SXSU - station exchanging (moves), switching unit

With AMO SXSU, only the action CHANGE is implemented. This action allows the following three functions to be performed:

Replacing a voice terminal
Changing the PEN of a voice terminal
Interchanging the station numbers of two voice terminals

a) Replacing a voice terminal

The AMO SXSU allows one voice terminal to be replaced by another in one node, without breaking up existing group memberships. The following source device types are supported:

ANATE
ANATE & NV

The destination device type can be an also an OPTISET device additional to the above listed device types. The following table figures out, which source device can be replaced by a certain destination device:

	ANATE	ANATE&NV	OPTISET
ANATE		X	X
ANATE&NV	X		X

Following device types will not be supported:

virtual subscribers (card subscriber and signed off subscriber),
SET600,
OPTISET/optiPoint as ATM subscriber and as remote Subscriber,
OPTISET/optiPoint with keysystem functionality,
CMI devices,
stations which are assigned with AMO SSCSU,
optiPoint 500,
users which are configured with connection type IP (AMO SBCSU, parameter CONN=IP2),
users which are configured with connection type SIP (AMO SBCSU, parameter CONN=SIP).

For combination of ANATE&NV only the non-voice devices FAX and DTEANA are valid. If the new terminal is an OPTISET, direct voice call protection is activated automatically

A terminal that is member of certain group or has particular features can only be replaced by a new device type if the group membership/features are also valid for the new terminal.

The possible combinations of device type (voice terminals only) and group membership/features are listed in the following table:

EG-Typ Group/feature	ANATE	ANATE&NV	OPTISET
PU-Group	X	X	X
Hunting Group Voice	X	X	X
Hunting Group Non Voice		X
Night option	X	X	X
fixed Forward Voice
fixed Forward Non Voice
Associiated Staion	X	X	X
Analog side of Modem	X
CLC-number	X
Witness attached with VBZGR	X
Exec./secr. system			X
Mailbox key			X
Voice calling			X

The combination ANATE&DTEA cannot be an associated station.

Additionally the following restrictions are valid:

An associated ANATE cannot be processed.
Any ANATE that is used as the analog side of a modem or as a listener cannot be replaced by a DIGITE.
ANATE&NV cannot be replaced if the NV terminal is a member (or the MASTER) of a NV hunting group, or has been assigned to other stations by means of AMO TGER.
A device cannot be substituted if it is a member of an active night option
Existing timed reminders are not adopted for the new terminal.
Existing LINs and SRCGRP are not adopted for the new terminal (see AMO SDAT).

All replacements that are not covered by AMO SXSU must be carried out using the actions DELETE and ADD (AMO SCSU/SBCSU/SSCSU).

The parameter PEN is used to designate the new PEN of the voice terminal.

The parameters STD, HFREE, SECR, DIGNODIS, COS1, COS2, LCOSV1 and LCOSV2 are used to specify the details of the new terminal's configuration. For all parameters that are not specified the original value of the parameter is retained providing it is acceptable for the new terminal configuration. Otherwise, the default value is used, which is defined in AMOs SCSU or SBCSU.

The parameter INS determines whether the new terminal is to be activated. If the parameter has not been specified, the original status of the station is retained.

b) Changing the PEN of a voice terminal

The physical port equipment number of any assigned voice terminal or multiple device connection (Optiset, Optipoint, OptiIP and UFIP) can be changed using this function.

The whole multiple device connection will be moved to the new physical port equipment number. Especially it is not possible, to move only a single device of a multiple device connection to another port.
Virtual subscribers and stations which have been assigned with AMO SSCSU cannot be processed.
Users which are configured with connection type SIP (AMO SBCSU, parameter CONN=SIP) cannot be processed.
After a successful PEN change, the MDF strapping or board IP address must be changed accordingly.
Existing LINs and SRCGRP are not adopted (see AMO SDAT).

c) Interchanging the station numbers of two voice terminals

The station numbers of two assigned voice terminals can be exchanged with one another.

Plese note: only the station number of the voice terminal, resp. voice terminals will be changed, all other data will be kept unchanged and remain assigned to the voice terminal.

