166.4.2 Advisories


H01:	WHEN ENTERING STATION NUMBER RANGES, THE NUMBER OF DIGITS FOR EACH LIMIT MUST BE EQUAL. THE STNO RANGE <xxxxxxxxxxxx>-<yyyyyyyyyyyy> CANNOT BE PROCESSED
H02:	<xxxxxxxxxxxx> AUTOMATIC SEARCH FOR THE NEXT AVAILABLE PEN WILL BE RESTRICTED TO THOSE LTU SHELVES HAVING SOURCE GROUP 1 ASSIGNED ( DISP-UCSU:UNIT=SRCGRP,SRCGRP=1; )
H03:	<xxxxxxxxxxxx> THIS STATION IS ASSIGNED IN THE EXECUTIVE TELEPHONE SYSTEM <nnnn>. PLEASE CHECK THE TRAFFIC RESTRICTIONS ITR OF THE EXECUTIVE SYSTEM
H04:	<xxxxxxxxxxxx> THIS STATION IS ASSIGNED
H05:	<xxxxxxxxxxxx>THIS STATION IS ASSIGNED AT PEN <g-uu-sss-ccc>
H06:	<xxxxxxxxxxxx> STATION DATA DELETED
H07:	<xxxxxxxxxxxx> STATION DATA CHANGED
H08:	<xxxxxxxxxxxx> STATION RELEASED FOR CALL PROCESSING
H09:	<xxxxxxxxxxxx> THE STATION IS NOT ACTIVATED <(SIGNED OFF STATION)>
H10:	<xxxxxxxxxxxx> DOWNLOAD OF <ASYNCT/EXTBUS/IPPASSW/LWPAR/NEWNO/PERMACT/PATTERN/ VCI/VPI> CHANGE TO THE MODULE WILL BE INITIATED AFTER DEACTIVATION AND RE-ACTIVATION OF THE CIRCUIT ( RESTART-DSSU:TYPE=PEN,PEN1=<g-uu-sss-ccc>; )
H11:	<xxxxxxxxxxxx> NO STATION HAS BEEN ASSIGNED
H12:	****** PLEASE NOTE : ********************************************* <xxxxxxxxxxxx> <PACKAGE ’FLEX LICENSE’ / PACKAGE ’CORDLESS E’ > EXCEEDED : <OPTISET/OPTIP500/OPTIIP/.../ANADTE> IS MARKED AS TRIAL ENTITY. MARKED DEVICES WILL BE BLOCKED, IF TRIAL MODE EXPIRES WITHOUT SUFFICIENT LICENSES (APPROX. @@@@@ DAYS LEFT). *********************************************************************
H12:	****** PLEASE NOTE : ********************************************* <xxxxxxxxxxxx> <PACKAGE ’FLEX LICENSE’ / PACKAGE ’CORDLESS E’ > EXCEEDED : <OPTISET/OPTIP500/OPTIIP/.../ANADTE> IS BLOCKED BECAUSE TRIAL MODE HAS EXPIRED WITHOUT SUFFICIENT LICENSES *********************************************************************
H13:	<xxxxxxxxxxxx> <STMI-HFA/STMI2-HFA> MODULE IN LTU <uu>, SLOT <sss> WILL BE IGNORED, BECAUSE THE <STMIHFA1/STMIHFA2> BOARD CONFIGURATION DATA HAS NOT YET BEEN SET UP ( ADD-HFAB:MTYPE=<STMIHFA1/STMIHFA2>,LTU=<uu>,SLOT=<sss>, <SMODE=NORMAL,> IPADDR=??, <NETMASK=??,> )
H14:	<xxxxxxxxxxxx> PARAMETER <param> DOES NOT MATCH TERMINAL <dvcfig> AND WILL THEREFORE BE IGNORED <param> :APICLASS\|APMOBUSR\|BASICSVC\|CALLOG\|CBKBMAX\|DCFWBUSY\|DFSVCANA\| DIGNODIS\|DNIDSP\|DOPTIDX\|DPROT\|DSSTNA\|DSSTNB\|DTMFBLK\|DTMFCTRD\| EXTBUS\|FLASH\|FOPTIDX\|FPROT\|HEADSET\|HMUSIC\|HSKEY\|IPCODEC\| IPPASSW\|LWPAR\|OPTIDX\|PATTERN\|PMIDX\|RCBKB\|RCBKNA\|REP\|SECAPPL\| SOPTIDX\|SPROT\|STD\|TEXTSEL\|VCI\|VPI
H15:	THE STNO <xxxxxxxxxxxx> HAS THE NEW NUMBER <yyyyyyyyyyyy>
