AACD

PNSF Call Wait at ACD unknown for orig. node of CAS

x

x

ACDG

ABNA

Synchronized announcement with attendant intercept on busy or no answer.

x

x

ABPD

Answer before postdial or announcement.

If set, an "answer" to the A station is sent before an announcement is started. This enables the A station to hear the announcement.

x

x

ACH3

Special classmark assignment for an outgoing consultation call by the attendent with a CO party on hold - required trunks to OpenScape Business/HiPath 3000

x

x

ACRC

AC with reverse charging.

x

x

AC

ACTR

AC with call tracing.

x

x

AC

ADIU

Attenuation of DIUC trunk circuits, CIS.

x

x

CIS

AEOD

Line with advanced end-of-dial transmission (e.g. for DP and MOSIG signalling).

For transit connections, when this parameter is set, an advanced end-of-dial is sent to the incoming circuit.

This parameter is set for critical time conditions!

x

x

AI1

Announcement of incoming seizure type 1, TSC (Italian Railway)

x

x

Italy

AI1N

Announcement of incoming seizure type 1 and own node no., TSC (Italian Railway)

x

x

Italy

AI2

Announcement of incoming seizure type 2, TSC (Italian Railway)

x

x

Italy

AI2N

Announcement of incoming seizure type 2 and own node no., TSC (Italian Railway)

x

x

Italy

AI3

Announcement of incoming seizure type 3, TSC (Italian Railway)

x

x

Italy

AI3N

Announcement of incoming seizure type 3 and own node no., TSC (Italian Railway)

x

x

Italy

Attendant intercept, if an already forwarded connection is to be re-routed to a trunk.

If this parameter is set, then already forwarded incoming connections which are to be re-routed to a trunk are intercepted by the AC. If the parameter is not set the connections are released.

This parameter is only valid for incoming circuits with MFC signalling.

x

x

CFW

AMFC

Automatically DTMF conversion on incoming calls while in talk (AMFC will be ignored when AMO SBSCU parameter TRACE is set).

x

x

ANDY

ANI delivery in mixed networks.

x

x

ANHT

When entering a call in the hunting group call queue an announcement is activated.

For use in countries where instead of a free tone, a waiting tone is sent when calls are waiting in the hunting group call queue (i.e. Finland)

x

x

ANIC

Line with ANI Codogramm transmission (see COP value ANIC), CIS

x

x

CIS

ANNA

On attendant intercept, a text announcement is started.

The announcement connection is configured using AMO SSC, TYPE=EXTANN, CPCALL=ANNICPT

x

x

ANNC

Local announcement. For incoming analog connections a local announcement is activated. An alternative is to enter one of the following parameters: NTON, VM, DTNI, DTNE or ANNC. Then the relevant SIU tone will be activated.

x

x

ANOD

Activate the synchronized announcement immediately,see also AMO COP, value AANT

x

x

Answer from the line

This parameter marks lines which have a signalling procedure with answer criteria.

x

x

AOCC

Call charge transmission per connection. Must always be set for CORNET-NQ and QSIG

x

x

CDRE

APPR

Settings are relevant for test purposes and approvals.

x

x

APSM

Synchronized announcement if PSM

x

x

ARCF

Convert alternate routing on error to CFU

x

x

ASTN

A-stationnumber will be checked if allowed for outgoing CO use. Allowed A-numbers have to be entered in dial plan DAR ASTN by means of AMO WABE (ANI CIS)

x

x

CIS

ATDI

Identification of AC (MFC)

The CO requests the subscriber number for incoming calls to AC.

x

x

MFC (ITU Q.320-490)

Transit counter administration for S0/S2 lines. Configuration of the threshold value in the network using AMO TDCSU, parameter TRACOUNT.

x

x

BCCC

B channel through-connection when the B side answers.