Exception: at all DSS-partners the DSS-destination will be deleted if it leads to a voice terminal whose station number should be changed.

This function can also be used to change the first station number as long as no terminal has been assigned to the second station number STNOX (advance provision has been made for this). Possible call forwardings and DID number conversions are device- specific and remain assigned to the device after the station number has been changed.

The following users cannot be assigned a new station number (parameter NEWNO):

Users who have already been entered as a Route-to-Extension destination in an ACD Routing Table (AMO ACDRT).
Users for whom ACD attributes (AGENT, AUTOLOG, SUPER, CAF) have already been set with AMO SDAT.
Users for whom networkwide team attributes (TEAMEXEC, TEAMSECR) have already been set with AMO SDAT.
Users which are configured with connection type IP (AMO SBCSU, parameter CONN=IP2)
Users which are configured with connection type SIP (AMO SBCSU, parameter CONN=SIP)

Cross Reference to Other AMOs:

AMO BCSU	:	Board configuration, switching unit
AMO DCIC	:	DCI configuration
AMO DIMSU	:	Dimensioning of features, switching unit
AMO RUFUM	:	DID number conversion
AMO SA	:	Hunting arrangements
AMO SBCSU	:	Station configuration of switching unit
AMO SCSU	:	Subscriber configuration of switching unit
AMO SDAT	:	Subscriber data
AMO TAPRO	:	Programable key definition for digital terminals
AMO UCSU	:	Unit configuration of switching unit
AMO VBZGR	:	Internal Traffic Restriction Groups
AMO WABE	:	Digit analysis
AMO ZIEL	:	Destinations for various station features

Destination Processor: BP (Switching Unit)

Functions

DIALOG01	(internal)password class 5
CHANGE	password class 2

Procedure Overview

DIALOG01-SXSU

DIALOG01-SXSU

BGNAMEN=<param>;

CHANGE-SXSU

CHANGE-SXSU

STNO=<number>,

TYPE=DEV,

OPT=SCSU,DVCFIG=<param>, PEN=<number>, [COS1=<number>], [COS2=<number>], [LCOSV1=<number>], [LCOSV2=<number>], [STD=<number>], [SECR=<param>], [HFREE=<param>], [DIGNODIS=<param>], [INS=<param>];

OPT=OPTI,CONN=<param>, [DVCFIG=<param>], PEN=<number>, [COS1=<number>], [COS2=<number>], [LCOSV1=<number>], [LCOSV2=<number>], [STD=<number>], [SECR=<param>], [HFREE=<param>], [DIGNODIS=<param>], [INS=<param>];

OPT=OPTIEXP,[DVCFIG=<param>], MAINO=<number>, [COS1=<number>], [COS2=<number>], [LCOSV1=<number>], [LCOSV2=<number>], [STD=<number>], [SECR=<param>], [HFREE=<param>], [DIGNODIS=<param>], [INS=<param>];

TYPE=PEN,PEN=<number>, [CONN=<param>];

TYPE=STNO,STNOX=<number>;

The action is used to change the configuration of a voice terminal.

The 3 branches of the parameter tree correspond to the functions:

TYPE=DEV ....	Replace voice terminal
TYPE=PEN ....	Change PEN of voice terminal
TYPE=STNO ...	Interchange station numbers of two voice terminals

Examples

Reconfigure ANATE with STNO 2200 to OPTISET (as main station number).

Input:

CHANGE-SXSU:STNO=2200,TYPE=DEV,OPT=OPTI,DVCFIG=OPTISET,CONN=DIR,PEN=1-5-61-0;

Output:

 H06: VOICE CALL PROTECTION HAS BEEN ACTIVATED FOR THE NEW TERMINAL.
 H02: LOST FEATURES:
 - TIMED REMINDERS
 H01: NOTE !!! 
 THE NEW PEN OF THE STATION IS 1-5-61-0.
 THE MDF STRAPPING MUST BE CHANGED ACCORDINGLY.
 H09: THE STATION WITH THE NUMBER 2200 WAS REFERRED TO
 CALL PROCESSING FOR STARTUP

Change PEN of voice terminal with number 2205.

