS).
F12	F12: TOO MANY PU GROUP MEMBERS (STNO'S + REMOTE LINKS) SPECIFIED; ONLY @@@ USERS MAY BE ENTERED.
F13	F13: NEITHER PU GROUPS NOR ONS GROUPS NOT ASSIGNED IN SYSTEM.
F14	F14: STNO @@@@@@@@@@@@ NOT ENTERED IN GROUP.
F15	F15: TOO FEW GROUP MEMBERS (MINIMUM 1 STNO).
F16	F16: ALL VALUES OF STNO ERRONEOUS.
F17	F17: STNO @@@@@@@@@@@@ AND @@@@@@ ARE EXECUTIVE/SECRETARY NUMBERS OF AN INTEGRATED EXEC. TEL. SYSTEM AND MAY NOT BE ENTERED INTO THE SAME PU GROUP.
F18	F18: STNO @@@@@@@@@@@@ IS ENTERED IN EXEC. TEL. SYSTEM. EXECUTIVE/SECRETARY @@@@@@ OF THE SAME EXEC. TEL. SYSTEM ALREADY ENTERED IN PU GROUP.
F19	F19: RANGE LIMITS IN STNO PARAMETER HAVE DIFFERENT LENGTHS.
F21	F21: STNO @@@@@@@@@@@@ IS THE ANALOG SIDE OF A MODEM.
F23	F23: PARKED CALL OF PU GROUP @@@@ CANNOT BE CLEARED. RESTART AMO.
F24	F24: STNO @@@@@@@@@@@@ IS WITNESS STATION.
F27	F27: STNO @@@@@@@@@@@@ IS A MULTIPLE SUBSCRIBER NUMBER CONNECTED TO A BUS OR OPTISET CONFIGURATION NOT COMPRISING A FUNCTIONAL VOICE DEVICE (SET600)- SEE DISPLAY-SBCSU:STNO=@@@@@@@@@@@@,TYPE=BUS;
F28	F28: @@@@@@@@@@@@ IS A @@@@@ SPECIAL SUBSCRIBER WHICH IS NOT ALLOWED IN A CALL PICKUP GROUP AND ONS GROUP.
F29	F29: PARAMETERS REMAC, REMGRNO HAVE TO BE OMITTED OR SPECIFIED BOTH.
F30	F30: A REMOTE LINK TO THE SPECIFIED NODE (REMAC = @@@@@@@@@@@@@@@@@@@@@@) ALREADY EXISTS IN THE PICKUP GROUP.
F31	F31: THE OWN NODE ACCESS CODE (AMO ZAND, PARAMETER = PNODECD) IS NOT ALLOWED AS REMAC.
F32	F32: NO MEMORY AVAILABLE FOR REMOTE LINKS. PLEASE CORRECT WITH: ADD-DIMSU:REMPUGR=XXX.
F33	F33: REMOTE LINK SPECIFIED BY REMAC, IS NOT A MEMBER OF PU GROUP @@@@.
F34	F34: GRSTNO = @@@@@@@@@@@@ IS NOT MEMBER OF ANY GROUP.
F35	F35: THE PARAMETER STNO MUST NOT COMPRISE MORE THAN @@@ SUBSCRIBERS. @@@ SUBSCRIBERS ARE DELETED.
F36	F36: STNO @@@@@@@@@@@@ IS DESIGNATED AS TEAM MEMBER IN PICKUP GROUP @@@@. THIS GROUP IS ALREADY PART OF A NETWORK-WIDE TEAM (TEAM NUMBER @@@) AND IS THEREFORE NOT ALLOWED TO BE ENLARGED BY A TEAM MEMBER. THE PICKUP GROUP HAS TO BE DELETED AND CREATED AGAIN.
F37	F37: STNO @@@@@@@@@@@@ IS MEMBER OF PICKUP GROUP @@@@ WHICH IS PART OF A NETWORK-WIDE TEAM (TEAM NUMBER @@@). A TEAM MEMBER CANNOT BE MOVED OR DELETED FROM A NETWORK-WIDE TEAM. ONLY THE WHOLE PICKUP GROUP CAN BE REMOVED.
F38	F38: PICKUP GROUP @@@@ IS PART OF A NETWORK-WIDE TEAM (TEAM NUMBER @@@). THE TEAM MEMBERS (SEE FOLLOWING LIST) @@@@@@@@@@@@ @@@@@@@@@@@@ @@@@@@@@@@@@ @@@@@@@@@@@@ @@@@@@@@@@@@ @@@@@@@@@@@@ @@@@@@@@@@@@ @@@@@@@@@@@@ MUST BE HARD LOCKED BEFORE DELETING THE PICKUP GROUP ( DEAC-DSSU:OFFTYPE=DI,TYPE=STNO,STNO= ).