This parameter is only set when the OpenScape 4000 functions as a DSS1 trunk, and if the network provider requests that the B channel is only through-connected when the called party answers. Otherwise the B channel is through-connected when the connection has been established.

x

x

B channel negotiation in order to prevent a "preferred-preferred collision". Only necessary for connection to an external system. In this case in AMO TDCSU the parameter BCNEG=Y must be set.

x

x

EDSS1

BFSR

Block forwarding switching after reject

x

x

CFW

BKNA

Activation disables feature Calling Name Delivery

x

x

USA

BLOC

If this parameter is set, the field SENDING_COMPLETE is set to TRUE as soon as the pulse series counter limit is reached (provided by external toll restriction, depends on dialled digits). With QSIG this parameter is always set !!

x

x

This parameter releases the trunk connection on no answer after recall to the originator (AC or night station). The release time after a recall is set with the RELREC parameter of AMO CTIME.

x

x

BRLA

Branch line, Austria

This parameter marks a line as a branch line (11-wire analog tie line with a critierion plan especially for Austria). It may not be set for any other line type.

x

x

Austria

BSHT

Calls to a busy hunting group are not released but linked into the hunting group's call queue. ICPTDID must be set in AMO FEASU.

x

x

CACO

All incoming ISDN Calling Numbers must be extended with the Alternative Country Code Number (from central switch data, ZANDE), if not already done.

x

x

CATR

If set, charges are transmitted for analog lines (condition: lines are configured for call charge transmission).

x

x

CDR

CBBN

Network-wide callback on busy (only with VFSS and S0/S2)

x

x

CBFN

Network-wide callback on free (only with S0/S2)

x

x

CCRO

Completion of Call Retention Option

details see Chapter 32, "EDSS1 System Interface / Trunk Interface"

x

x

DSS1

Circuit number, CCT-NO in AMO TACSU is used as A number for incoming seizure (CIS).

x

x

CIS

The CDR component Record Point via this line is marked as Breakout.

x

x

CDR

Call Deflection Network-wide

x

x

CFW

CDRD

If set, the authorization of the circuit's COS and not the transmitted authorization of the line is used for CDR. This controls at the carrier whether or not the service AOC (Advice of Charge) has been activated for customers.

This parameter has nothing to do with billing on the terminal.

x

x

CDR

CDURSUPR

Activation of Supervision of Transit Connection for incoming transit connections.

For more information please refer to Chapter 47, "Restricted Call Duration for Transit Calls".

---

x

CEBC

Call extension for busy or call state. This applies for analog and digital trunks.

See also parameters CEOC, CEBX and CEOC are mutually exclusive.

x

x

CECO

Call extension by AC to busy station with camp-on.

x

x

CEOC

Extension via line is only possible in talk state. This applies fir analog and digital trunks.

This parameter is a subset of CEBC. CEBC and CEOC are mutually exclusive!

x

x

Call Forward Busy Network-wide

x

x

CFW

Network wide call forwarding possible. (valid for all outgoing/incoming circuits with S0/S2 interfaces for trunk/tie traffic Cornet-N or ECMA-Qsig protocols)

x

x

CFW

Setting FWD for the main station possible. The FWD is activated at the provider.

x

x

CFW

Accessiblilty check of the forwarding destination is possible over the line. Valid only for tie connections: an accessiblilty and name is checked.

x

x

CHRT

Changeover from hold to ringtone. With transfer before answer ringtone is to be injected instead of hold tone.

x

x

CLAC

Action based on CLI (used for trunk) (see Chapter 100, "Calling Line Identification (CLI) Enhancements")

x

x

replaces R279

CLNA

CLI name translation (used for trunk) (see Chapter 100, "Calling Line Identification (CLI) Enhancements")

x

x

replaces R277

CLNI

CLI number unknown - no intercept to AC (see Chapter 100, "Calling Line Identification (CLI) Enhancements")

x

x

replaces R284

CLN0

CLI number modification (used for trunk) (see Chapter 100, "Calling Line Identification (CLI) Enhancements")

x

x

replaces R278

COEX

Class of externals (Application for China, protocol CSN1)

Those circuits are marked which are used for the exchange of these COEXs (COSs, see AMO COSSU).

x

x

Also CIS, France

COTN

An internal (simulated) exchange tone is transmitted down the line for outgoing exchange connections.

This is not required for LCR. It only set for all digital tie circuits. The parameter also prevents the early deactivation of the trunk dialling tone in tie traffic.

x

x

COVN

CO connection through CORNET VN protocol

x

x

CPS6

If this parameter is set, CPS6 is used for digit analysis for incoming trunk connections.

Example:

Trunk in PBX A.

AC is located in PBX B.