Input:

CHANGE-SXSU:STNO=2205,TYPE=PEN,PEN=1-1-109-5;

Output:

 H16: MOVING TO PEN 1-1-109-5 INCLUDES THE FOLLOWING STATION NUMBERS:
 2205
 H25: THE STATION(S) AT PEN 1-1-109-5 WERE REFERRED TO
 CALL PROCESSING FOR STARTUP.

Interchange station numbers 2200 and 2300.

Input:

CHANGE-SXSU:STNO=2200,TYPE=STNO,STNOX=2300;

Output:

CHANGE COMPLETED;

Parameter description

BGNAMEN
	Type of Input:	single value, mandatory
	Possible Values:	SLMA		DB_LN_AM_SLMA
		SLMO		DB_LN_AM_SLMO
		SLMQ		DB_LN_AM_SLMQ
		SLMQ3		DB_LN_AM_SLMQ3
		SLMS		DB_LN_AM_SLMS
		STMD		DB_LN_AM_STMD_S0
CONN	device connection type
	Type of Input:	single value, mandatory			(CHANGE,TYPE=DEV-change device,OPT=OPTI-optiset)
	Type of Input:	single value, optional			(CHANGE,TYPE=PEN-change pen)
	Possible Values:	DIR	direct connection
		EXT	off premises/external station connection		(CHANGE,TYPE=PEN-change pen)
		IP	IP connection		(CHANGE,TYPE=PEN-change pen)
		PNT	connection via private network terminator
COS1	class of service 1
	Type of Input:	single value, optional
	Possible Values:	numeric, 1-1000
COS2	class of service 2
	Type of Input:	single value, optional
	Possible Values:	numeric, 1-1000
DIGNODIS	digite with no display
	Type of Input:	single value, optional
	Possible Values:	NO	no
	Possible Values:	YES	yes
DVCFIG	device configuration
	Type of Input:	1 to 2 single values, concatenated with &, mandatory			(CHANGE,TYPE=DEV-change device,OPT=SCSU-scsu-devices)
	Type of Input:	single value, optional			(CHANGE,TYPE=DEV-change device,OPT=OPTI-optiset / CHANGE,TYPE=DEV-change device,OPT=OPTIEXP-optiset expansion)
	Possible Values:	ANATE	analog voice terminal		(CHANGE,TYPE=DEV-change device,OPT=SCSU-scsu-devices)
		DTEA	data terminating equipment (analog)		(CHANGE,TYPE=DEV-change device,OPT=SCSU-scsu-devices)
		FAX	fax device (analog)		(CHANGE,TYPE=DEV-change device,OPT=SCSU-scsu-devices)
		OPTISET	digital voice terminal optiset, upn/cornet-ts		(CHANGE,TYPE=DEV-change device,OPT=OPTI-optiset / CHANGE,TYPE=DEV-change device,OPT=OPTIEXP-optiset expansion)
HFREE	hands free possible
	Type of Input:	single value, optional
	Possible Values:	NO	no
	Possible Values:	YES	yes
INS	station(s) in service
	Type of Input:	single value, optional
	Possible Values:	NO	no
	Possible Values:	YES	yes
LCOSV1	lcr-class-of-service-1 (voice)
	Type of Input:	single value, optional
	Possible Values:	numeric, 1-1000
LCOSV2	lcr-class-of-service-2 (voice)
	Type of Input:	single value, optional
	Possible Values:	numeric, 1-1000
MAINO	primary station number of a bus configuration
	Type of Input:	single value, mandatory
	Possible Values:	numeric, up to 12 characters
OPT	specification of devcie type resp. bus type
	Type of Input:	single value, mandatory
	Possible Values:	OPTI	optiset
		OPTIEXP	optiset expansion
		SCSU	scsu-devices
PEN	port equipment number: ltg-ltu-slot-cct
	Type of Input:	4 single values, concatenated with -, mandatory
	Possible Values:	numeric, 0-242
SECR	station is to become secretary
	Type of Input:	single value, optional
	Possible Values:	NO	no
	Possible Values:	YES	yes
STD	number of key layout/map standard
	Type of Input:	single value, optional
	Possible Values:	numeric, 0-127
STNO	station number
	Type of Input:	single value, mandatory
	Possible Values:	numeric, up to 12 characters
STNOX	station number to be exchanged
	Type of Input:	single value, mandatory
	Possible Values:	numeric, up to 12 characters
TYPE	branch parameter (type of action)
	Type of Input:	single value, mandatory
	Possible Values:	DEV	change device
		PEN	change pen
		STNO	change station number

