166.1 Interrelationships

 
•
AMO ACDRT
:
ACD Routing Tables
•
AMO AUN
:
Call Pickup Group
•
AMO BCSU
:
Board Configuration, Switching Unit
The AMO BCSU configures the following modules:
DIU-N2, DIU-N4, DIU-S2, SLC24, SLMO, SLOP2, SLMQ, SLMQ3, SLMS, STHC, STHC2, STMA, STMD, STMD2, STMI-HFA, STMI2-HFA and WAML2
•
AMO BDAT
:
Configuration of STMA Module Data
•
AMO BERUM
:
Class of Service Switchover
•
AMO CHESE
:
Executive/Secretary Arrangements
•
AMO CODEW
:
Administration of System Code word
•
AMO COMGR
:
Communications Group Calling
•
AMO COSSU
:
Class-of-Service, Switching Unit
The AMO COSSU creates classes-of-service, which can be assigned to a station line circuit with the parameters COS1 and COS2.
The same AMO can be used to create the LCR classes-of-service (for services VOICE and DTE), which can be assigned to a subscriber line with parameters LCOSV1 and LCOSV2 or LCOSD1 and LCOSD2.
•
AMO DIMSU
:
Dimensioning of Features, Switching Unit
The AMO DIMSU administers the database layout for device memories and additional memories required by the call processing system and the device handler.
•
AMO SLCB
:
Configuration of CMI from Version V3.0 onward
•
AMO DNIT
:
Directory Number Information and Translation
•
AMO DSSU
:
Device Switch of Switching Unit
The AMO DSSU can be used to put an S0 bus and its terminals into service or to block it.
•
AMO FEASU
:
Customer Feature List
•
AMO HFAB
:
Configuration of STMI-HFA and STMI2-HFA board data
•
AMO KCSU
:
Keysystem configuration in Switching Unit
•
AMO LRNGZ
:
Central Speed Calling Dialing Lists
•
AMO LWPAR
:
Loadware Parameters for Networking Modules
•
AMO NAVAR
:
Administration of Static Night Switch Option Data
•
AMO PERSI
:
Personal Identification Data
•
AMO PRODE
:
Protocol Descriptor for Networking
•
AMO RCSU
:
Recorder Configuration in SWU
•
AMO SA
:
Hunting Arrangements
•
AMO SCSU
:
Station Configuration of Switching Unit
The AMO SCSU is used to assign virtual stations for associated terminal adapters
•
AMO SDAT
:
Administration of Subscriber Attributes and Data
•
AMO SSCSU
:
Special Subscriber Configuration of Switching Unit
AMO SSCSU configures the terminals additionally required for the remote user
•
AMO STMIB
:
Configuration of STMI2-IGW board data
•
AMO TAPRO
:
Key Programming for OPTISET / OPTIP500 / OPTIIP
•
AMO TGER
:
Station/Device Allocation, Incoming
•
AMO UCSU
:
Unit configuration of Switching unit
•
AMO VADSU
:
Administering NMC alarms in the SWU
•
AMO VBZ
:
Internal Traffic Restrictions
•
AMO WABE
:
Dialing Plans, Feature Access Codes
•
AMO ZAND
:
System Data
The AMO ZAND is used to define terminal pre-settings valid for new OPTISET / OPTIP500 / OPTIIP terminal devices to be configured.
The AMO ZAND also loads the option table(s) relevant to the functional terminal devices from Hard Disk and allows their subsequent modification.
•
AMO ZANDE
:
System Data
AMO ZANDE is used to configure the used CMI version.
•
AMO ZIEL
:
Destination addresses for subscribers
•
AMO ZIELN
:
Administrate Destinations for Network-wide Teams
•
AMO ZRNGZ
:
Central Speed Calling Digit Series
${DocTitle}, ID: ${DocID}
 © 02/2025 Mitel Networks Corporation. -  All rights reserved.
 Mitel and the Mitel logo are trademarks of Mitel Networks Corporation. Unify and associated marks are trademarks of Unify Software and Solutions GmbH&Co. KG.
 All other trademarks herein are the property of their respective owners.