The "0" has two meanings in PBX B:

For incoming trunk calls the "0" reaches the AC. For all other connections the "0" seizes a trunk. By setting CPS6 this is exactly achieved.

x

x

CSN7

Identification for DIUS2 circuits to CSN7 networks, China

x

x

China

CTAL

Extension only in call or talk state allowed. Applies for analog and digital trunks.

x

x

Controlled trunk and line selection not allowedl, has to be set to forgein nodes

x

x

Controlled trunk and line selection

x

x

Closed User Group

x

x

CWBS

Call waits when station is busy, (CWBS and IBSY cancel each other out!)

Set in AMO FEASU, ICPTDID

x

x

DATA

Trunk for data

x

x

DCCO

Derive the node number from the CALLING NUMBER, for incoming CO calls.

x

x

DCPA

Trunk is not able to signalize Directed Call Park

x

x

DDIC

DDI Control

x

x

replaces R282

Use default node number of trunk.

x

x

DI1

Dialtone on incoming seizure type 1, TSC

(Italian Railway)

x

x

Italian Railway

DI1N

Dialtone on incoming seizure type 1 and own node no., TSC (Italian Railway)

x

x

Italian Railway

DI2

Dialtone on incoming seizure type 2, TSC

(Italian Railway)

x

x

Italian Railway

DI2N

Dialtone on incoming seizure type 2 and own node no., TSC (Italian Railway)

x

x

Italian Railway

DI3

Dialtone on incoming seizure type 3, TSC

(Italian Railway)

x

x

Italian Railway

DI3N

Dialtone on incoming seizure type 3 and own node no., TSC (Italian Railway)

x

x

Italian Railway

Display dailed number of subscriber B at subscr. A

x

x

DIT

dedicated incoming trunk

x

x

USA

DIUD

DIUC with digital data transfer (i.e. China)

This parameter is only set for trunk circuits.

(In WABE set the DARs DTED, DTE and/or combi-code DTEDNO, DTENO and with AMO RUFUM set the conversion to the relevant DTE devices).

x

x

DPRE

If this parameter is set, the actually transmitted dialed digits (e.g. prefix digits, AMO LODR, OUTPULSE) are sent to CDR.

x

x

DSDL

If set, no call forwarding information (Diversion Legs) is sent.

Valid for DSS1 and QSIG (Cornet-NQ) lines.

x

x

CFW

disconnect supervision for incoming trunk

x

x

DTMF

Inband DTMF when SETUP contains no classmarks

x

x

DTMP

Line with multi-frequency signalling PAKKED (CIS)

x

x

CIS

DTMS

Line with multi-frequency signalling procedure SHUTTLE (CIS)

x

x

CIS

DTNE

With incoming analaog connections external dialtone is injected, alternatively, one of the following parameters can be specified: NTON, VM, DTNI, DTNE or ANNC.

The corresponding SIU tone is injected. For outgoing seizure the connection is marked as CO call (only with digital trunks)

x

x

DTNI

With incoming analog connections internal dialtone is injected. Alternatively, one of the following parameters can be specified:

NTON, VM, DTNI, DTNE or ANNC. The corresponding SIU tone is injected.

x

x

EDBA

Line with emergency disconnect before answer.

x

x

EODL

Emergency override/disconnect only local. Disconnect possible for all analog and digital circuits with the exception of APSE and PSM/CC.

x

x

ETE

MFC-R2 End-to-End

details see Chapter 38, "MFC-R2 Signaling"

x

x

MFC-R2

ETE1

MFC-R2 End-to-End 1 details see Chapter 38, "MFC-R2 Signaling"

x

x

MFC-R2

ETE2

MFC-R2 End-to-End 2 details see Chapter 38, "MFC-R2 Signaling"

x

x

MFC-R2

ETE3

MFC-R2 End-to-End 3 details see Chapter 38, "MFC-R2 Signaling"

x

x

MFC-R2

ETE4

MFC-R2 End-to-End 4 details see Chapter 38, "MFC-R2 Signaling"

x

x

MFC-R2

ETE5

MFC-R2 End-to-End 5 details see Chapter 38, "MFC-R2 Signaling"

x

x

MFC-R2

UUS ETSI conform details see Chapter 32, "EDSS1 System Interface / Trunk Interface"

x

x

DSS1

FAX intercept when free to phone mail for incoming faxes via trunk.

x

x

FAX intercept when busy to phone mail

x

x

FLOV

MLPP flash override call - high level

x

x

MLPP

FLSH

MLPP flash call

x

x

MLPP

Activation of rerouting with network-wide ring no answer.

x

x

Unconditional all forwarding with re-establishment of the connection to the forwarding destination network wide.