Error Messages


- NO FREE STATION NUMBER AVAILABLE FOR INTERMEDIATE STORAGE	- NO FREE STATION NUMBER AVAILABLE FOR INTERMEDIATE STORAGE
F01	F01: THE STATION WITH THE NUMBER @@@@@@@@@@@@ HAS NOT YET BEEN ASSIGNED.
F02	F02: THE CIRCUIT COULD NOT BE BLOCKED. PLEASE REPEAT COMMAND LATER!
F02	F02: THE STATION WITH THE NUMBER @@@@@@@@@@@@ COULD NOT BE BLOCKED.
F03	F03: THE SPECIFIED PRIMARY STATION NUMBER @@@@@@@@@@@@ IS NO STATION NUMBER (DPLN).
F03	F03: THE SPECIFIED NUMBER @@@@@@@@@@@@ IS NO STATION NUMBER (DPLN).
F04	F04: NEW DEVICE TYPE IS SAME AS OLD DEVICE TYPE. IT CANNOT BE PROCESSED USING TYPE=DEV.
F05	F05: THE ANATE CANNOT BE REPLACED BY @@@@@@@ BECAUSE IT IS STILL @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
F05	F05: THE ANATE CANNOT BE EXCHANGED BECAUSE IT IS STILL @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@.
F06	F06: THE TERMINAL CANNOT BE PROCESSED BECAUSE IT IS CONFIGURED IN AN EXECUTIVE/SECRETARY SYSTEM AS A REPRESENTATIVE (AMO CHESE).
F06	F06: THE TERMINAL CANNOT BE REPLACED BY @@@@@@@ BECAUSE IT IS CONFIGURED IN AN EXECUTIVE/SECRETARY SYSTEM (AMO CHESE).
F07	F07: THE PRIMARY STATION NUMBER @@@@@@@@@@@@ IS CAMP-ON BLOCKED REPEAT COMMAND LATER OR DEACTIVATE IMMEDIATELY (AMO DSSU)
F08	F08: THE PRIMARY STATION NUMBER @@@@@@@@@@@@ MUST BE DEACTIVATED (AMO DSSU)
F09	F09: DEVICE CONNECTION TYPE NECESSARY
F11	F11: @@@@@@@@ VALUE SPECIFIED IN PARAMETER PEN IS INVALID.
F12	F12: THE SPECIFIED @@@@@@@@ HAS NOT BEEN ASSIGNED YET.
F13	F13: DIU-S2 HAS NOT BEEN ASSIGNED FOR THE SPECIFIED PEN.
F13	F13: DIU-N2 RESP. DIU-N4 HAS NOT BEEN ASSIGNED FOR THE SPECIFIED PEN.
F13	F13: SLMQ+ HAS NOT BEEN ASSIGNED FOR THE SPECIFIED PEN.
F13	F13: THE DEVICE CONFIGURATION CANNOT BE CONFIGURED AT THE ENTERED PEN (WRONG BOARD TYPE RESP. NO BOARD ASSIGNED.)
F13	F13: @@@@@ HAS NOT BEEN ASSIGNED FOR THE SPECIFIED PEN.
F14	F14: THE SPECIFIED PEN IS NOT AVAILABLE.
F16	F16: THE DEVICE COMBINATION SPECIFIED IN PARAMETER DVCFIG IS INVALID.
F17	F17: THE STATION NUMBER(S) CANNOT BE (INTER)CHANGED BECAUSE OF INSUFFICIENT RESOURCES, POSSIBLE REASONS - NO BLK100 MEMORY AVAILABLE (AMO DIMSU) - NO STN MEMORY AVAILABLE (AMO DIMSU)
F18	F18: ANATE&@@@@@@@@ CANNOT BE CHANGED TO @@@@@@@ BECAUSE THE NV DEVICE IS IN A @@@@@@@@ HUNTING GROUP.
F19	F19: @@@@@@@@@@@@ SOURCE DEVICE @@@@@@@@ CANNOT BE PROCESSED BY AMO SXSU
F20	F20: THE COS @@@@@ IS NOT ASSIGNED.
F21	F21: STNO AND STNOX ARE IDENTICAL.
F22	F22: ANATE&@@@@@@@@ CANNOT BE CHANGED TO @@@@@@@ BECAUSE THE NV DEVICE IS ASSIGNED TO OTHER STATIONS (AMO TGER).
F23	F23: @@@@@@@@ CANNOT BE REPLACED BY ANATE&@@@@.