F40	F40: TEAMNO WAS NOT ASSIGNED TO PICKUP GROUP @@@@ BECAUSE NO SUITABLE DEVICE EXISTS.
F41	F41: THE NETWORKING RESERVED FICTIVE PICKUP GROUP @@@@ HAS NOT BEEN DELETED. THIS CAN BE DONE BY USING A SEPERATE DELETE BRANCH (TYPE=NWRES).
F42	F42: THE PICKUP GROUP @@@@ IS RESERVED FOR NETWORKING AND CANNOT BE MODIFIED (EXCEPTION: REMOTE LINKS CAN BE ADDED AND DELETED)
F43	F43: IN A FICTIVE, FOR NETWORKING RESERVED PU GROUP, ONLY ONE FLOATING STATION IS ALLOWED.
F44	F44: AN EXISTING PU GROUP MUST NOT BE CONVERTED INTO A FICTIVE, FOR NETWORKING RESERVED GROUP.
F45	F45: THE REMOTE LINK IS MEMBER OF PU GROUP @@@@. THIS GROUP IS RESERVED FOR NETWORKING AND MUST NOT BE MODIFIED.
F46	F46: STNO @@@@@@@@@@@@ IS MEMBER OF PU GROUP @@@@. THIS GROUP IS RESERVED FOR NETWORKING AND MUST NOT BE MODIFIED.
F47	F47: ONLY ONE PU GROUP WITH NETWORKING RESERVED ATTRIBUTE IS ALLOWED IN SYSTEM. PU GROUP @@@@ HAS ALREADY ATTRIBUTE NWRES.
F48	F48: NO PU GROUP WITH NETWORKING RESERVED ATTRIBUTE CONFIGURED IN SYSTEM.
F49	F49: STATION @@@@@@@@@@@@ MUST BE DEFINED AS A MASTER PHONE BY AMO-SDAT. (CHANGE-SDAT:STNO=@@@@@@@@@@@@,TYPE=ATTRIBUT,AATTR=PARARNGM)
F50	F50: ONS GROUP CAN HAVE ONLY ONE MASTER PHONE.
F51	F51: ONS GROUP MEMBERS MUST BE DEFINED AS MASTER OR SECONDARY BY AMO-SDAT.
F52	F52: A CHESE GROUP MEMBER CAN NOT BE ONS GROUP MEMBER AT THE SAME TIME.
F53	F53: THE ENTERED STATION NUMBER IS MEMBER OF A PICKUPGROUP AND CAN NOT BE MOVED TO AN ONS GROUP.
F54	F54: ONS GROUP MEMBERS CAN NOT BE ASSIGNED TO DIFFERENT ITR GROUPS.
F55	F55: THE ENTERED STATION NUMBER IS MEMBER OF AN ONS GROUP AND CAN NOT BE MOVED TO A PICKUPGROUP.
F56	F56: ONS GROUP MEMBERS MUST NOT BE NIGHT STATIONS.
F57	F57: MASTER OF A HUNTING GROUP CANNOT BE MEMBER OF ONS GROUP.
F58	F58: MEMBER OF A HUNTING GROUP CAN NOT BE SECONDARY PHONE OF AN ONS GROUP.
F59	F59: A KEYSET CAN NOT BE USED AS MASTER OR SECONDARY PHONE IN AN ONS GROUP.
F60	F60: THIS STATION NUMBER BELONGS TO MASTER PHONE OF AN ONS GROUP. IT CAN BE DELETED ONLY IF ALL SECONDARY DEVICES OF THE ONS GROUP WERE DELETED.
F61	F61: THERE MUST BE A MASTER PHONE FOR ONS GROUP.
F62	F62: REMAC IS ALREADY A MEMBER OF A PU GROUP.
F63	F63: REMAC IS ALREADY A MEMBER OF AN ONS GROUP.
F64	F64: ONS GROUP MEMBERS CAN NOT BE ASSIGNED TO DIFFERENT DPLN GROUPS.
F65	F65: ONS GROUP MEMBERS CAN NOT BE ASSIGNED TO DIFFERENT COSX GROUPS.
F66	F66: ONS GROUP ALREADY HAS MAXIMUM NUMBER OF USERS (STNO).
F67	F67: ONS GROUP CAN HAVE ONLY ONE REMAC.
F68	F68: GRNO=@@@@ IS NOT AN ONS GROUP, IT IS A PU GROUP.
F69	F69: GRNO=@@@@ IS NOT A PU GROUP, IT IS AN ONS GROUP.
F70	F70: GRSTNO=@@@@@@@@@@@@ IS NOT MEMBER OF ANY ONS GROUP. IT IS A MEMBER OF A PICKUP GROUP WITH GROUP NUMBER @@@@.