H16:	A RANGE INPUT FOR THE PARAMETER STNO MUST NOT COMPRISE MORE THAN 600 STATIONS. THE RANGE HAS BEEN TRUNCATED TO <xxxxxxxxxxxx>-<yyyyyyyyyyyy> FOR PROCESSING
H17:	<xxxxxxxxxxxx> SPECIFIED STATION(S) NOT ASSIGNED BY AMO SBCSU
H18:	<xxxxxxxxxxxx> NO STATION ASSIGNED BY AMO SBCSU IN THE PABX
H19:	@@@@@@@@@@@@ THE ADDITIONAL ADDED FUNCTIONAL TERMINALS ARE NOT ACTIVATED. DEACTIVATE AND REACTIVATE THE STATION WITH AMO DSSU
H20:	<xxxxxxxxxxxx> STMI2-HFA MODULE IN LTU <uu>, SLOT <sss> WILL BE IGNORED, BECAUSE IT IS CURRENTLY DEFINED AS A STANDBY BOARD, WHICH CANNOT BE USED FOR SUBSCRIBER CONFIGURATION ( DISP-HFAB:MTYPE=STMIHFA2,LTU=<uu>,SLOT=<sss>; ) THE PARAMETERS OF THE VOICE TERMINAL WILL BE USED
H21:	<xxxxxxxxxxxx> PARAMETER OPT IS NOT REQUIRED AND WILL THEREFORE BE IGNORED.
H22:	<xxxxxxxxxxxx> MSN STATION NUMBER HAS BEEN ASSIGNED FOR <THE SERVICE/THE SERVICES> <VOICE/FAX/DTE>.
H23:	<xxxxxxxxxxxx> MSN STATION NUMBER HAS BEEN DELETED FOR <THE SERVICE/THE SERVICES> <VOICE/FAX/DTE>.
H24:	<xxxxxxxxxxxx> MSN STATION NUMBER HAS BEEN EXTENDED BY <THE SERVICE/THE SERVICES> <VOICE/FAX/DTE>.
H25:	<xxxxxxxxxxxx> MSN STATION NUMBER HAS BEEN SHORTENED BY <THE SERVICE/THE SERVICES> <VOICE/FAX/DTE>.
H26:	<xxxxxxxxxxxx> MSN STATION NUMBER HAS BEEN DELETED, SINCE THERE ARE NO FUNCTIONAL SERVICES LEFT AT THE CONFIGURATION WITH MAINO <yyyyyyyyyyyy>.
H27:	<xxxxxxxxxxxx> ALL MSN STATION NUMBERS FOR STNO <yyyyyyyyyyyy> HAVE BEEN DELETED, SINCE THERE ARE NO FUNCTIONAL SERVICES LEFT.
H28:	<xxxxxxxxxxxx> PARAMETER TSI IS NOT ALLOWED FOR MSN STATION NUMBERS (ONLY FOR MSN SECONDARY STATION NUMBERS) AND WILL BE IGNORED.
H29:	****** PLEASE NOTE : ********************************************* <xxxxxx> FOR THE IP DEVICE THE <NEW> STNO <yyyyyyyyyyyy> MUST ALSO BE SET ! *********************************************************************
H31:	<xxxxxxxxxxxx> PARAMETER <param> CAN ONLY BE CHANGED FOR THE MAIN STATION <yyyyyyyyyyyy> AND WILL THEREFORE BE IGNORED. <param> :ALARMNO\|DOPTIDX\|DPLN\|DPROT\|FOPTIDX\|FPROT\|OPTIDX\|PROT\| SOPTIDX\|SPROT
H32:	<xxxxxxxxxxxx> PARAMETER <param> CANNOT BE SPECIFIED WITH MSN NUMBERS AND WILL THEREFORE BE IGNORED. <param> :DIGNODIS\|DSSTNA\|DSSTNB\|EXTBUS\|IDCR\|PERMACT\|REP\|SECR
H33:	<xxxxxxxxxxxx> PARAMETER <param> WAS ADAPTED AUTOMATICALLY FOR ALL ASSOCIATED MSN NUMBERS. A LIST OF ALL AFFECTED MSN NUMBERS CAN BE FOUND USING: DISP-SBCSU:STNO=<yyyyyyyyyyyy>,TYPE=<BUS/FPP>; <param> :ALARMNO\|BASICSVC\|DPLN\|OPT\|PROT
H35:	<xxxxxxxxxxxx> THE TERMINAL ADAPTER <OPTISPA/OPTIS0A> FOR CONNECTING <THIS OPTISET/THIS OPTIP500/S0 DEVICES> MUST BE PLUGGED AT MAIN STATION NUMBER <yyyyyyyyyyyy> .