F24	F24: THE STATION IS A VIRTUAL STATION. IT CAN ONLY BE PROCESSED WITH TYPE=STNO.
F25	F25: A CHANGE TO ANATE&DTEA IS NOT POSSIBLE BECAUSE THE ANATE IS AN ASSOCIATED STATION.
F26	F26: THE STATION NUMBER LEADS TO THE PEN THAT IS SPECIFIED IN THE PARAMETER PEN.
F27	F27: INSUFFICIENT MEMORY SPACE ( AMO-DIMSU: PARAMETER @@@@ )
F27	F27: INSUFFICIENT MEMORY SPACE ( AMO-DIMSU: PARAMETER @@@@@@@@ )
F28	F28: @@@@@@@@@@@@ CANNOT BE CHANGED. IT IS STILL REFERENCED BY ACD ROUTING TABLES. DELETE THE STATION FROM ACD ROUTING TABLE @@@@@ WITH AMO ACDRT BEFORE REPEATING THIS COMMAND
F29	F29: THE STATION WITH STATION NUMBER @@@@@@@@@@@@ HAS NOT BEEN ASSIGNED (OR NO ADVANCE PROVISION HAS BEEN MADE FOR THIS) IN ITS OWN NODE.
F30	F30: @@@@@@@@@@@@ STATIONS, WHICH HAVE BEEN ASSIGNED WITH AMO @@@@@@, CANNOT BE PROCESSED.
F31	F31: THE ASSOCIATED DCI WITH THE NUMBER @@@@@@@@@@@@ COULD NOT BE BLOCKED.
F32	F32: STATION NO. @@@@@@@@@@@@ IS MAPPED TO STATION @@@@@@@@@@@@ VIA AMO RUFUM; PLEASE USE THIS AMO FOR FURTHER PROCESSING.
F33	F33: DIGNODIS MAY NOT BE SET SINCE STATION @@@@@@@@@@@@ HAS BEEN RESERVED AS A SECRETARY.
F34	F34: STATION @@@@@@@@@@@@ CANNOT BE PROCESSED WITH SECR=NO SINCE IT IS ALREADY CONFIGURED IN THE EXECUTIVE TELEPHONE SYSTEM @@@@ AS SECR.
F34	F34: STATION @@@@@@@@@@@@ CANNOT BE PROCESSED WITH @@@@@@@@=Y SINCE IT IS ALREADY CONFIGURED IN THE EXECUTIVE TELEPHONE SYSTEM @@@@ AS EXEC@@.
F35	F35: @@@@@@@@@@@@ DIGITE NOT EQUIPPED WITH A DISPLAY MAY NOT BE CONFIGURED AS A SECRETARIAL STATION.
F36	F36: PEN @@-@@-@@@-@@@ IS SIGNED_OFF. RELEASE WITH AMO BCSU OR USE AN OTHER PEN.
F37	F37: THE STATION IS SIGNED OFF. SIGN ON WITH AMO DSSU FIRST.
F38	F38: EXCHANGE OF STNO CANNOT BE PROCESSED. THE SUBSCRIBER @@@@@@@@@@@@ HAS STILL ASSIGNED AT LEAST ONE ACD-ATTRIBUTE. BEFORE REPEATING THIS COMMAND EXECUTE THE FOLLOWING COMMAND CHANGE-SDAT:STNO=@@@@@@@@@@@@,TYPE=ATTRIBUT,DATTR=@@@@@@@@@@@@@@@@@@@@@@@@;
F39	F39: THE RELEASE OF THE CONNECTION IS NOT YET DONE COMPLETELY. PLEASE REPEAT THE COMMAND!
F40	F40: @@@@@@@@@@@@ THE STATION CANNOT BE PROCESSED WHILE STILL AT LEAST ONE NON VOICE DEVICE SVC @@@ IS CONFIGURED WITH THIS EXTENSION NUMBER
F41	F41: @@@@@@@@@@@@ THE PRIMARY STATION NUMBER DOES NOT EXIST
F44	F44: A MAXIMUM NUMBER OF 2 OPTISET DEVICES CAN BE SET UP IN THE OPTISET CONFIGURATION
F45	F45: A MAXIMUM OF @ STATION NUMBERS MAY BE ASSIGNED TO A @@@@@@@@ CONFIGURATION
F46	F46: A MAXIMUM OF @ TERMINALS MAY BE ASSIGNED TO A @@@@@@@ CONFIGURATION