F71	F71: GRSTNO=@@@@@@@@@@@@ IS NOT MEMBER OF ANY PICKUP GROUP. IT IS A MEMBER OF AN ONS GROUP WITH GROUP NUMBER @@@@.
F72	F72: GRNO=@@@@ IS NOT A PU GROUP, IT IS AN ONS GROUP. IN ORDER TO CHANGE REMAC OF ONS GROUP PLEASE USE COMMAND: CHANGE-AUN:TYPE=ONS,GRNO=@@@@,REMAC=...
F73	F73: GRNO=@@@@ IS NOT AN ONS GROUP, IT IS A PU GROUP. PLEASE FIRST DELETE THE PU GROUP, THEN RECONFIGURE IT AS AN ONS GROUP.
F74	F74: GRNO=@@@@ IS NOT A PU GROUP, IT IS AN ONS GROUP. PLEASE FIRST DELETE THE ONS GROUP, THEN RECONFIGURE IT AS A PU GROUP.
F75	F75: NO REMAC IS ASSIGNED FOR ONS GROUP @@@@.
F76	F76: STNO @@@@@@@@@@@@ CANNOT BE ADDED TO ONS GROUP @@@@, SINCE STNO IS A SECRETARY DEVICE.
F77	F77: REMAC CANNOT BE ASSIGNED TO ONS GROUP @@@@, SINCE THERE IS NO VIRTUAL ONS SECONDARY MEMBER. PLEASE CREATE A VIRTUAL MEMBER WITH AMO-SCSU (DVCFIG=AUXDIGI AND INS=ACLSTN).
F78	F78: VIRTUAL STATION @@@@@@@@@@@@ CANNOT BE DELETED WHILE REMAC STILL EXISTS. FIRST DELETE REMAC, THEN DELETE VIRTUAL STATION @@@@@@@@@@@@
F79	F79: ONS GROUP MEMBERS MUST NOT BE FUNCTIONAL DEVICES.
F80	F80: ONLY THREE REAL MEMBER AND ONE VIRTUAL MEMBER CAN BE ADDED TO AN ONS GROUP.
F82	F82: COSHOME PARAMETER OF ONS PIN MUST SET TO YES WITH AMO PERSI. (CHA-PERSI:TYPE=COPIN,COPIN=@@,COSHOME=YES;)
F83	F83: THE PARARNGM PARAMETER FOR AT LEAST ONE OF THE COPIN NUMBERS OF STN(@@@@@@@@@@@@) MUST BE SET TO 'YES'.
F84	F84: ALL MEMBERS OF AN ONS GROUP MUST BE IN THE SAME VIRTUAL NODE.
F85	F85: ONLY REAL DEVICES CAN BE ONS MASTERS, IT IS NOT ALLOWED TO ADD A VIRTUAL DEVICE AS ONS MASTER.
F86	F86: IF THE MASTER OF AN ONS GROUP IS SIP, IT IS NOT ALLOWED TO ADD MORE THAN TWO SLAVES. THESE SLAVES MUST BE SIP SUBSCRIBERS.
F87	F87: IF THE MASTER OF AN ONS GROUP IS SIP, IT IS NOT ALLOWED TO ADD REMAC TO THE GROUP.
F88	F88: SIP STATION ADDED FROM REMAC CAN ONLY BE DELETED FROM REMAC. DEL-AUN:TYPE=REM,GRNO=@@@@,REMAC=@@@@@@@@@@@@;
F90	F90: IF THE MASTER OF AN ONS GROUP IS NOT SIP, ITS SLAVES CANNOT BE SIP SUBSCRIBERS.
F91	F91: THE MASTER HAS AN ACTIVATED CALL FORWARD TO SLAVE.
F92	F92: STATION @@@@@@@@@@@@ IS A DESK/CLIENT OR AN ASSOCIATED DEVICE AND CANNOT BE MEMBER IN A ONS GROUP. (DISP-SDAT:@@@@@@@@@@@@;)
F93	F93: STATION @@@@@@@@@@@@ IS A CIRCUIT CLIENT PHONE, CANNOT BE MEMBER IN A PU GROUP.