If this parameter is set, in the case of call forwarding, the forwarding number is returned to the originating node which then establishes a connection to this number. The first connection is released. Valid for all digital interface circuits and must be set in the entire network.

From EV1.0, FWDN is supplemented by the COT parameter CFVA which, which instigates a destination check for a network-wide FWD.

CFBU and FWDN are mutually exclusive!

x

x

CFW

FWDR

Call forwarding is carried out via re-routing into the public network (Application for France).

Call forwarding into the public network with a transit connection in the OpenScape 4000 will not be realized.

x

x

France

HGTR

Hunt group service transportable to partner node

x

x

IBBA

Send digits via in-band DTMF before answer

x

x

IBSY

Attendant intercept when busy (IBSY and CWBS cancel each other out!).

Set in AMO FEASU, ICPTDID

x

x

ICZL

Incoming CDR via zone or from line.

CDR for incoming traffic is calulated using zone tables (tariff tables) or line billing information (messages). ICZL and ICZO cancel each other out!!

x

x

CDRE

ICZO

Incoming CDR only via zone.

Billing for incoming traffic is calulated using zone tables (tariff tables). Billing information from the line is not possible. ICZO and ICZL cancel each other out!!

x

x

CDRE

IDIS

If this parameter is set, all calls with unauthorized dialling codes are switched to the attendant, example: WABE DAR are not permitted for MFC Lines).

Only valid for MFC circuits.

x

x

IDND

Attendant intercept for do-not-disturb. Set in AMO FEASU, ICPTDID.

x

x

IEVT

Diagnostic parameter for registration of implausible events.

x

x

IFR

Attendant intercept when free after timeout. Set in AMO FEASU, ICPTDID.

x

x

IGID

Ignore the call ID (i.e. for billing) for incoming connections. The received call ID is ignored and a new one issued (i.e. on the carrier's network borders).

x

x

Ignore incoming billing elements.

The received paying party and NOTRANS bit (AMO LDAT) from the billing element are ignored.

x

x

CDRE

IIDL

Attendant intercept when dialling is incomplete. Set in AMO FEASU, ICPTDID.

x

x

IMDI

MLPP immediate call

x

x

MLPP

INAU

Attendant intercept when the dialed station is not authorized.

x

x

INDG

Attendant intercept when no dialling occurs (do not set with DP!!)

Set in AMO FEASU, ICPTDID.

x

x

IONS

Attendant intercept if a remote override has failed. Set in AMO FEASU, ICPTDID.

x

x

IRTO

Italian Railway tone.

This parameter is to be set for mixed networks (analog/digital) when an interdigit tone is to be recognized. If not set recognition of an interdigit tone is only possible with analog circuits.

x

x

Italy

ITB

Attendant intercept when all trunks busy (i.e. also call queue full). Set in AMO FEASU, ICPTDID.

x

x

ITRC

If this parameter is set and call transfer is carried out, the recall timer is started in the PBX of the transferring party.

This parameter is only relevant for PBXXX

( Cornet DPNSS1 Gateway ).

x

x

If this parameter is set, the number of the trunk circuit is used instead of the transmitted ITR group.

x

x

ITT

For incoming seizure the CPS 12 (incoming inter-exchange traffic) is set. This parameter applies for analog and digital trunks.

Depending on CPS12, exact results can be achieved by digit analysis. If parameter ITT is not set, the digit analysis evaluates incoming digits using CPS10 (incoming extension line).

ITT and TIE are mutually exclusive!!

x

x

IVAC

Attendant intercept when the call number is not available (WABE). Set in AMO FEASU, ICPTDID .

x

x

Camp-on on DID calls (AS and QS)

x

x

KNEX

Camp-on after extension of incoming trunk calls (AS and QS)

x

x

For a busy station an override or camp-on over the line is possible (valid for analog and digital circuits)

x

x

KNTE

Knock override to anate using tie-lines allowed

Automatically override to extension using TIE-Lines This parameter has the same functionality as KNDI for CO calls (but for TIE lines!)

x

x

LBPR

LB Line partner for release control

x

x

Pakistan/Air Force

Lines with implicit station numbers for carrier.