F47	F47: THE STATION CANNOT BE PROCESSED BECAUSE THE NECESSARY TERMINAL ADAPTER OPTISPA FOR CONNECTING OPTISET MUST NOT BE PLUGGED AT PRIMARY STATION NUMBER @@@@@@@@@@@@ TOGETHER WITH THE ALREADY EXISTING TERMINAL ADAPTER OPTIABA.
F48	F48: INSUFFICIENT LINE MEMORY SPACE FOR LINES INCREASE WILL REQUIRE SYSTEM REGENERATION
F49	F49: DVCFIG=OPTISET ONLY AVAILABLE FOR CONNECTION TYPE=DIR RESP. PNT
F50	F50: OPTISET CONFIGURATION CANNOT BE EXTENDED TO INCLUDE AN ADDITIONAL DEVICE BECAUSE THERE IS NO SOCKET LEFT FOR THE TERMINAL ADAPTER @@@@@@@@. FOR DVCFIG=OPTISET ONLY A MAXIMUM OF 2 TERMINAL ADAPTERS CAN BE PLUGGED AT ONE TIME.(SEE PARAMETERS OPTICA,OPTIDA,OPTIS0A,OPTISPA,OPTIABA IN DISP-SBCSU:@@@@@@@@@@@@;)
F51	F51: BUS FOR PRIMARY STATION @@@@@@@@@@@@ CANNOT BE EXPANDED BY AMO SXSU @@@@@@@@@@@@@@@@@@
F52	F52: PRIMARY STATION NUMBER @@@@@@@@@@@@ MAY NOT BE SIGNED OFF
F53	F53: NO BUS CONFIGURED AT PRIMARY STATION NUMBER @@@@@@@@@@@@
F54	F54: @@@@@@@@@@@@ CANNOT BE PROCESSED, BECAUSE AS SECOND TERMINAL AT BUS CONFIGURATION AN ASSOCIATED DCI IS CONFIGURED
F55	F55: @@@@@@@@@@@@ CANNOT BE PROCESSED BECAUSE THE NUMBER OF ORDERED SUBSCRIBERS IS REACHED. USE DISP-CODEW FOR DISPLAY OF THE CONTRACTED FEATURE PACKAGES PLEASE CONTACT YOUR SERVICE CENTER IF YOU WISH TO ADD MORE SUBSCRIBERS.
F56	F56: CHANGE OF PEN NOT POSSIBLE FOR EXISTING DEVICE CONFIGURATION
F57	F57: EXCHANGE OF STNO CANNOT BE PROCESSED. THE SUBSCRIBER @@@@@@@@@@@@ HAS STILL ASSIGNED THE ATTRIBUTE @@@@@@@@ (AMO SDAT).
F58	F58: @@@@@@@@@@@@ THE STATION CANNOT BE PROCESSED BECAUSE THE REQUIRED CONFIRMATION BY CALL PROCESSING HAS NOT BEEN RECEIVED YET - REPEAT COMMAND LATER
F59	F59: THIS OFF PREMISES STATION CAN NOT BE PROCESSED WITH AMO SXSU
F60	F60: AT BOARD SLMQ3 ONLY AN OPTI-CONNECTION WITH MAX. ONE DEVICE CAN BE CONFIGURED
F61	F61: THE SUBSCRIBER IS A MEMBER OF AN ACTIVE NIGHT OPTION TYP=STN AND CANNOT CANNOT BE PROCESSED USING TYPE=DEV.
F62	F62: ONLY PEN CHANGE IS POSSIBLE FOR IP DEVICES. CHANGE OF STNO @@@@@@@@@@@@ CAN BE PERFORMED VIA SBCSU.
F63	F63: THE LCOS @@@@ IS NOT ASSIGNED.
F64	F64: THE CHANGE OF SIP-DEVICES (@@@@@@@@@@@@) IS NOT SUPPORTED BY AMO SXSU.
F65	F65: CHANGE NOT PERFORMED. SUBSCRIBER IS MEMBER OF ONS GROUP @@@@. GROUP HAS TO BE DELETED FIRST.
F66	F66: CHANGE NOT PERFORMED. SUBSCRIBER @@@@@@@@@@@@ IS CONFIGURED AS KEYSET.
F67	F67: THE CHANGE OF UFIP-DEVICES (@@@@@@@@@@@@) IS NOT SUPPORTED BY AMO SXSU.
F68	F68: DVCFIG=OPTIIP RESP. UFIP AVAILABLE ONLY FOR CONN=IP
F69	F69: LICENSE VIOLATION AT SOFTGATE/ENTGW @@-@@. IT IS NOT POSSIBLE TO MOVE THE SUBSCRIBER ON THE SPECIFIED PEN.
F99	F99: THIS FUNCTION IS NOT IMPLEMENTED TEMPORARYLY