Advisory Messages

H01	H01: PU GROUP @@@@ EXTENDED BY: NUMBER OF STNO'S: @@@, NUMBER OF REMOTE LINKS: @@@
H02	H02: GROUP WITH GRNO @@@@ DELETED
H03	H03: PU GROUP @@@@ CREATED WITH: NUMBER OF STNO'S: @@@, NUMBER OF REMOTE LINKS: @@@
H04	H04: NEITHER PU GROUPS NOR ONS GROUPS ASSIGNED IN SYSTEM
H05	H05: NO MEMORY AVAILABLE FOR PARKING CONFIGURATION (SYSTEM CONSTANT, NO DIMSU PARAMETER)
H06	H06: VALUES OF STNO ERRONEOUS OR NOT ENTERED IN PU GROUP
H07	H07: PU GROUPS NOT ASSIGNED
H09	H09: NO MEMORY AVAILABLE FOR PARKING CONFIGURATION - REMEDY: RESERVE MORE MEMORY BY - ADD-DIMSU:STN=XXXX;
H10	H10: NO MEMORY AVAILABLE FOR PARKING CONFIGURATION - REMEDY: RESERVE MORE MEMORY BY - ADD-DIMSU:LODEN=XXXX;
H11	H11: THE PARAMETERS REMSIGO, REMSIGI AND REMSIGPK ARE IGNORED IF NO REMOTE LINK IS SPECIFIED
H12	H12: THE REMOTE LINK HAS BEEN ENTERED IN PU GROUP @@@@. PLEASE ENTER COMMAND AT REMOTE NODE (AMO ZAND, PNODECD=@@@@@@@@@@@@@@@@@@@@@@): ADD-AUN:GRNO=@@@@,REMAC=@@@@@@@@@@@@@@@@@@@@@@,REMGRNO=@@@@;
H13	H13: THE PICKUP GROUP @@@@ WORKS WITH SIGNALING MODE @@@@@ (@@@@@@@@@@@@@@@@@@@DEFAULT VALUE)
H14	H14: REMOTE LINK, SPECIFIED BY REMAC, IS NOT A MEMBER OF ANY PU GROUP
H15	H15: NO REMOTE LINK PRESENT IN ANY PU GROUP
H16	H16: A REMOTE LINK HAS BEEN DELETED FROM PU GROUP @@@@. PLEASE DELETE AT REMOTE NODE (AMO ZAND, PNODECD=@@@@@@@@@@@@@@@@@@@@@@) ALSO THE CORRESPONDING LINK BY: DEL-AUN:TYPE=REM,GRNO=@@@@,REMAC=@@@@@@@@@@@@@@@@@@@@@@;
H17	H17: PU GROUP WITH GRNO @@@@ CONTAINS ONLY 1 STATION
H18	H18: STNO @@@@@@@@@@@@ MOVED FROM PU GROUP @@@@ TO PU GROUP @@@@
H19	H19: REMOTE LINK (REMAC = @@@@@@@@@@@@@@@@@@@@@@, REMGRNO = @@@@) MOVED FROM PU GROUP @@@@ TO PU GROUP @@@@
H20	H20: STNO @@@@@@@@@@@@ DELETED FROM GROUP @@@@
H22	H22: TEAMNO WAS NOT ASSIGNED TO PICKUP GROUP @@@@ BECAUSE NO SUITABLE DEVICE EXISTS.
H24	H24: THE SPECIFIED TEAM NUMBER (TEAMNO) IS NOT A MEMBER OF ANY PU GROUP.
H25	H25: NO TEAM IS PRESENT IN ANY PU GROUP
H26	H26: THE NETWORKING RESERVED FICTIVE PICKUP GROUP @@@@ HAS NOT BEEN DELETED. THIS CAN BE DONE BY USING A SEPERATE DELETE BRANCH (TYPE=NWRES).
H28	H28: THE NETWORKING RESERVED PU GROUP @@@@ HAS BEEN DELETED
H29	H29: SMPF ATTRIBUTE OF ONS GROUP @@@@ IS ASSIGNED TO 'YES' SINCE REMAC IS ADDED.
H30	H30: FOR THE ONS GROUP IT IS NECESSARY TO ASSIGN A PERMANENT PIN WITH PINDUR=PERM AND PARARNGM=YES FOR THE ONS MASTER.
H31	H31: SMPF ATTRIBUTE OF ONS GROUP @@@@ IS ASSIGNED TO 'NO' SINCE REMAC IS REMOVED.
H32	H32: SMPF ATTRIBUTE OF ONS GROUP @@@@ IS ASSIGNED TO 'NO' SINCE NO REMAC ASSIGNED.
H34	H34: ONS GROUP @@@@ EXTENDED BY: NUMBER OF STNO'S: @@@, NUMBER OF REMAC: @@@
H35	H35: ONS GROUP @@@@ CREATED WITH: NUMBER OF STNO'S: @@@, NUMBER OF REMAC: @@@
H36	H36: ONS GROUP WITH GRNO @@@@ CONTAINS ONLY 1 STATION
H37	H37: STNO @@@@@@@@@@@@ MOVED FROM ONS GROUP @@@@ TO ONS GROUP @@@@
H38	H38: IT IS NOT ALLOWED TO ADD A STATION AS REMAC UNLESS IT IS SIP. WITH PARARNGS
H39	H39: THE SLAVE HAS AN ACTIVATED CALL FORWARDING TO MASTER. THE CALL FORWARDING WILL BE DELETED.