This parameter marks lines from carrier systems to customer systems. These lines are used to send the implicit station numbers (without exit ID i.e. 098 722 4711 or only 4711) as Calling Number. It should always be set on the carrier system.

LINC and LINO may not be used together!!

x

x

LINO

Lines with implicit station numbers.

This parameter must always be set if old (< Hicom 300 V3.5) or external systems connected to this line can only accept implicit station numbers and transmit an undefined or incorrect NPI/TON combination to a destination number. To determine this generally takes a great deal of effort. It is therefore recommended that the COT parameter for lines to old or external systems be set.

LINO and LINC may not be used together!!

x

x

LPRN

Line with permanent restricted numbers to EDSS1 CO

x

x

EDSS1

With multiple FWD the phone mail of the last forwarding destination is activated.

x

x

If set, no node number is sent.

This parameter is set for the features "Station number signaling with open numbering" and "Prevention of network loops and unalloed connections".

x

x

MAOV

Manual override (China)

x

x

China

MCIW

Mailbox call-back interworking with OpenScape Business/HiPath 3000.

This parameter is set in order to achieve error free signalling when a station of a partner node OpenScape Business/HiPath 3000 has placed a call-back request in the mailbox. This applies for QSIG and call-back from the OpenScape Business/HiPath 3000.

x

x

Line with MFC signalling. In AMO MFCTA, MFCVAR> 0 must be set!

x

x

MFOB

This parameter must be set so that an incoming DID call via a main PBX to a satellite PBX can be established, regardless of whether the CORNETN or MFC-R2 protocol for CIS is used. This is the case when a CIS MFR-R2 protocol is used, this means without busy signal and at the same time release control. (see AMO COT, COEX).

x

x

CIS

MCID call clearing control required details see Chapter 115, "DSS 1 Terminals"

x

x

DSS1

MCID identify here details see Chapter 115, "DSS 1 Terminals"

x

x

DSS1

Trunk can be used for mlpp-preemption

x

x

Belgien, USA

MLPP

MRCA

Manual call connection after conference override.

x

x

CIS

MSIR

MSI Line with release control

x

x

Pakistan/Air Force

North America Analog Trunks

x

x

USA

NCDR

Suppress signaling of CDR-E specific messages

x

x

CDRE

NCHD

No charge data during call

If set, no advice of charge information (AOCD) is sent to the partner PBX during the connection.

x

x

CDRE

NCHG

This parameter is obsolete but still exists in the code.

x

x

network call transfer, explicit call transfer

x

x

USA

No CFNR after transfer possible to nodes behind

x

x

No multi-level precedence and preemption on trunk

x

x

MLPP

No intercept with transit.

If set, there is no attendant intercept for transit and outgoing connections.

x

x

This parameter should be set when LCR authorizations (least Cost Routing) cannot be sent over the line (i.e. different protocols), or when the transmitted LCR authorizations are to be ignored. The LCR authorozations for the circuit are used for "voice" (parameter LCOSV).

x

x

LCR

No local hold tone. This parameter allows an external hold tone (i.e. music) from a central place.

x

x

This parameter should be set when LCR authorizations (least Cost Routing) cannot be sent over the line (i.e. different protocols), or when the transmitted LCR authorizations are to be ignored. The LCR authorizations for the circuit are used for "Data" (parameter LCOSD).

x

x

No multi-level precedence and preemption on trunk

x

x

Belgium, USA

MLPP

NMRN

The format of REDIRECTING_NUM doesn't need to be same as REDIRECTION_NUM

x

x

NOCI

No notification for conference supplementary service

x

x

NOCT

No notification for call transfer and call hold supplementary services

x

x

No Flag Trace

x

x

can not be put on hold for network-wide conference

x

x

No re-routing.