Advisory Messages

H01	H01: THE PEN @@-@@-@@@-@@@ OF THE STATION WAS RETAINED.
H01	H01: NOTE !!! THE NEW PEN OF THE STATION IS @@-@@-@@@-@@@. THE MDF STRAPPING MUST BE CHANGED ACCORDINGLY.
H01	H01: THE PEN OF THE STATION IS @@-@@-@@@-@@@.
H02	H02: LOST FEATURES: - @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@
H03	H03: PARAMETER STD IS IRRELEVANT FOR DVCFIG=ANATE AND WILL BE IGNORED.
H04	H04: PARAMETER CONN IS IGNORED FOR EXISTING DEVICE CONFIGURATION.
H05	H05: PARAMETER SECR IS IRRELEVANT FOR DVCFIG=@@@@@@@@ AND WILL BE IGNORED.
H06	H06: VOICE CALL PROTECTION HAS BEEN ACTIVATED FOR THE NEW TERMINAL.
H07	H07: STATION NUMBER WAS CHANGED FROM @@@@@@@@@@@@ TO @@@@@@@@@@@@.
H08	H08: THE STATION WITH THE NUMBER @@@@@@@@@@@@ IS NOT ACTIVE.
H09	H09: THE STATION WITH THE NUMBER @@@@@@@@@@@@ WAS REFERRED TO CALL PROCESSING FOR STARTUP.
H10	H10: THE PARAMETER PEN IS IGNORED BECAUSE NO OTHER PEN (MODULE) IS REQUIRED.
H11	H11: THE ASSOCIATED DCI WITH THE NUMBER @@@@@@@@@@@@ IS NOT ACTIVE.
H12	H12: THE ASSOCIATED DCI WITH THE NUMBER @@@@@@@@@@@@ WAS REFERRED TO CALL PROCESSING FOR STARTUP.
H13	H13: FOR ALL STATIONS, WHOSE DSS DESTINATION WAS STATION @@@@@@@@@@@@, THE DESTINATION WAS DELETED.
H14	H14: PARAMETER HFREE IS IRRELEVANT FOR DVCFIG=@@@@@@@@ AND WILL BE IGNORED
H15	H15: PARAMETER DIGNODIS IS IRRELEVANT FOR DVCFIG=@@@@@@@@ AND WILL BE IGNORED
H16	H16: MOVING TO PEN @@-@@-@@@-@@@ INCLUDES THE FOLLOWING STATION NUMBERS @@@@@@@@@@@@ @@@@@@@@@@@@ @@@@@@@@@@@@ @@@@@@@@@@@@
H17	H17: THE TERMINAL ADAPTER OPTIS0A PLUGGED AT PRIMARY STATION NUMBER @@@@@@@@@@@@ IS NO LONGER NEEDED
H18	H18: SLMAR-PEN'S ARE SKIPPED FOR AUTOMATIC PEN SEARCH (NO PEN IN COMMAND).
H19	H19: WHEN CHANGING A TERMINAL WHICH IS PERPARED TO BE A SECRETARY FOR AN EXECUTIVE/SECRETARY SYSTEM (SECR=YES BUT NOT YET ASSIGEND TO AN EXECUTIVE/SECRETARY SYSTEM) TO @@@@@@@, THE SECRETARY PREPARATION WILL BE REMOVED.