H36:	<xxxxxxxxxxxx> THE TERMINAL ADAPTER <OPTISPA/OPTIS0A/OPTIABA> PLUGGED AT MAIN STATION NUMBER <yyyyyyyyyyyy> FOR CONNECTING <THIS OPTISET/THIS OPTIP500/S0 DEVICES/ ANALOG DEVICES> IS NO LONGER NEEDED.
H37:	<xxxxxxxxxxxx> PARAMETER <ASYNCT/IPPASSW/PATTERN/VCI/VPI> DOES NOT MATCH MODULE <mmmmmmmmmmmmmmmmmmmm> OF THE CORRESPONDING PEN AND WILL THEREFORE BE IGNORED.
H38:	<xxxxxxxxxxxx> PARAMETER <ASYNCT/EXTBUS/PATTERN/PEN/TSI/VCI/VPI> WILL BE IGNORED FOR <CONN=<ATMPSW/DIR/PNT> / INS=SIGNOFF>
H39:	<xxxxxxxxxxxx> FOR TYPE=SVC THE PREVIOUS VALUE OPTIDA=<old_value> MAY NOT BE EXCEEDED. A LOWER VALUE CAN ONLY BE SET BY USING THE COMMAND CHANGE-SBCSU:STNO=<xxxxxxxxxxxx>,OPT=OPTI,OPTIDA=<new_value>;
H39:	<xxxxxxxxxxxx> FOR TYPE=SVC THE PREVIOUS VALUE <BASICSVC/OPTIDA/OPTIDA>=<old_value> MAY NOT BE ALTERED. A NEW VALUE CAN ONLY BE SET BY USING THE COMMAND CHANGE-SBCSU:STNO=<xxxxxxxxxxxx>,OPT=<FBUS/OPTI>, <BASICSVC/OPTIDA/OPTIDA>=<new_value>;
H40:	<xxxxxxxxxxxx> FOR OPTICOM=Y, REP=2 IS SET
H41:	<xxxxxxxxxxxx> PARAMETER REP IS IGNORED BECAUSE OPTICOM=Y IS ALREADY SET
H42:	<xxxxxxxxxxxx> ALL SIGNED OFF TSIS AT PEN <g-uu-sss-ccc> HAVE BEEN RELEASED
H43:	%%%%%%%% PLEASE NOTE : %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% <xxxxxx> THE STATION IS IN AN UNDEFINED SIGN OFF STATE. PLEASE SIGN OFF USING CHANGE-DSSU:TYPE=SIGNOFF,STNO=<xxxxxx>; %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
H44:	<xxxxxxxxxxxx> DEACTIVATION OR DOWNLOADING IS NOT REQUIRED - PARAMETER OFFTYPE WILL BE IGNORED.