This parameter is set for lines without an evaluated end-of-dial or for lines for which after seizure no further re-routing is required.

x

x

LCR

no simple dialog available

x

x

near ton generation

x

x

No override on CO connections.

x

x

NPI ISDN, abgehender Verkehr

x

x

CFW

NPI PRIVATE, abgehender Verkehr

x

x

CFW

NPI UNKNOWN, abgehender Verkehr

x

x

CFW

CorNet-NQ Network-wide Pick-up not supported details see Chapter 76, "Call Pickup"

x

x

CorNet-NQ Pickup-Info not supported details see Chapter 76, "Call Pickup"

x

x

NRAA

Signalling without backwards release after answer (only analog, valid i.e. for transfer).

x

x

NRBA

Signalling without backwards release before answer (only analog, valid i.e. for transfer).

x

x

NTBO

Netborder to private or public net, no rerouting

x

x

No tone. No tone for incoming analog connections. An alternative is to enter one of the following parameters: NTON, VM, DTNI, DTNE or ANNC. Then the relevant SIU tone will be activated.

x

x

off hook queuing für Transiverbindungen

x

x

USA

ORRN

Originally called party number send via redirected number

x

x

CFW

OSCV

OpenScape 4000 - OpenScape Voice interworking

x

x

replaces R283

OVRA

Override for operators (Flash to CO)

x

x

PDOB

Postdial when the dialled station is busy.

x

x

PDOT

Postdial when the dialled station does not answer.

x

x

PGEP

Partner node does not know OpenScape 4000 GEP signalling

x

x

CDRE

PIN remote possible (incoming and outgoing)

This parameter must be set on both sides of the connection.

x

x

PM8D

Phonemail can not handle numbers longer than 8 digits that are marked as internal

x

x

PNEV

Suppression user guidance VMS EG-Display.

With inband signalling, this parameter prevents interference of the voice channel during the transfer of display information from VMS via PNE to the station. This means that spoken user guidance is no longer interrupted. The user guidance on the terminal display is suppressed.

x

x

Priority line.

Up to V2.0: Calls over lines with this parameter set are given priority in the AC call queue.

From V3.0: This parameter marks lines with signalling protocols which can signal line priorities of incoming trunk groups at the network borders.

x

x

PRIC

MLPP priority call

x

x

MLPP

PRNI

Prevent node information

Is this paramter set, no NODE Information (NI) will been sent in the SETUP (BC)

x

x

PROV

Network-wide emergency override/release possible (S0/S2 trunk circuits or E & M and CF signalling).

Condition: in AMO FEASU the feature NAUFTR must be available.

x

x

R277

CLI name translation (used for trunk)

-

-

as of V6 see CLNA

R278

CLI number modification (used for trunk)

-

-

as of V6 see CLN0

R279

Action based on CLI (used for trunk)

-

-

as of V6 see CLAC

R282

DDI Control

-

-

as of V6 see DDIC

R283

OpenScape 4000 - OpenScape Voice interworking

-

-

as of V6 see OSCV

R284

CLI number unknown - no intercept to AC

-

-

as of V6 see CLNI

RCBS

This parameter is set for incoming seizure of a station with "release control" which when the other party goes on hook activates busy tone or displays a fixed text. If the other party picks up the handset again, the busy tone is to be deactivated or the fixed text is deleted. CIS application with ISKRATEL prefix.

x

x

CIS

RCL

Recall to AC if user hangs up after consultation call (applies for all circuits)

x

x

Automatic recalls to the AC are suppressed in nodes without AC. Valid for all circuits.

x

x

RDDI

Line with synchronized announcement as proceed-to-select signal with DDI

x

x

synchr. announcement

receive trailing lin digits

RLIN and SECO may not be used together!!

x

x

ROPT

This parameter is set for lines supporting route optimization

x

x

ROUT

MLPP dsn-routine

x

x

MLPP

Synchronized announcement of non OpenScape 4000 incoming call

x

x

SATC

Satellite connection via S0/S2 lines. Configuration of threshold value for the maximum number of satellite connections in the network with AMO TDCSU, parameter SATCOUNT.

x

x

SATR

Synchronized announcement type transport

x

x

Line with single-digit DID

If set, a partial digital analysis (if activated) for analog and digital circuits will be deactivated.

x

x

Send emergency call outgoing d-channel info

RLIN and SECO may not be used together!!

x

x

Calls incoming over digital central office trunks from other branches via VPN ring as an internal call & calls incoming from other sources ring as an external call.

x

x

Send no billing element (paying party =call number plus node number).

x

x

CDRE

Park system and hold analog connection

x

x

USA

This parameter is set to compress the B channel for voice signaling details see Chapter 57, "Voice Compression"

x

x

VC

SPCP

Voice compression preferred

x

x

VC

Trunk to voice server in foreign node

x

x

STH3

Special classmark assignment for outgoing call by station with CO party on hold - necessary for interworking with OpenScape Business/HiPath 3000

x

x

Suppress name network-wide

x

x

COT in connection with the T-Reference (digital attenuation).