H20	H20: @@@@: RNGXFER KEY(S) WITH NO FUNCTION, PLEASE CHECK ASSIGNED KEYLAYOUT
H21	H21: SECR: PUS KEY(S) WITH NO FUNCTION, PLEASE CHECK ASSIGNED KEYLAYOUT
H22	H22: SUBSCRIBER @@@@@@@@@@@@ WAS DEACTIVATED IMMEDIATLY FOR LONG PERIOD. (NEQ STATE)
H23	H23: PLEASE CHECK SIGNALING MODE OF CALL PICKUP-GROUP @@@@ (AMO-AUN)
H24	H24: THE TERMINAL-ADAPTER @@@@@@@@ MUST BE PLUGGED AT MAIN STATION NUMBER @@@@@@@@@@@@
H25	H25: THE STATION(S) AT PEN @@-@@-@@@-@@@ WERE REFERRED TO CALL PROCESSING FOR STARTUP.
H26	H26: @@@@@@@@@@@@ ... STILL WAITING FOR A CONFIRMATION BY CALL PROCESSING (MAXIMUM @@@ SEC)
H27	H27: FOR SET600 AT SLMQ3 ONLY CONN=PNT IS VALID, PARAMETER CONN WILL BE IGNORED.
H28	H28: **** PLEASE NOTE : ******************************* THE CONTRACTED NUMBER OF FLEX LICENSES IS EXCEEDED. FLEX LICENSE IS MARKED AS TRIAL ENTITY. THE FEATURE FLEX LICENSE WILL BE DEACTIVATED, IF TRIAL MODE EXPIRES WITHOUT SUFFICIENT LICENSES. ***********************************************************
H29	H29: FOR INTERMEDIATE STORAGE STNO @@@@@@@@@@@@ WAS USED TEMPORARILY
H30	H30: THE EXISTING DPLN OF THE STATION IS NOT IN ADPLN OF THE NEW NODE, SO IT IS INTERNALLY SET TO THE DPLN OF THE NEW NODE.
H31	H31: DEVICE @@@@@@@@@@@@ WAS A CIRCUIT DESK. @@@@@@@@@@@@ IS NEW CIRCUIT DESK. PLEASE UPDATE CIRCUIT SETTINGS ACCORDINGLY. PLEASE INITIATE DATA CHANGE WITH RESTART OF THE CIRCUIT CLIENT. ( RESTART-DSSU:TYPE=STNO,STNO=@@@@@@@@@@@@ ; )
H32	H32: DEVICES @@@@@@@@@@@@ AND @@@@@@@@@@@@ ARE CIRCUIT DESKS. PLEASE INITIATE DATA CHANGE WITH RESTART OF THE CIRCUIT CLIENTS. ( RESTART-DSSU:TYPE=STNO,STNO=@@@@@@@@@@@@ ; ) ( RESTART-DSSU:TYPE=STNO,STNO=@@@@@@@@@@@@ ; )
H33	H33: NEW E164 NUMBERING FOR CIRCUIT DESKS DUE TO NODE CHANGE. PLEASE UPDATE CIRCUIT SETTINGS ACCORDINGLY.
H34	H34: @@@@@@@@@@@@ STATION HAS BEEN MOVED TO IP BOARD @@@.@@@.@@@.@@@. PHONE GATEWAY IP OR CGWB IPADR MAY NEED UPDATE.
H99	H99: THIS FUNCTION IS NOT YET IMPLEMENTED.