H45:	<xxxxxxxxxxxx> DEFAULT VALUE SLKTYPE=SLKSTNO HAS BEEN SET FOR EVERY NEW PUS RESP. RNGXFER KEY AND CAN BE MODIFIED VIA CHANGE-CHESE:GRNO=@@@@@,TYPE=EXECSLK,SLKTYPE=??, ...; RESP. CHANGE-CHESE:GRNO=@@@@@,TYPE=SECRSLK,SLKTYPE=??, ...;
H47:	<xxxxxxxxxxxx> THE PARAMETER TEXTSEL IS IGNORED BECAUSE THE MODULE DOES NOT SUPPORT THE MULTI-LINGUAL FUNCTION
H48:	<xxxxxxxxxxxx> THE PARAMETER TEXTSEL IS NOT EFFECTIVE BECAUSE THIS LANGUAGE HAS NOT BEEN SET UP IN THE CENTRAL SYSTEM DATA (AMO ZAND, PARAMETER TEXTSEL)
H50:	<xxxxxxxxxxxx> ... STILL WAITING FOR A CONFIRMATION BY CALL PROCESSING (MAXIMUM 120 SEC)
H51:	****** PLEASE NOTE : ********************************************* <xxxxxxxxxxxx> FOR DVCFIG = <OPTISET/OPTIP500>< DUE TO IDCR=Y > ONLY A MAXIMUM OF REP = <3/1> IS POSSIBLE. ALL OTHER ADD-ON UNITS CANNOT BE OPERATED. *********************************************************************
H52:	****** PLEASE NOTE : ********************************************* <xxxxxxxxxxxx> FOR DVCFIG=<OPTISET/OPTIP500/OPTIIP> ONLY 2 TERMINAL ADAPTERS CAN BE PLUGGED AT ONE TIME. *********************************************************************
H53:	<xxxxxxxxxxxx> DOWNLOAD OF <ASYNCT/EXTBUS/IPPASSW/LWPAR/NEWNO/PATTERN/PERMACT/ VCI/VPI> CHANGE TO THE MODULE FOR PEN <g-uu-sss-ccc> HAS BEEN INITIATED
H54:	<xxxxxxxxxxxx> POSITIVE RESPONSE FROM DIAG-SWU: THE ENTRY IN CORDLESS PHONEBOOK HAS BEEN SUCCESSFULLY ^vartxt01^.
H55:	<xxxxxxxxxxxx> NEGATIVE RESPONSE FROM DIAG-SWU: THE ENTRY IN CORDLESS PHONEBOOK COULD NOT BE ^vartxt01^.
H56:	<xxxxxxxxxxxx> UPDATE MESSAGE TO PHONEBOOK APPLCATION (PBP_APP) WAS NOT SENT (APPLICATION IS NOT CONFIGURED)
H59:	<xxxxxxxxxxxx> THE SUBSCRIBER BELONGS TO VIRTUAL NODE <xxxxxxxxxx>
H60:	<xxxxxxxxxxxx> DPLN <xxx> WILL BE COPIED FROM MODE <xxxxxxxxxx>.
H61:	IF PASSWD OR USERID IS SPECIFIED, SECZONE SHOULD BE SPECIFIED TOO.
H62:	FOR SIP SUBSCRIBERS PARAMETER MBCHL (MULTIPLE BCHANNEL) MUST BE SET IN AMO-SDAT.
H63:	THIS DATA CHANGE WILL BE INITIATED AFTER DEACTIVATION AND RE-ACTIVATION OF THE CIRCUIT. (RESTART-DSSU:TYPE=PEN,PEN1=<xx>-<xx>-<xxx>-<xxx>;)
H64:	THE EXISTING DPLN OF THE STATION IS NOT IN ADPLN OF THE NEW NODE, SO IT IS INTERNALLY SET TO THE DPLN OF THE NEW NODE.
H65:	<xxxxxxxxxxxx> PARAMETER TEXTSEL IS NOT EFFECTIVE BECAUSE THIS LANGUAGE HAS NOT BEEN SET UP IN AP SPECIFIC DATA (AMO UCSU,PARAMETER TEXTSEL)
H66:	The special character 'space' in IPPASSW field was ignored.
H67:	@@@@@@@@@@@@ PARAMETER @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@ CAN ONLY BE SET FOR AN UFIP CLIENT DEVICE, THEREFORE WILL BE IGNORED.
H68:	WARNING: not all parameters for UFIP IPPASW, USER ID & SECZONE have entries. UFIP requires entries for each parameter to allow digest registration.
H99:	<xxxxxxxxxxxx> <xxxxxxxx>=<xxxxxxxx> IS NOT SUPPORTED <xxxxxxxxxxxxxxx>

OpenScape 4000 V10, Volume 1: AMO Descriptions, Service Documentation, Issue 5, ID: P31003H31A0S107057620

© 09/2025 Mitel Networks Corporation. - All rights reserved.
Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG. All other trademarks herein are the property of their respective owners.