If the 4-wire-connection is to be recognized during device definition in association with an analog connection (tie), then this parameter must be set.

x

x

Incoming tie traffic CO call signaling

x

x

Pakistan/Air Force

Through connection with call tranfser in call state for ISDN transit.

If the parameter is set, the connection is switched through in "Transfer ringing" state and no hold tone is injected.

x

x

Trunk group for re-routing. Only for C-Tel company.

x

x

LCR

TIE

For incoming seizures, the CPS 11 (tie incoming) is always set. This parameter is only valid for analog and digital tie circuits.

This allows, dependant on CPS11, exact results in the digit analysis. If TIE is not set digit analysis of the incoming numbers is nade with CPS 10 (incoming station line).

TIE and ITT cancel each other out!!

x

x

TIEI

Identification of tie lines (MFC)

The CO requests the subscriber number for incoming trunk calls to tie lines.

x

x

MFC (ITU Q.320-490)

TMFC

Seize transit circuit upon completion of MFC signaling (FREE is signaled towards CO), application: France

x

x

France

TMUSIC

Number of music on hold recording

x

x

Tone is injected from the station (for analog and digital S0/S2 trunks).

x

x

Line with 1TR6 link, if OpenScape 4000 emulates the "network side".

This emulates tone injection as if it came from the 1TR6 CO (OpenScape 4000 acts as 1TR6 CO). The protocol variant 1TR6N must be set for the circuit.

x

x

TRAI

If set, tracing of trunk calls is possible. This means a trace can be signalled over this line towards the CO.

x

x

Transfer before answer on DSS1

x

x

TRID

Provide Trunk Data (PEN) for identification by AC

x

x

TRSC

Trunk sends call charges (currency amounts) to originating node.

If TRSC is not set, units are reported to the originating node. where the value Unit is set using AMO ZAND , TYPE=CCD, parameter CDDISPEX

x

x

CDR

TSCS

TSC signaling of the external mailbox messages.

x

x

This attribute set means that this trunk can be connected to another trunk when none of them has Disconnect Supervision.

x

x

US1E

UUS1-explizit Service is allowed

x

x

DSS1

USBT

UUS3 service may be requested by called Party details see Chapter 32, "EDSS1 System Interface / Trunk Interface"

x

x

DSS1

USCC

Congestion Control for User-User Service details see Chapter 32, "EDSS1 System Interface / Trunk Interface"

x

x

DSS1

USCD

Restriced UUS-Services for interaction with Call Diversion details see Chapter 32, "EDSS1 System Interface / Trunk Interface"

x

x

DSS1

USD

Postdial (unrestricted) possible (France).

This parameter is set to allow DIGITEs in call state unrestricted postdialling for established incoming and outgoing connections (analog/CAS_) over the line with the configured dial type.

x

x

France

UUS1

User-User-Service ISDN Class1 (Connection setup request, SET UP Basic Call)

details see Chapter 150, "User-to-User Service"

x

x

DSS1

UUS2

User-User-Service ISDN Class2 (Connection setup Basic Call)

details see Chapter 150, "User-to-User Service"

x

x

DSS1

UUS3

User-User-Service ISDN Class3 (Connection Basic Call)

details see Chapter 150, "User-to-User Service"

x

x

DSS1

Voice compression not allowed details see Chapter 57, "Voice Compression"

x

x

VC

VM

VM tone. For incoming analog connections the VM tone is injected. Alternatively, one of the following parameters may be specified: NTON, VM, DTNI, DTNE or ANNC. The corresponding SIU tone is injected.

x

x

VNCO

Send virtual subscriber number to CO

x

x

VOCE

Trunk for voice

x

x

WAAN

Synchronized wait announcement with call to AC

x

x

synchr. announcement

XFER

Trunk call transfer

x

x

XTRC

If this parameter is set and call transfer is carried out, the recall timer is not started in the PBX of the transferring party but in the PBX of the held party.

This parameter is only relevant for PBXXX

( Cornet DPNSS1 Gateway ).

x

x